Triton RL5000 (X2) User manual

TDN 07100-00092B
THIS AREA FOR SERVICE PROVIDER
CONTACT INFORMATION:
Jan 29 2009
Model RL5000 (X2)
QUICK REFERENCE GUIDE

2
MANAGEMENT FUNCTIONS
- ACCESS INSTRUCTIONS -
1. AT ATM WELCOME SCREEN, PRESS AND HOLD DOWN THE <CTRL>
KEY (LOWER-RIGHT CORNER OF KEYPAD), PRESS <1> KEY, THEN RE-
LEASE BOTH KEYS. THE PASSWORD A CCESS PROMPT IS DISPLAYED.
2. ENTER PASSWORD AND SELECT <ENTER>. THE MANAGEMENT FUNCTIONS MAIN MENU IS DISPLAYED.
TERMINAL CONFIGURATION REPORT
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT DIAGNOSTICS > TERMINAL STATUS.
CONFIGURATION SUMMARY: THIS SUMMARY IS A COMPREHENSIVE
REPORT OF CURRENT TERMINAL CONFIGURATION AND HARDWARE STATUS IN-
FORMATION.
NOTE: IT IS HIGHLY RECOMMENDED THAT THIS REPORT BE PRINTED AND SAVED AFTER INITIAL SETUP AND WHENEVER
CHANGES ARE MADE TO THE TERMINALS CONFIGURATION.
RESTART / SHUTDOWN TERMINAL
RESTART TERMINAL: THIS FUNCTION REBOOTS THE TERMINAL.
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT SYSTEM PARAMETERS.
SHUTDOWN TERMINAL: THIS FUNCTION POWERS-DOWN THE TERMI-
NALS OPERATING SYSTEM. WHEN PROMPTED THAT SHUTDOWN IS COMPLETE,
TURN ON/OFF SWITCH ON POWER SUPPLY TO <OFF> POSITION.

3
DIAGNOSTICS
PURGE: THIS INSTRUCTS THE DISPENSER TO REMOVE ANY NOTES (JAMS) IN
FEED PATH.
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT DIAGNOSTICS > DISPENSER.
TEST DISPENSE: THIS INSTRUCTS THE DISPENSER TO DISPENSE MINIMUM
ONE NOTE FROM EACH INSTALLED CASSETTE INTO THE REJECT CASSETTE/
AREA.
RESET / TEST PRINTER: THIS
INSTRUCTS THE PRINTER TO RE-INI-
TIALIZE AND PERFORM A TEST PRINT-
OUT.
SELECT DIAGNOSTICS > PRINTER.
PRINT LAST X: TO VIEW/PRINT PREVIOUSLY AUDITED OR UNAUDITED
RECORDS, USE THE PRINT LAST X OPTION.
JOURNAL FUNCTIONS
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT JOURNAL.
EXAMPLE: ENTERING THE NUMBER ‘50’ WILL LET YOU VIEW THE LAST 50 TRANSACTIONS/EVENTS THAT HAVE OC-
CURRED. YOU MAY PRINT TO THE RECEIPT PRINTER.
DAY CLOSE: THIS OPTION IS USED TO COMPLETE DAILY BALANCING OF THE
ATM WITH THE PROCESSOR. TOTALS ARE CLEARED AND SWITCHED TO THE
NEXT BUSINESS DAY.
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT TERMINAL CLOSE FUNCTIONS.
TRIAL CLOSE: THIS OPTION FUNCTIONS LIKE A DAY CLOSE EXCEPT THE TOTALS ARE NOT CLEARED.
CLOSE FUNCTIONS

