Trinity Pro TLSF-7210 User manual

TRINITY PRO 72” 10-DRAWER STAINLESS STEEL
WORKBENCH W/ PEGBOARD
Model # TLSF-7210
OWNER’S MANUAL

Your TRINITY PRO 72in 10-Drawer Stainless Steel Workbench w/ Pegboard should include the following
parts. Please inspect box contents to ensure you have received all components.
If you are missing any parts, need assistance with assembly or have questions, please contact TRINITY
Customer Service: 800.985.5506 or [e-mail]. Parts can also be requested online at
www.trinityii.com (Help & More, Contact Us).
You will need 10mm wrench (for handles), 14mm wrench (for casters) and 12mm wrench (for pegboard)
for assembly. These are NOT included.
A
SIDE HANDLE (2)
BC
CASTER BOLT (16)
M10
D
LINER (10)
E G H
HANDLE BOLT (12)
M6 LOCKING CASTER (2)
F
NON-LOCKING
CASTER (2) KEY (2)
WORKBENCH
w/PEGBOARD (1)
PARTS LIST
SMALL BIN (6) MEDIUM BIN (2) LARGE BIN (1) HOOK (10)
© 2018 TRINITY - 800.985.5506 1
I K LJ

ASSEMBLY INSTRUCTIONS
Position SIDE HANDLE (B) over pre-installed nuts on side of
WORKBENCH (A). Insert HANDLE BOLTS (C) through holes on
SIDE HANDLE (B). Use a 10mm socket wrench to fully tighten
HANDLE BOLTS (C) to WORKBENCH (A).
Repeat above steps to install remaining SIDE HANDLE (B).
A
B
C
STEP 1
STEP 2
10mmA (1) B (2) C (12)
Location of parts:
1) KEYS (H) are in a plastic bag taped on top of
the CASTERS (D/E/F) box in BOTTOM LEFT
Drawer.
2) LINERS (G) / SIDE HANDLES (B) and HANDLE
BOLTS (C) / BINS (I/J/K) and PEGS (L) are all in
BOTTOM RIGHT Drawer.
12
B
C
© 2018 TRINITY - 800.985.5506
2

ASSEMBLY INSTRUCTIONS
STEP 3
D (2) E (2) F (16)
Lay WORKBENCH (A) on its backside. Lift
workbench by side handles. Do NOT lift
workbench by the wood top. Two people are
needed. Do NOT attempt this alone.
Position LOCKING CASTERS (D) on side of
WORKBENCH (A) of your choice and align holes to
pre-installed nuts on underside of WORKBENCH
(A). Use a 14mm socket wrench to fully tighten
CASTER BOLT (F) to WORKBENCH (A).
Repeat above steps to install NON-LOCKING
CASTERS (E).
Notes:
* Make sure to install both LOCKING CASTERS (D)
on same side of workbench.
** For ease of use, place LOCKING CASTERS (D) on
side you will regularly push or pull.
*** If you plan to push the workbench against a
wall, place LOCKING CASTERS (D) on front long
side for ease of access.
14mm
A
Place LINERS (G) in each drawer.
DO NOT place liner in TOP LEFT or TOP RIGHT
drawer which already has a wood work surface
installed inside.
STEP 4
ED
F
G (10)
G
© 2018 TRINITY - 800.985.5506 3

ASSEMBLY INSTRUCTIONS
STEP 5
Two people are needed for this step. Do NOT
attempt this alone.
Unscrew bottom Bolt on both left and right hand
side of Pegboard with a 12mm socket wrench. Lift
Pegboard upright. With one person holding the
Pegboard in place, have the other person insert
the bottom Bolt into the top hole of each bracket.
Tighten both Bolts fully back to the Pegboard with
wrench.
BOTTOM BOLT
TOP HOLE
BRACKET
PEGBOARD
BOTTOM BOLT
12mm
© 2018 TRINITY - 800.985.5506
4

ASSEMBLY INSTRUCTIONS
STEP 6
Hang SMALL/MEDIUM/LARGE BINS (I/J/K) over four
rectangular hollow sections on top of pegboard as
shown.
Hang HOOKS (L) into holes on pegboard at your
desired location.
L (10)
I (6) J (2) K (1)
© 2018 TRINITY - 800.985.5506 5

USAGE INSTRUCTIONS
DRAWER REMOVAL
DRAWER REPLACEMENT
Pull drawer out so that it is almost fully extended. On RIGHT-hand side, push black release lever DOWN.
On LEFT-hand side, pull black release lever UP. While holding levers as instructed, pull drawer forward
until released from the slides attached to Workbench (“Workbench Slides”).
Note: The slides attached to drawer (“Drawer Slides”) are an integral part of drawer and must be
removed along with drawer itself.
To replace drawer, pull slides out completely. Insert brackets on each side of Drawer Slides into
corresponding slots on the Workbench Slides, making sure they are properly positioned. Once the
brackets are inserted into the slots, completely close the drawer to set all slides in their proper positions.
© 2018 TRINITY - 800.985.5506
6

USAGE INSTRUCTIONS
ENGAGE STOPPER
DISENGAGE STOPPER
Pull top left or right drawer out so it is almost fully extended. Engage stopper on back corner of each
side of drawer by turning it up, making sure stopper rests over drawer frame. Ensure both stoppers are
engaged when work surface is being used.
Disengage stopper by turning it inside drawer. Make sure stopper lays flat on work surface before
pushing drawer back into workbench.
STOPPER
STOPPER
© 2018 TRINITY - 800.985.5506 7

SERVICE PARTS LIST –TLSF-7210
Part Number Description Part Number Description
1) XGR-21-007-0605 Medium Bin 17) XBK-10-003-0XXX Key
2) XDG-21-007-1205 Large Bin 18) XBK-22-006-1415 15” Drawer Liner
3) XBS-15-014-6428 Pegboard 19) XBK-22-006-2615 27” Drawer Liner
4) XSV-01-009-0816 Pegboard Bolt 20) XBS-07-009-2709 27” Large Drawer
5) XBS-19-008-0825 Bracket 21) ZSV-99-028-5020 Non-locking Caster
6) XSV-01-027-0816 Bracket Screw 22) XBS-07-009-1509 15” 2nd Medium Drawer
7) XSV-05-001-0900 Side Handle 23) AMA-05-007-1400 15” Drawer Handle
8) ZSV-01-001-0612 Handle Bolt 24) XBK-23-010-3012 End cap
9) XBK-02-024-0001 Stopper 25)XBS-07-009-2706 27” Medium Drawer
10) LNA-06-014-1514 Work Surface 26) AMA-05-007-2600 27” Drawer Handle
11) XBS-07-009-1506 15” 1st Medium Drawer 27) XBS-07-009-1503 15” Small Drawer
12) XBS-07-009-1512 15” Large Drawer 28) XBS-07-009-2703 27” Small Drawer
13) ZSV-01-001-1020 Caster Bolt 29) CSV-11-005-0XXX Lock
14) ZSV-99-027-5020 Locking Caster 30) LNA-06-013-7219 Wood Top
15) ZSV-12-002-1575 Slide (workbench side) 31) ZSV-02-025-0001 Hook
16) ZSV-12-001-1575 Slide (drawer side)
32)
XOR-21-007-0403 Small Bin
TRINITY Customer Service provides the following replacement parts:
© 2018 TRINITY - 800.985.5506
8