Triton RT2000 User manual

TDN 07100-00098B
THISAREAFORSERVICEPROVIDER
CONTACT INFORMATION:
06/2008
Model RT2000 (X2)
QUICK REFERENCE GUIDE

2
MANAGEMENT FUNCTIONS
- ACCESS INSTRUCTIONS -
1. ATATM WELCOME SCREEN, PRESS AND HOLD DOWN THE <CTRL>
KEY (LOWER-RIGHT CORNER OF KEYPAD), PRESS <1> KEY, THEN RE-
LEASE BOTH KEYS. THE PASSWORD ACCESS PROMPT IS DISPLAYED.
2. ENTER PASSWORD AND SELECT <ENTER>. THE MANAGEMENT FUNCTIONS MAIN MENU IS DISPLAYED.
TERMINALCONFIGURATION REPORT
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT DIAGNOSTICS > TERMINAL STATUS.
CONFIGURATION SUMMARY: THIS SUMMARY IS ACOMPREHENSIVE
REPORT OF CURRENT TERMINAL CONFIGURATION AND HARDWARE STATUS IN-
FORMATION.
NOTE: ITIS HIGHLY RECOMMENDED THAT THIS REPORT BE PRINTED AND SAVED AFTER INITIAL SETUP AND WHENEVER
CHANGES ARE MADE TO THE TERMINALS CONFIGURATION.
RESTART/ SHUTDOWN TERMINAL
RESTARTTERMINAL: THIS FUNCTION REBOOTS THE TERMINAL.
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT SYSTEMPARAMETERS.
SHUTDOWN TERMINAL: THIS FUNCTION POWERS-DOWN THE TERMI-
NALS OPERATING SYSTEM. WHEN PROMPTED THAT SHUTDOWN IS COMPLETE,
TURN ON/OFF SWITCH ON POWER SUPPLY TO <OFF> POSITION.

3
DIAGNOSTICS
PURGE: THIS INSTRUCTS THE DISPENSER TO REMOVE ANY NOTES (JAMS) IN
FEED PATH.
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT DIAGNOSTICS > DISPENSER.
TEST DISPENSE: THIS INSTRUCTS THE DISPENSER TO DISPENSE MINIMUM
ONE NOTE FROM EACH INSTALLED CASSETTE INTO THE REJECT CASSETTE/
AREA.
RESET / TEST PRINTER: THIS
INSTRUCTS THE PRINTER TO RE-INI-
TIALIZE AND PERFORM ATEST PRINT-
OUT.
SELECT DIAGNOSTICS > PRINTER.
PRINT LAST X: TOVIEW/PRINT PREVIOUSLY AUDITED OR UNAUDITED
RECORDS, USE THE PRINT LAST X OPTION.
JOURNAL FUNCTIONS
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT JOURNAL.
EXAMPLE: ENTERING THE NUMBER ‘50’ WILL LET YOU VIEW THE LAST 50 TRANSACTIONS/EVENTS THAT HAVE OC-
CURRED. YOU MAY PRINT TO THE RECEIPT PRINTER.
DAYCLOSE: THIS OPTION IS USED TO COMPLETE DAILY BALANCING OF THE
ATM WITH THE PROCESSOR. TOTALS ARE CLEARED AND SWITCHED TO THE
NEXT BUSINESS DAY.
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT TERMINALCLOSE FUNCTIONS.
TRIALCLOSE: THIS OPTION FUNCTIONS LIKE ADAY CLOSE EXCEPT THE TOTALS ARE NOT CLEARED.
CLOSEFUNCTIONS

4
CASSETTECLOSEFUNCTIONS
(FROM THE FRONT DISPLAY)
FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SELECT TERMINALCLOSE FUNCTIONS.
SELECT CASSETTE CLOSE.
SELECT CASSETTE(S) TO CLOSE. ACHECK MARK ( √√
√√
√)
IDENTIFIES WHICH CASSETTE(S) ARE SELECTED. PRESS <EN-
TER>.
AFTER CASSETTE(S) HAVE BEEN REINSERTED IN THE DIS-
PENSER, PRESS <ENTER>.
A CLOSE REPORT IS DISPLAYED TO BE PRINTED OR SAVED.
THIS OPERATION WILL RESET THE NUMBER OF BILLS IN THE
CASSETTE(S) TO ZERO (0). PRESS <ENTER>.
REMOVE AND REPLENISH THE SELECTED CASSETTE(S).
FOLLOW CASSETTE REPLENISHMENT PROCEDURES.
PLACE SELECTED CASSETTE(S) IN SERVICE. PRESS
<ENTER>. NOTE: FOR TDM-200/250 DISPENSERS.
ENTER CASSETTE QUANTITY (NUMBER OF NOTES, NOT
VALUE) FOR THE SELECTED CASSETTE(S). PRESS <ENTER> TO
ACCEPT ENTRY. REPEAT FOR EACH SELECTED CASSETTE.
A TRIAL CASSETTE CLOSE REPORT AUTOMATICALLY IS
DISPLAYED TO BE PRINTED OR SAVED. PRINT AND RETAIN A
COPY FOR STARTING POINT REFERENCE. PRESS <ENTER> TO
RETURN TO CLOSE FUNCTIONS.
**IMPORTANT**
ENSURE THE MULTIPLEAMOUNTPARAMETER MATCHES
THE DENOMINATION OF CURRENCY IN EACH NOTE CASSETTE!