4
CASSETTE CLOSE FUNCTIONS
FOLLOW A CCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SELECT TERMINAL CLOSE FUNCTIONS.
SELECT CASSETTE CLOSE.
SELECT CASSETTE(S) TO CLOSE. A CHECK MARK (√√
√√
√ ) IDEN-
TIFIES WHICH CASSETTE(S) ARE SELECTED. PRESS <ENTER>.
NOTE: IF AN NMD-50 DISPENSER IS INSTALLED, WAIT FOR THE
CASSETTES TO UNLOCK (THIS IS DONE AUTOMATICALLY).
REMOVE AND REPLENISH THE SELECTED CASSETTE(S).
PROCEDURES FOR SPECIFIC DISPENSING MECHANISMS CAS-
SETTE REPLENISHMENT ARE ON THE FOLLOWING PAGES.
PLACE SELECTED CASSETTE(S) IN SERVICE. PRESS <EN-
TER>. NOTE: SINGLE CASSETTE DISPENSERS (TDM-100/150,
SDD)AUTOMATICALLY “IN-SERVICE”. THE NMD-50CASSETTES
MUST BE LOCKED AND INSERVICE FOR NORMAL OPERATION.
NOTE: IF AN NMD-50 DISPENSER IS INSTALLED, WAIT FOR THE
CASSETTES TO LOCK (THIS IS DONE AUTOMATICALLY). PRESS
<ENTER> IF APPLICABLE.
ENTER CASSETTE QUANTITY (NUMBER OF NOTES, NOT
VALUE) FOR THE SELECTED CASSETTE(S). PRESS <ENTER> TO AC-
CEPT ENTRY. REPEAT FOR EACH SELECTED CASSETTE.
A CLOSE REPORT IS DISPLAYED TO BE PRINTED OR SAVED.
THIS OPERATION WILL RESET THE NUMBER OF BILLS IN THE
CASSETTE(S) TO ZERO (0). PRESS <ENTER>.
AFTER CASSETTE(S) HAVE BEEN REINSERTED IN THE DISPENSER,
PRESS <ENTER>.
A TRIAL CASSETTE CLOSE REPORT AUTOMATICALLY
IS DISPLAYED TO BE PRINTED OR SAVED. PRINT AND RETAIN A
COPY FOR STARTING POINT REFERENCE. PRESS <ENTER> TO RE-
TURN TO CLOSE FUNCTIONS.

5
REMOVE THE NOTE CASSETTE. UNLOCK AND MOVE PACKER
PLATE TO REAR OF THE CASSETTE. LATCH IN PLACE WITH
THE HOLD-BACK LATCH.
LOCATE THE SPRING-LOADED LOCKING PIN ON UNDER-
SIDE OF TRAY. PULL PIN DOWN AND ROTATE SWIVEL
PLATFORM 180° CLOCKWISE. RELEASE PIN TO LOCK IN
PLACE.
3
1
2
4
6
STEP ACTION
5
UNLOCK/OPEN DISPENSER SECURITY DOOR. (FOR TDM-
150) RELEASE THE SLIDE LOCKING LEVER AND EXTEND
STEP ACTION
NOTE: TDM-150 IS ON A SLIDING MOUNTING TRAY.
TDM-100 IS ON A STATIONARY TRAY.
COUNT THE NUMBER OF BILLS THAT REMAIN IN THE CAS-
SETTE, IF ANY.
COUNT THE NUMBER OF BILLS THAT ARE BEING ADDED TO
THE REMAINING NOTES.
THE TOTAL OF THESE AMOUNTS WILL BE ENTERED IN
THE “ENTER CASSETTE QUANTITY” PROMPT FOR CAS-
SETTE CLOSE PROCEDURE.
REPLENISH TDM CASSETTE
(TDM-100, -150)
REMOVE REJECT CASSETTE. UNLOCK AND REMOVE ANY
NOTES. DO NOT RECYCLE REJECTED NOTES!
CLOSE AND LOCK REJECT CLOSE AND REINSTALL IN DIS-
PENSER.
PLACE CURRENCY IN THE CAS-
SETTE AND SLOWLY RELEASE THE
HOLD-BACK LATCH ALLOWING
THE PACKER PLATE TO MOVE
FORWARD AGAINST THE NOTES.
SLIDE THE CASSETTE BACK INTO THE DISPENSER.
PULL THE LOCKING PIN DOWN AND ROTATE SWIVEL PLAT-
FORM 180° COUNTERCLOCKWISE. RELEASE PIN TO LOCK
IN PLACE.
THE DISPENSER MOUNTING
TRAY FULLY.
(FOR TDM-150) R E-
LEASE THE SLIDE LOCKING
LEVER AND SLIDE DIS-
PENSER TRAY FULLY IN THE
CABINET.

