Trinity 72 inch ROLLING WORKBENCH User manual

OWNER’S MANUAL
72” ROLLING WORKBENCH – STAINLESS STEEL
(Stainless Body)
(Black Body)

You will need 10mm wrench (for handles) and 14mm socket wrench (for casters) for assembly.
PARTS LIST
WORKBENCH (1)
A
SIDE HANDLE (2)
B C
CASTER BOLT (16)
M10
D
LINER (11)
E
GH
HANDLE BOLT (12)
M6
LOCKING CASTER (2)
F
NON-LOCKING
CASTER (2)
KEY (4)
Your 72” Rolling Workbench should include the following parts. Please inspect box contents to ensure
you have received all components.
1
If you are missing any parts, need assistance with assembly or have questions, please contact
Customer Service. Parts can also be requested online via our “Contact Us” section.

ASSEMBLY INSTRUCTIONS
Position SIDE HANDLE (B) over pre-installed nuts on the side of
WORKBENCH (A). Insert HANDLE BOLTS (C) through holes on SIDE
HANDLE (B). Use a 10mm wrench to tighten HANDLE BOLTS (C) to
WORKBENCH (A).
Repeat these instructions to install the other SIDE HANDLE (B).
Location of parts:
1) KEYS (H) are in a plastic bag taped on top
of the CASTERS (D/E) box in the BOTTOM
LEFT Drawer.
NOTE: Drawer lock and cabinet lock
use different keys, please match
code on lock to the code on the key
2) LINERS (G) / SIDE HANDLES (B) /
FASTENERS (C/F) are all in the BOTTOM
RIGHT Drawer.
12
A
B
C
BC
STEP 1
STEP 2
C (12)B (2)10mm
2

ASSEMBLY INSTRUCTIONS
Place LINERS (G) in each drawer and on
each shelf.
D
F
FE
A
G
STEP 3
STEP 4
D (2) E (2) F (16)
G (11)
14mm
Lay WORKBENCH (A) on its backside.
Position LOCKING CASTERS (D) on the side of the
WORKBENCH (A) of your choice and align holes to
pre-installed nuts on the underside of
WORKBENCH (A). Use a 14mm socket wrench to
tighten CASTER BOLT (F) to WORKBENCH (A).
Repeat above step to install the NON-LOCKING
CASTERS (E).
Notes:
* Make sure to install both of the LOCKING
CASTERS (E) on the same side.
** For ease of use, place LOCKING CASTERS (E) on
the side you will regularly push or pull.
*** If you plan to push the Tool Chest against a
wall, place LOCKING CASTERS (E) on the front
long side for ease of access.
3

USAGE INSTRUCTIONS
DRAWER REMOVAL
DRAWER REPLACEMENT
Pull the drawer out so that it is almost fully
extended. On the RIGHT-hand side, push the
black release lever DOWN. On the LEFT-hand
side, pull the black release lever UP. While
holding the levers as instructed, pull the
drawer forward until released from the slides
attached to the Tool Chest (“Tool Chest Slides”).
Note: The slides attached to the drawer
(“Drawer Slides”) are an integral part of the
drawer and must be removed along with the
drawer itself.
To replace the drawer, pull the slides out completely. Insert the brackets on each side of the Drawer
Slides into the corresponding slots on the Tool Chest Slides, making sure they are properly positioned.
Once the brackets are inserted into the slots, completely close the drawer to set all slides in their
proper positions.
SHELF ADJUSTMENT
Ensure all products have been removed
from the shelf.
To adjust the shelf height position, tap
the underside of the shelf, starting on
the right side. Disengage the shelf from
the front and back cabinet tabs first
from the right side and then from the
left.
Tilt the shelf diagonally to move it to the
desired position. Once at the desired
height, secure the shelf by pushing down
on all 4 corners until the shelf engages
fully with the tabs.
Position Tab
4

5
Part Number Description Part Number Description
1) Wood Top 13) Left Door
2) Lock 14) Door Handle
3) Key 15) Non-locking Caster
4) Handle Bolt 16) Slide (drawer side)
5) Side Handle 17) Drawer Handle
6) Small Drawer 18) Handle End Cap
7) Large Drawer 19) Slide (workbench side)
8) Caster Bolt 20) Drawer Liner
9) Locking Caster 21) Shelf Liner
10) Shelf 22) Upper magnet bracket
11) Right Door 23) Lower magnet bracket
12) Door Magnet 24) Bracket screw
NOTE: Replacement keys may be ordered using the code shown on the face of the lock.
The Drawer and Cabinet locks may have different key codes.
5
15
2
6
3
8
16
19
20
21
17 7
14 12 11
1
10
4
9
18
13
22
23
24
SERVICE PARTS LIST
Customer Service provides the following replacement parts:

WARNINGS
1. Read and understand all instructions. Failure to follow all instructions may result in injury
and/or damage.
2. The warnings, cautions, and instructions discussed in this manual cannot cover all
possible conditions or situations that may occur. The user must always be aware of their
environment and ensure that they use the product in a safe and responsible manner.
3. Do NOT modify the product in any way. Unauthorized modification may impair the
function and/or safety of the product, and may affect the life of the product.
4. Check for damaged parts. Before using this product, carefully check that all parts are in
good condition, and that the product will operate properly and perform its intended
function. Check for damaged parts and any other conditions that may affect the operation
of this product. Replace damaged or worn parts, and never use this product with a damaged
part.
5. Do NOT overload the product.
6. Lock the casters when leaving workbench in stationary position.
7. Lock the drawers and cabinet doors before moving the workbench.
8. Do NOT open all drawers at once. Tipping can occur.
CARE AND MAINTENANCE
•Avoid harsh, abrasive cleaners, and other corrosive chemicals.
•Do not use scouring pad for cleaning.
•Keep dry and avoid damp environments.
•Use a quality stainless steel cleaner and follow instructions that come with the cleaner.
Wipe ALONG the grain (NOT against).
•Wood top can be cleaned with damp cloth and wiped dry immediately with dry cloth. If
needed, solvent-based wood furniture cleaner can be used.
•Clean up any spills immediately to prevent stains from forming on the wood top.
Weight capacity per drawer 100 lb
Weight capacity per shelf 75 lb
Total weight capacity of tool chest 1200 lb
6

First Name: Last Name:
Address:
City: State: Zip Code:
Email Address: Phone:
Product Model #: Purchase Date: / /
Location of Purchase:
Please rate the importance of each feature (1=least important; 10=most important)
Quality Price Size/Capacity Appearance Other
How did you hear about our product?
Magazine Ad Catalog Salesperson Word of Mouth
Internet Store Display Other
Marital Status: Single Married
Household Income: Below $50,000 $50,000-$150,000 $150,000+
Education: High School College Graduate School
Primary Residence: Own Rent
Comments/Suggestions:
PRODUCT REGISTRATION
Thank you for purchasing this 72” Rolling Workbench. In order to register your product and receive
streamlined customer service, please fill out the following Product Registration Form and (1)
fax the form (2) complete the Product Registration Form online or (3) scan and email the form. Include
a copy of your original receipt with your submission.
8

QUESTIONS? NEED PARTS?
WE ARE HERE TO HELP!
Please feel free to contact us. There are no questions too small, or
any problems too big. We’re committed to providing our customers
with the highest level of service.
CONTACT US