5
CASSETTECLOSEFUNCTIONS
(FROM THE REAR OPERATOR SERVICE PANEL (TOUCHSCREEN)



PRESS TO START.


ENTER PASSWORD.
SELECT “CASSETTE CLOSE”.
CLOSE CASSETTE(S) - TOUCH CAS-
SETTE OPTIONS ON TOUCHPAD UNTIL
“ASTERICK” APPEARS. SELECT “CON-
TINUE”.

CASSETTE CLOSE REPORT APPEARS.
PRINT REPORT. PRESS “EXIT” WHEN
COMPLETED.
*** Cassette Close ***
Cassette A
Last Close Date/Time:
6/4/2007 7:49:39 AM
Start Quantity:
Qty: 200
Amount: $2000.00
Dispensed:
Qty: 50
Amount: $500.00
Remaining:
Qty: 150
Amount: $1500.00

REMOVE /REPLENISH CASSETTE(S).
PRESS “ENTER”.
PLACE CASSETTES “IN-SERVICE”.
TOUCH CASSETTE OPTIONS ON
TOUCHPAD UNTIL “ASTERICK” AP-
PEARS. SELECT “CONTINUE”.

TRIAL CASSETTE CLOSE REPORT
APPEARS. PRINT REPORT. PRESS
“EXIT” WHEN COMPLETED.

ENTER CASSETTE QTY (EACH).
PRESS “OK”.
SELECT “TERMINAL CLOSE FUNCTIONS”.
Select the cassettes to close.
WARNING: Cassette totals will be
reset for the selected cassettes
* Cassette A: $10.00
* Cassette B: $20.00
Continue Exit
Select the cassettes to place in
service.
* Cassette A: $10.00
* Cassette B: $20.00
Continue Exit
Cassette Quantity - Cassette A:
Please enter the number of bills that
are in the cassette (not the value).
123
456
789
0
<>
CANCEL
CHANGE
OK
200
You may now remove and replenish
the cassettes. Press ENTER when
done.
Enter
*** Trial Cassette Close ***
Cassette A
Last Close Date/Time:
6/4/2007 7:55:39 AM
Start Quantity:
Qty: 200
Amount: $2000.00
Dispensed:
Qty: 0
Amount: $00.00
Remaining:
Qty: 200
Amount: $2000.00

6
REPLENISHCASSETTE(S)
UNLOCK / OPEN
VAULT CABINET
DOOR. THE DIS-
PENSER IS MOUNTED
TO ASLIDING TRAY.
NOTE: THE TRAY
DOESNOTNEED TO
BE EXTENDED FOR
CURRENCY REPLEN-
ISHMENT.
1
6
4
5
REMOVE REJECT CASSETTE BY GRASPING THE
BOX AND PULLING FROM THE DISPENSER.
3
2
NOTE: CURRENCY REPLENISHMENT FOR ACASSETTE IS THE SAME
FOR EITHER CASSETTE.
COUNT THE NUMBER OF BILLS THAT REMAIN IN
THE CASSETTE,IF ANY.
COUNT THE NUMBER OF BILLS THAT ARE BEING
ADDED TO THE REMAINING NOTES.
THE TOTAL OF THESE AMOUNTS WILL BE EN-
TERED IN THE “ENTER CASSETTE QUANTITY”
PROMPT FOR CASSETTE CLOSE PROCEDURE.
PLACE CURRENCY IN THE CASSETTE AND
SLOWLY RELEASE THE LATCH ALLOWING THE
PACKER PLATE TO MOVE FORWARD AGAINST THE
NOTES.
UNLOCK NOTE CAS-
SETTE WITH SUPPLIED
KEY. OPEN LID. MOVE
PUSHER PLATE TO-
WARDS REAR OF CAS-
SETTE AND SECURE IN
PLACE WITH KEY
LATCH MECHANISM.
STEP ACTION
STEP ACTION
CLOSE LID,LOCK CAS-
SETTE AND REINSERT
BACK INTO THE DIS-
PENSER. ENSURE CAS-
SETTE IS FULLY IN-
SERTED.
REMOVE THE NOTE
CASSETTE(S) BY
GRASPING THE
GREEN HANDLE AND
PULL FROM THE DIS-
PENSER.
PLACE CASSETTE(S) ON AFLAT SURFACE.
CLOSE, LOCK, AND REINSERT THE REJECT CAS-
SETTE BACK INTO THE DISPENSER.
DONOTRECYCLE REJECTED NOTES!
UNLOCK AND REMOVE ANY REJECTED NOTES.