6
UNLOCK/OPEN DISPENSER
SECURITY DOOR. RELEASE
THE SLIDE LOCKING LEVER
AND EXTEND THE DISPENSER
MOUNTING TRAY FULLY.
REMOVE REJECT CASSETTE.
UNLOCK AND REMOVE ANY
NOTES. DO NOT RE-
CYCLE REJECTED NOTES!
CLOSE AND LOCK REJECT
CLOSE AND REINSTALL IN
DISPENSER.
3
1
2
6
STEP ACTION
5
PLACE CURRENCY IN THE CAS-
SETTE AND SLOWLY RELEASE THE
HOLD-BACK LATCH ALLOWING
THE PACKER PLATE TO MOVE
FORWARD AGAINST THE NOTES.
REPLENISH TDM CASSETTE(S)
(TDM-200, -250)
LOCATE THE SPRING-
LOADED LOCKING PIN ON
UNDERSIDE OF TRAY. PULL
PIN DOWN AND ROTATE
SWIVEL PLATFORM 180°
CLOCKWISE. RELEASE PIN
TO LOCK IN PLACE.
STEP ACTION
REMOVE THE NOTE
CASSETTE(S). UNLOCK AND
MOVE PACKER PLATE TO
REAR OF THE CASSETTE.
LATCH IN PLACE WITH THE
HOLD-BACK LATCH.
Reject cassette
Note cassettes
4
COUNT THE NUMBER OF BILLS THAT REMAIN IN THE CAS-
SETTE, IF ANY.
COUNT THE NUMBER OF BILLS THAT ARE BEING ADDED TO
THE REMAINING NOTES.
THE TOTAL OF THESE AMOUNTS WILL BE ENTERED IN
THE “ENTER CASSETTE QUANTITY” PROMPT FOR CAS-
SETTE CLOSE PROCEDURE.
SLIDE THE CASSETTE BACK INTO THE DISPENSER.
PULL THE LOCKING PIN DOWN AND ROTATE SWIVEL PLAT-
FORM 180° COUNTERCLOCKWISE. RELEASE PIN TO LOCK IN
PLACE.
RELEASE THE SLIDE LOCKING LEVER AND SLIDE DISPENSER
TRAY FULLY IN THE CABINET.

7
7
SLIDE CASSETTE ON TO THE LOADING TRAY. LIFT LID TO
EXPOSE THE REJECT TRAY. REMOVE ANY REJECT NOTES.
DO NOT RECYCLE REJECTED NOTES!
3
1
2
4
6
LIFT THE REJECT TRAY.
PUSH THE PACKER PLATE
TO REAR OF CASSETTE AND
LATCH IN PLACE.
CASSETTE MUST BE PRIMED WITH THE CASSETTE
KEY BEFORE INSERTING ON THE LOADING TRAY. INSERT
KEY AND TURN CLOCKWISE TO SHOW GREEN INDICA-
TOR IN WINDOW.5
REPLENISH SDD CASSETTE
UNLOCK/OPEN DISPENSER
SECURITY DOOR. G RASP
THE CASSETTE HANDLE AND
REMOVE THE CASSETTE.
STEP ACTION
Cassette “primed”
Green window
STEP ACTION
COUNT THE NUMBER OF BILLS THAT REMAIN IN THE CAS-
SETTE, IF ANY.
COUNT THE NUMBER OF BILLS THAT ARE BEING ADDED TO
THE REMAINING NOTES.
THE TOTAL OF THESE AMOUNTS WILL BE ENTERED IN THE
“ENTER CASSETTE QUANTITY” PROMPT FOR CASSETTE
CLOSE PROCEDURE.
PLACE CURRENCY IN THE
CASSETTE AND SLOWLY RE-
LEASE THE HOLD-BACK
LATCH ALLOWING THE
PACKER PLATE TO MOVE
FORWARD AGAINST THE
NOTES. CLOSE THE CAS-
SETTE LID.
REMOVE CASSETTE FROM
LOADING TRAY. INSERT THE
CASSETTE KEY AND
“PRIME” THE CASSETTE
(“GREEN” INDICATOR).
INSTALL THE CASSETTE INTO
THE DISPENSER.
***WARNING***
IF RED IS INDICATED IN THE WINDOW ON THE SIDE
OF THE CURRENCY CASSETTE, NEVER ATTEMPT
TO INSERT THE CASSETTE INTO THE DISPENSER OR
THE LOADING TRAY!

