Trinity TLS-4815 User manual

OWNER’S MANUAL
Important / Important / Importante
DOWNLOAD THE FREE APP | TÉLÉCHARGER L’APPLICATION GRATUITE| DESCARGUE LAAPLICACIÓN GRATUITA
Directives intelligentes
Instrucciones Inteligentes
FOR QUICK & EASY 3D ASSEMBLY INSTRUCTIONS
POUR DES DIRECTIVES D’ASSEMBLAGE 3D RAPIDES ET FACILES
PARA INSTRUCCIONES DE ENSAMBLAJE RAPIDAS Y SENCILLAS EN 3D
TRINITY 7-DRAWER 48”W x 26”D STAINLESS STEEL WORKBENCH
Model # TLS-4815

Your TRINITY 7-Drawer 48”W x 26”D Stainless Steel Workbench should include the following parts.
Please inspect box contents to ensure you have received all components.
If you are missing any parts, need assistance with assembly or have questions, please contact TRINITY
Customer Service: 800.985.5506 or [e-mail]. Parts can also be requested online
via “Contact Us” section at www.trinityii.com.
You will need 10mm wrench (for handles) and 14mm wrench (for casters) for assembly. Not included.
A
SIDE HANDLE (2)
BC
CASTER BOLT (16)
M10
D
LINER (7)
EGH
HANDLE BOLT (12)
M6 LOCKING
CASTER (2)
F
NON-LOCKING
CASTER (2) KEY (2)
© 2021 TRINITY - 800.985.5506
1
WORKBENCH (1)
PARTS LIST

ASSEMBLY INSTRUCTIONS
Position SIDE HANDLE (B) over pre-installed nuts on side of
WORKBENCH (A). Insert HANDLE BOLTS (C) through holes on
SIDE HANDLE (B). Use a 10mm socket wrench to fully tighten
HANDLE BOLTS (C) to WORKBENCH (A).
Repeat above steps to install remaining SIDE HANDLE (B).
AB
C
© 2021 TRINITY - 800.985.5506 2
STEP 1
STEP 2
Location of parts:
1) KEYS (H) are hooked on the key leash that is
mounted in the TOP LEFT Drawer.
2) CASTERS (D/E) and CASTER BOLTS (F) /
LINERS (G) / SIDE HANDLES (B) and HANDLE
BOLTS (C) are all in the BOTTOM Drawer.
B
C
C (12) 10mm
B (2)
A (1)
2
1

ASSEMBLY INSTRUCTIONS
© 2021 TRINITY - 800.985.5506
3
STEP 3
Lay WORKBENCH (A) on its backside. Two people
are needed. Do NOT attempt this alone.
Position LOCKING CASTERS (D) on side of
WORKBENCH (A) of your choice and align holes to
pre-installed nuts on underside of WORKBENCH
(A). Use a 14mm socket wrench to fully tighten
CASTER BOLT (F) to WORKBENCH (A).
Repeat to install NON-LOCKING CASTERS (E).
Notes:
* Make sure to install both LOCKING CASTERS (D)
on same side.
** For ease of use, place LOCKING CASTERS (D) on
side you will regularly push or pull.
*** If you plan to push workbench against a wall,
place LOCKING CASTERS (D) on front long side for
ease of access.
A
Carefully lift WORKBENCH (A) upright. Two people
are needed. Do NOT attempt this alone.
Place LINERS (G) in each drawer. G (7)
STEP 4
E
D
F
G
A
F (16) 14mm
E (2)
D (2)

USAGE INSTRUCTIONS
DRAWER REMOVAL
DRAWER REPLACEMENT
© 2021 TRINITY - 800.985.5506 4
To replace drawer, pull slides out completely. Insert brackets on each side of Drawer Slides into
corresponding slots on the Workbench Slides, making sure they are properly positioned. Once brackets
are inserted into the slots, completely close the drawer to set all slides in their proper positions.
Pull drawer out so that it is almost fully extended. On RIGHT-hand side, pull black release lever UP. On
LEFT-hand side, push black release lever DOWN. While holding levers as instructed, pull drawer
forward until released from the slides attached to Workbench (“Workbench Slides”).
Note: The slides attached to drawer (“Drawer Slides”) are an integral part of drawer and must be
removed along with drawer itself.

