TRIBU VIS A VIS 01792 User manual

VIS A VIS SOFA
ASSEMBLY INSTRUCTIONS
PADA01 - 17-05-2022
01792
01708
01738R
01703S
01700
01706L
01738L
01704
01701R
01706R
01709
01703
01701L
01728
01704S
01742
01781
01784
01786
01700B
01701B
01704B
01706B
01709B
01738B
01796B
01797B

COMPONENTS
The elements below are optional:
SEAT SUPPORT
2 - seater
SEAT SUPPORT
1 - seater
LARGE FRAME
2 - seater
SMALL FRAME
1 - seater
LARGE BORDER SMALL BORDER
LEG COFFEE TABLE TOP
LARGE BACK- / ARMREST
HIGH BACKREST COVER
SMALL BACK- / ARMREST
HIGH BACKREST FRAME

To connect the legs to the frame use these 3 components:
WOODSCREW CONNECTOR
CUSTOM BOLT GLIDER SPRING WASHER
WASHER FLATHEAD SCREW
To connect frames to each other use these 2 components:
To connect a backrest to a frame use these 2 components:
ALLEN KEYY - KEY
To secure al components together these tools are provided:

ASSEMBLY INSTRUCTIONS
Put the FRAME upside down on a protective cover. Secure the LEGS to
the FRAME using 1 CUSTOM BOLT and 1 SPRING WASHER per LEG, to
secure them use the Y-KEY. Make sure the SPRING WASHER is placed
between the CUSTOM BOLT and the LEG.
Attach the GLIDERS to the bottem side of the LEGS by turning them
clockwise.
2

Attach the GLIDERS to the bottem side of the LEGS by turning them
clockwise.
3
4
Put the BORDER upside down on a protective cover. Secure the LEGS
to the BORDER using 1 CUSTOM BOLT and 1 SPRING WASHER per LEG,
to secure them use the Y-KEY. Make sure the SPRING WASHER is placed
between the CUSTOM BOLT and the LEG.

Put the FRAMES upside down in the correct composition. Use a rubber
hammer to attach the CONNECTORS to the FRAME. Use 2 CONNECTORS
per connection.
To secure the FRAMES together use
4 WOODSCREWS per CONNECTOR.
Tighten the WOODSSCREWS with a phillips
screwdriver by turning them clockwise.
6
7
If you have a single/double module without BORDERS and no connection
to another module proceed to step 11.
5

Put the FRAME and BORDERS upside down in the correct composition.
Use a rubber hammer to attach the CONNECTORS to the FRAME/BORDER.
Use 2 CONNECTORS per connection.
To secure the FRAME and BORDERS together
use 4 WOODSCREWS per CONNECTOR.
Tighten the WOODSSCREWS with a phillips
screwdriver by turning them clockwise.
8
9

Put the SEAT SUPPORT on its side and slide the BACK- / ARMREST into the
designated holes on the desired position.
10
To secure the BACK- / ARMREST to the SEAT SUPPORT use 2 FLATHEAD
SCREWS and 2 WASHERS per BACK- / ARMREST. Put the WASHER
in between the FLATHEAD SCREW and the SEAT SUPPORT. Turn the
FLATHEAD SCREWS with the ALLEN KEY clockwise to tighten them.
11

Place the assembled SEAT SUPPORTS into the designated FRAME.
12
If a high backrest cushion is also included in your set, skip to step 15.
If not, go to step 14.
13
Slide the pillows over the BACK- / ARMRESTS and put the pillows on
top of the SEAT SUPPORT. When sliding the cushions over the BACK- /
ARMRESTS make sure the side with the most cushioning is facing the sofa.
14

Slide the pillow over the BACK- / ARMRESTS. When sliding the cushions
over the BACK- / ARMRESTS make sure the side with the most cushioning
is facing the sofa.
Then slide the cover over the high backrest frame.
15
16

The high backrest frame can then be placed on the frame of the sofa
against the back cushion.
Now the seat cushions can be placed on the seat support to keep the high
back cushion frame in place.
17
18

Eventually the high back cushion can be placed against that frame.
19

Tribù nv
Oude Heidestraat 72
3740 Bilzen
BELGIUM
www.tribu.com
[email protected]