8
MOVE THE PACKER PLATE TOWARDS THE REAR.
3
1
2
6
PRESS THE GREEN RELEASE BUTTON AND LIFT THE LID.
FLIP THE LID BACK FULLY LETTING IT REST ON A FLAT
SURFACE.
5
REPLENISH NMD-50 CASSETTE(S)
UNLOCK/OPEN DISPENSER SECURITY DOOR. GRASP CAS-
SETTE HANDLE WITH ONE HAND WHILE HOLDING MECHA-
NISM WITH THE OTHER.
STEP ACTION
STEP ACTION
4
7
PULL CASSETTE OUT
SLIGHTLY, THEN PLACE
ONE HAND UNDER-
NEATH. REMOVE CAS-
SETTE.PLACE CURRENCY IN THE
CASSETTE AND MOVE
PACKER PLATE AGAINST THE
NOTES.
COUNT THE NUMBER OF BILLS THAT REMAIN IN THE CAS-
SETTE, IF ANY.
COUNT THE NUMBER OF BILLS THAT ARE BEING ADDED
TO THE REMAINING NOTES.
THE TOTAL OF THESE AMOUNTS WILL BE ENTERED IN
THE “ENTER CASSETTE QUANTITY” PROMPT FOR CAS-
SETTE CLOSE PROCEDURE.
EXTEND THE “PAWLS” ON
PACKER PLATE FULLY.
CLOSE LID AND INSTALL IN
DISPENSER.
REMOVE REJECT VAULT.
OPEN VAULT BY ROTATING
GREEN RELEASE LEVER
“COUNTERCLOCKWISE”.
GRASP LID AND OPEN. RE-
MOVE ANY REJECTED
NOTES. DO NOT RE-
CYCLE REJECTED NOTES!
ROTATE GREEN RELEASE
LEVER AGAIN AND CLOSE
LID. INSTALL REJECT VAULT
IN DISPENSER.

9
14
2
5
36
STEP ACTION
REPLENISH RECEIPT PAPER
STEP ACTION
PULL RELEASE
PIN AND ROTATE
PRINTER/CUT-
TER ASSEMBLY
DOWN.
INSTALL NEW PA-
PER ROLL/ SPINDLE
IN BRACKET.
PAPER FEEDS
FROM TOP OF
ROLL!
FEED END OF PAPER INTO PRINTER TAKE-UP SLOT.
PAPER FEEDS OVER THE BAR! PRINTER WILL
AUTOMATICALLY GRIP AND PULL PAPER INTO
FEED PATH.
NOTE: THIS PROCEDURE REQUIRES TERMINAL IS POWERED UP.
REMOVE SPENT
PAPER ROLL AND
SPINDLE FORM PA-
PER BRACKET.
OPEN CONTROL PANEL. IF PAPER REMAINS ON
ROLL, CUT OR TEAR PAPER BETWEEN ROLL AND
PRINTER.
RELEASE (OPEN) THE BLUE TENSION LEVER SHOWN.
REMOVE ANY PAPER FROM THE PRINTER/CUTTER
ASSEMBLY.
Open
Closed
MOVE THE TENSION
LEVER BACK TO THE
CLOSED POSITION.
ROTATE UP THE
PRINTER/CUTTER AS-
SEMBLY.
RECOMMEND PERFORM A DIAGNOSTIC TEST OF
THE PRINTER. GO TO MAIN MENU > DIAG-
NOSTICS > PRINTER > RESET/TEST
PRINTER. T HIS FUNCTION RE-INITIALIZES
AND PERFORMS AN OPERATIONAL TEST OF THE
PRINTER.