Part Number Description Part Number Description
1) LNA-06-001-4826 Wood Top 13) XBK-22-001-2618 26” Drawer Liner
2) ZSV-01-001-0612 Handle Bolt 14) XBK-22-001-4318 43” Drawer Liner
3) XSV-05-001-1100 Side Handle 15) ZSV-99-002-5020 Non-locking Caster
4) XBS-07-012-1503 15” Small Drawer 16) XBS-07-012-4409 44” Large Drawer
5) AMA-05-019-1400 14” Drawer Handle 17) AMA-05-019-4300 43” Drawer Handle
6) XBS-07-012-1509 15” Large Drawer 18) XBS-07-012-2706 27” Large Drawer
7) ZSV-12-002-2175 Slide (workbench side) 19) ZSV-12-001-2175 Slide (Drawer side)
8) XBS-07-012-4403 44” small Drawer 20) AMA-05-019-2600 26” Drawer Handle
9) XBK-23-007-2512 End Cap 21)XBS-07-012-2703 27” Small Drawer
10) ZSV-99-001-5020 Locking Caster 22) CSV-11-001-0XXX Lock
11) ZSV-01-001-1020 Caster Bolt 23) XBK-02-047-0001 Key leash
12) XBK-22-001-1418 14” Drawer Liner
24)
XBK-10-001-0XXX Key
SERVICE PARTS LIST –TLS-4815
TRINITY Customer Service provides the following replacement parts:
4
5
1
7
2
12
18
16 10
17
19
NOTE: Replacement keys may be ordered using the code shown on the face of the lock.
8
21 3
15
20
6
22
11
23
13
14
9
© 2021 TRINITY - 800.985.5506
5
24

WARNINGS
1. Read and understand all instructions. Failure to follow all instructions may result in injury
and/or damage.
2. The warnings, cautions, and instructions discussed in this manual cannot cover all
possible conditions or situations that may occur. The user must always be aware of their
environment and ensure that they use the product in a safe and responsible manner.
3. Do NOT modify the product in any way. Unauthorized modification may impair the
function and/or safety of the product, and may affect the life of the product.
4. Check for damaged parts. Before using this product, carefully check that all parts are in
good condition, and that the product will operate properly and perform its intended
function. Check for damaged parts and any other conditions that may affect the operation
of this product. Replace damaged or worn parts, and never use this product with a
damaged part.
5. Do NOT overload the product.
6. Lock the casters when leaving workbench in stationary position.
7. Lock the drawers before moving the workbench.
8. Do NOT open more than one drawer at a time. Tipping can occur.
9. Do NOT step or lean on open drawers. Tipping can occur.
10. Do NOT let children play near workbench.
11. Load the workbench starting with the bottom drawers to prevent workbench from
tipping.
13. Make sure all drawers are closed tightly before locking or unlocking.
Weight capacity per drawer w/ 1 pair of slide 100 lb
Weight capacity per drawer w/ 2 pairs of slide 200 lb
Total weight capacity of workbench 2200 lb
© 2021 TRINITY - 800.985.5506 6

CARE AND MAINTENANCE
•Avoid harsh, abrasive cleaners, and other corrosive chemicals.
•Do not use scouring pad for cleaning.
•Keep dry and avoid damp environments.
•Use a quality stainless steel cleaner and follow instructions that come with the cleaner.
Wipe ALONG the grain (NOT against).
•Wood top can be cleaned with damp cloth and wiped dry immediately with dry cloth. If
needed, solvent-based wood furniture cleaner can be used.
•Clean up any spills immediately to prevent stains from forming on the wood top.
© 2021 TRINITY - 800.985.5506
7

Thank you for purchasing a TRINITY 7-Drawer 48”W x 26”D Stainless Steel Workbench. In order to
register your product and receive streamlined customer service, please fill out the following Product
Registration Form and (1) fax the form to 310.347.4134 (2) complete the Product Registration Form
online at www.trinityii.com or (3) scan and email the form to [e-mail]. Include a
copy of your original receipt with your submission.
First Name: Last Name:
Address:
City: State: Zip Code:
Email Address: Phone:
Product Model #: TLS-4815 Purchase Date: / /
Location of Purchase:
Please rate the importance of each feature (1=least important; 10=most important)
Quality Price Size/Capacity Appearance Other
How did you hear about our product?
Magazine Ad Catalog Salesperson Word of Mouth
Internet Store Display Other
Marital Status: Single Married
Household Income: Below $50,000 $50,000-$150,000 $150,000+
Education: High School College Graduate School
Primary Residence: Own Rent
Comments/Suggestions:
PRODUCT REGISTRATION
© 2021 TRINITY - 800.985.5506 8

© 2021 TRINITY - 800.985.5506
9