TRIBU NODI SOFA User manual

NODI SOFA
ASSEMBLY INSTRUCTIONS
NOSO01 - 20-01-2021

COMPONENTS
Regular
BASE
Regular
PLATE
Extension
BACKREST
Corner
BACKREST
rear
CONNECTOR
inner corner
CONNECTOR
front
CONNECTOR
Deep
BASE
Deep
PLATE
Lounge
BASE
Lounge
PLATE

HARDWARE
RIGHT INSERT LEFT INSERTCORNER INSERT
COUNTERSUNK SCREW
PLASTIC WASHER
FLAT HEAD SCREW
PLASTIC BUSHING

ASSEMBLY INSTRUCTIONS
Determine if you have freestanding Nodi sofa modules or a Nodi sofa set.
FREESTANDING
continue with step
SET
continue with step
1
2
10

ASSEMBLY INSTRUCTIONS
Layout the BASE at it’s final location. The logo marks the back of the BASE.
2
Logo
Every Nodi sofa BASE has adjustable gliders to adapt to uneven floors.
Use a level to make sure the BASE is level. The gliders can accommodate
up to 20 mm height dierence.
3

Lay out the backrest to match your frame.
4
Extension
BACKREST
Corner
BACKREST
Use FLAT HEAD SCREW, PLASTIC WASHER and PLASTIC BUSHING to attach the
BACKREST to the BASE. 4 x for Extension BACKREST, 6 x for corner BACKREST.
5
Plastic washer
Flat head screw
Plastic bushing

When the backrest is assembled it is time to install the INSERTS. It
depends on your module (regular, deep, lounger) which INSERTS you
need.
7
Corner Insert
Corner Insert
Right Insert
Left Insert
Add the plate, make sure the PLATE matches with the BASE.
Each PLATE has a logo, match it with the logo on the BASE.
Use COUNTERSUNK SCREWS to attach the plate to the BASE.
8

Every seat cushion has a Tribù logo, make sure the logo is in the rear, on
the right. Make sure the triangular fabric gather is pointing towards the
backrest.
9
Fabric gather
Logo

Layout the BASES at their final location. The logo marks the back of the
BASE, make sure it’s pointing outwards. You can use a REAR CONNECTOR
to make sure the distance in between the BASES is correct.
Logo
Connect the BASES to each other with the FRONT CONNECTORS.
Start with the FRONT CONNECTOR, this connector connects base at the
front lengthwise. Hand tighten 4 x FLAT HEAD SCREW and 4 x PLASTIC
WASHER. Make sure the BASES and CONNECTORS are flush.
10
11
Plastic washer
Flat head screw

If your Nodi sofa set has a corner you’ll have to use an INNER CORNER
CONNECTOR to connect 3 BASES to each other.
Hand tighten 6 x FLAT HEAD SCREW and 6 x PLASTIC WASHER. Make
sure the BASES and CONNECTORS are flush.
Finaly install the REAR CONNECTOR. Hand tighten 2 x COUNTERSUNK
SCREW. Make sure the BASES and CONNECTORS are flush.
12
13

Every Nodi sofa BASE has adjustable gliders to oppose uneven floors.
Use a level to make sure the BASES are level to each other and horizontal.
Start with the BASE in the corner.
14
Now fully tighten all connector SCREWS.
15

Lay out the backrests so they match your Nodi sofa set.
16
Hand tighten 4/6 x FLAT HEAD SCREW, 4/6 x PLASTIC WASHER, 4/6 x PLASTIC
BUSHING to attach the backrest to the BASE. Start with the corner BACKREST.
17
Plastic washer
Flat head screw
Plastic bushing

Make sure the backrests are aligned with each other, the non woven part
of the backrests should be flush with each other. If that’s the case, tighten
the screws 100 %. You can adjust by the tilting the backrest before full
tightening.
18
When all connectors and backrest are installed, install the INSERTS.
Regular bases will only have exposed corners, which can be filled with
CORNER INSERTS. Lounge or deep bases will also need INSERT Left and
INSERT RIGHT (step )
19
7

Add the plates, make sure the PLATE matches the BASE.
Each PLATE has a logo, match it with the logo on the BASE.
Use COUNTERSUNK SCREWS to attach the plate to the BASE.
Regular plate: 8 x COUNTERSUNK SCREW
Deep plate: 8 x COUNTERSUNK SCREW
Lounge plate: 8 x COUNTERSUNK SCREW
20
After installing the cushions, you can enjoy your Nodi sofa.
21
Logo
Fabric gather
Logo

Tribù nv
Oude Heidestraat 72
3740 Bilzen
BELGIUM
www.tribu.com
[email protected]