10
COMBINATION LOCKS
INTRODUCTION
THE SECURITY CABINET CAN BE SECURED USING AN ELECTRONIC COMBINATION LOCK. THESE
PAGES COVER HOW TO OPERATE THE COMBINATION OF EITHER ELECTRONIC LOCK OFFERED.
ENTERING THE COMBINATION
1. ENTER THE PRESET COMBINATION AND CHECK FOR PROPER OPERATION. AFTER EACH KEYPRESS, THE LOCK WILL BEEP. AFTER THE
FINAL DIGIT HAS BEEN ENTERED, THE LOCK WILL BEEP TWICE, AND THE OPEN PERIOD WILL BEGIN.
2. WHEN A VALID COMBINATION HAS BEEN ENTERED, THE OPERATOR WILL HAVE APPROXIMATELY 4SECONDS TO OPEN THE LOCK.
3. TO OPEN THE LOCK, TURN THE DIAL CLOCKWISE.
4. AFTER THE LOCK IS OPENED, THE CABINET DOOR MAY BE OPENED.
LOCKOUT FEATURE
THE LOCK INCLUDES A ‘WRONG TRY PENALTY’ LOCKOUT FEATURE THAT PREVENTS ENTRY FROM UNAUTHORIZED PERSONNEL. THIS
FEATURE PERFORMS AS FOLLOWS:
•ENTRY OF FOUR (4) CONSECUTIVE INVALID COMBINATIONS STARTS A 5-MINUTE DELAY PERIOD.
- LED FLASHES RED AT TEN (10) SECOND INTERVALS.
•AT THE END OF THE DELAY PERIOD, TWO (2) MORE CONSECUTIVE INVALID COMBINATIONS WILL RESTART AN ADDITIONAL 5-MINUTE
DELAY.
EACH LOCK IS SHIPPED FROM THE FACTORY IN SHELVED MODE, OPERATING ON A STANDARD COMBINATION (50-25-50).
ENTERING THE COMBINATION
1. TURN THE DIAL LEFT (CCW) UNTIL THE LETTERS “EC” (ENTER COMBINATION) APPEAR
ON THE LCD.
2. ENTER THE FACTORY COMBINATION OF 50-25-50 BY SEQUENTIALLY PRESSING THOSE SIX
(6) BUTTONS. THE LCD WILL DISPLAY THESE NUMBERS AS THEY ARE ENTERED.
3. WHEN THE COMBINATION HAS BEEN CORRECTLY ENTERED, THE LCD WILL READ “OPR”,
MEANING “OPEN RIGHT”. TURN THE DIAL RIGHT (CW) UNTIL IT STOPS. THE LOCKS
BOLT IS NOW RETRACTED AND THE LOCK IS OPEN.
4. AFTER THE LOCK IS OPENED, THE CABINET DOOR MAY BE OPENED.
OPERATING THE ELECTRONIC LOCK
THE ELECTRONIC LOCK COMBINATION CONSISTS OF SIX DIGITS. UPON ARRIVAL, THE COMBINA-
TION OF THE LOCK SHOULD ALREADY BE PRESET TO 1-2-3-4-5-6.

11
11. CNF - ENTER NEW COMBINATION - POC
ENTER NEW COMBINATION AGAIN TO CONFIRM. POC (PULL OUT CHANGE KEY) WILLBE DISPLAYED.
12. POC - REMOVE CHANGE KEY - EOP
REMOVE THE CHANGE KEY. EOP (END OPERATION) IS DISPLAYED.
13. EOP - P
OWER LOCK - EC
TURN THE DIAL TO THE LEFT (CCW) UNTIL EC (ENTER COMBINATION) IS DISPLAYED.
14. EC - ENTER NEW SHELVED MODE COMBINATION - OPR
ENTER THE NEW SHELVED MODE COMBINATION BY PRESSING THOSE DIGITS ON THE LOCK’S KEYPAD. THE NUMBERS WILL BE DISPLAYED
ON THE LCD AS THEY ARE ENTERED.
15. OPR - RETRACT BOLT
TURN THE DIAL TO THE RIGHT (CW) TO RETRACT THE BOLT.
16. CLOSE DOOR
17. EXTEND BOLT
TURN THE DIAL TO THE LEFT (CCW) TO EXTEND THE BOLT.
10. ENF - ENTER NEW COMBINATION - CNF
SELECT AND ENTER THE NEW COMBINATION. “CNF” (CONFIRM NEW FACTORY COMBINATION) WILL BE DISPLAYED.
TO CHANGE THE COMBINATION:
1. POWER LOCK - EC
TURN THE DIAL TO THE LEFT (CCW) UNTIL “EC” (ENTER COMBINATION) IS DISPLAYED.
2. EC - ENTER SHELVED MODE COMBINATION - OPR
ENTER THE CURRENT COMBINATION (EITHER 50-25-50 OR A CHANGED COMBINATION) BY SEQUENTIALLY PRESSING THOSE DIGITS ON
THE LOCK KEYPAD. THE NUMBERS WILL BE DISPLAYED ON THE LCD AS THEY ARE ENTERED.
3. OP
R - RETRACT BOLT
TURN THE DIAL TO THE RIGHT (CW) TO RETRACT THE BOLT
4. OPEN DOOR
5. INSERT CHANGE KEY
INSERT THE CHANGE KEY INTO THE CHANGE KEY SOCKET ON THE BACK OF THE LOCK.
6. EXTEND BOLT
TURN THE DIAL TO THE LEFT (CCW) TO EXTEND THE BOLT. DO NOT CLOSE THE DOOR
7. POWER LOCK - EC
TURN THE DIAL TO THE LEFT (CCW) UNTIL EC (THE CHANGE KEY SYMBOL ALONG WITH ENTER COMBINATION) IS DISPLAYED.
8. EC - PRESS #8 - ECF
PRESS THE “#” BUTTON FOLLOWED BY THE “8” BUTTON. ECF (ENTER COMBINATION,FACTORY) WILL BE DISPLAYED.
9. E
CF - ENTER CURRENT SHELVED MODE COMBINATION - ENF
ENTER THE CURRENT SHELVED MODE COMBINATION, “ENF” (ENTER NEW FACTORY COMBINATION) WILL BE DISPLAYED

12
COMMON ERROR CODES
33
FEED FAILURE
1. REMOVE AND OPEN CASSETTE(S). IF THERE IS CURRENCY IN CASSETTE, GO
TO STEP 2. IF NOT, LOAD CURRENCY AND PROCEED TO STEP 3.
2. IS CURRENCY OF GOOD QUALITY? IF YES, GO TO STEP 4. IF NOT, OBTAIN
QUALITY CURRENCY. PROCEED TO STEP 4.
3. SHUFFLE CURRENCY AND REPACK CASSETTE.
4. RE-INSERT CASSETTE USING REPLENISHING CASSETTE PROCEDURES.
5. PERFORM A TEST DISPENSE (DIAGNOSTICS>DISPENSER>TEST DISPENSE).
IF SUCCESSFUL, PLACE ATM IN SERVICE.
101
306
139
140
141
PRINTER CONTROL-
LER NOT RESPONDING
PAPER JAM REPORTED
TIME-OUT WAITING
FOR PRINTER TO BE
READY
2. PULL THE PRINTER RELEASE PIN. OPEN THE PRINTER/CUTTER ASSEMBLY
AND VERIFY THERE ARE NO JAMS IN THE PRINTER OR THE PAPER PATH. VERIFY
THE BLUE LEVER ON THE LEFT SIDE OF THE PRINTER IS IN THE CORRECT
POSITION. CLOSE THE PRINTER/CUTTER ASSEMBLY.
3. PERFORM A RESET/TEST PRINTER (DIAGNOSTICS>PRINTER>RESET/
TEST PRINTER) COMMAND. IF SUCCESSFUL, PLACE ATM IN SERVICE.
1. VERIFY THAT THERE IS PAPER IN THE PRINTER. REPLENISH PAPER AS
NEEDED.
ERROR
CODE MEANING RECOMMENDATIONS
156 CASSETTE OUT OF
SERVICE
194 CASSETTES NOT
LOCKED
1. THIS OCCURS WHEN THE LAST AVAILABLE CASSETTE DISPENSING
CURRENCYHAS BEEN TAKEN OUT OF SERVICE. CASSETTES ARE TAKEN OUT OF
SERVICE BECAUSE OF FEED FAILURES OR EXCESSIVE REJECTS.
2. INSPECT CASSETTES. FILL IF NEEDED. IF THEY ARE NOT EMPTY, SEE RECOM-
MENDED ACTION FOR “FEED FAILURE” (ABOVE).
3. PLACE CASSETTES “IN-SERVICE” FROM MANAGEMENT FUNCTIONS MENU.
IF WORKING WITH AN NMD-50 DISPENSER, LOCK THE CASSETTES FROM
MANAGEMENT FUNCTIONS MENU.
185
to
190
TERMINAL
CONFIGURATION
ERRORS
ENTER MANAGEMENT FUNCTIONS AND CHECK/CONFIGURE:
- TELEPHONE NUMBER (EC 185), CURRENCY VALUES (EC 186), MAXIMUM
WITHDRAWAL AMOUNT (EC 187), PIN WORKING KEYS (EC 188), TERMI-
NAL ID (EC 189), PIN MASTER KEY (EC 190).