7
14
25
36
STEP ACTION
REPLENISHRECEIPTPAPER
STEP ACTION
PULL RELEASE PIN,
GRASP HANDLE, AND
ROTATE PRINTER AS-
SEMBLY UP TO THE
SERVICE POSITION.
INSTALL NEW PAPER
ROLL/ SPINDLE IN
BRACKET.
PAPER FEEDS FROM
BOTTOMOF ROLL!
FEED END OF PAPER
OVER BAR AND INTO
PRINTER TAKE-UP
SLOT. PRINTER WILL
AUTOMATICALLY
GRIP AND PULL PAPER
INTO FEED PATH.
NOTE: THIS PROCEDURE REQUIRES TERMINAL IS POWERED UP.
OPEN THE REAR
CABINET SLEEVE
DOOR. IFPAPER RE-
MAINS ON ROLL, CUT
OR TEAR PAPER BE-
TWEEN ROLL AND
PRINTER.
RELEASE (OPEN)THE BLUE TENSION LEVER SHOWN.
REMOVE ANY PAPER FROM THE PRINTER/CUTTER
ASSEMBLY.
MOVE THE TEN-
SION LEVER BACK
TO THE CLOSED
POSITION. ROTATE
DOWN THE
PRINTER ASSEM-
BLY.
NOTE: THIS POSITION
ALSO ALLOWS RECEIPT
ACCESS FOR PRINTING
REPORTS IF USING THE
REAR SERVICE PANEL
REMOVE SPENT PA-
PER ROLL AND
SPINDLE FROM PAPER
BRACKET.
Closed
Open
RECOMMEND PERFORM ADIAGNOSTIC TEST OF
THE PRINTER. GOTO MAIN MENU > DIAG-
NOSTICS > PRINTER > RESET/TEST
PRINTER. THIS FUNCTION RE-INITIALIZES
AND PERFORMS AN OPERATIONAL TEST OF THE
PRINTER.

8
COMBINATION LOCKS
INTRODUCTION
THE SECURITY CABINET CAN BE SECURED USING EITHER AMECHANICAL OR ELECTRONIC COMBINATION LOCK.THIS PAGE COVERS HOW
TO OPERATE THE COMBINATION OF EITHER LOCK.
OPERATING THE MECHANICAL LOCK
UNLOCKING THE LOCK
THERE ARE TWO MARKS ON THE DIAL RING. THE INDEX AT THE TOP IS USED FOR OPENING THE LOCK,THE INDEX 30 DEGREES TO THE LEFT
IS USED ONLY WHEN CHANGING THE COMBINATION.
THE DIAL SHOULD ALWAYS BE TURNED SLOWLY AND EVENLY. AREVOLUTION IS COUNTED EACH TIME THE SELECTED NUMBER IS ALIGNED
WITH THE OPENING INDEX. DONOT TURN THE DIAL BACK TO COMPENSATE FOR OVER-DIALING ANUMBER.IF, WHEN DIALING THE
COMBINATION,ANY NUMBER IS TURNED BEYOND THE INDEX, THE ENTIRE SEQUENCE MUST BE REPEATED.
UNLOCKING 3-NUMBER COMBINATIONS (FOR EXAMPLE, “50-25-50”)
1. TURN THE DIAL TO THE LEFT AT LEAST FOUR (4)COMPLETE TURNS TO CLEAR THE COMBINATION LOCK TO ACCEPT THE
COMBINATION.
2. USING THE ‘OPENING INDEX’,TURN THE DIAL TO THE LEFT,STOPPING WHEN ‘50’IS ALIGNED WITH THE OPENING INDEX, THE
FOURTH TIME.
3. TURN THE DIAL TO THE RIGHT,STOPPING WHEN ‘25’IS ALIGNED WITH THE OPENING INDEX, THE THIRD TIME.
4. TURN THE DIAL TO THE LEFT, STOPPING WHEN ‘50’IS ALIGNED WITH THE OPENING INDEX, THE SECOND TIME.
5. TURN THE DIAL SLOWLY TO THE RIGHT UNTIL THE BOLT RETRACTS.
OPERATING THE ELECTRONIC LOCK
THE ELECTRONIC LOCK COMBINATION CONSISTS OF SIX DIGITS. UPON ARRIVAL, THE COMBINATION OF THE LOCK SHOULD ALREADY BE
PRESET TO 1-2-3-4-5-6. NOTE:CHANGE THIS COMBINATION! SEE USER MANUAL FOR CHANGING COMBINATION PROCEDURES.
ENTERING THE COMBINATION
1. ENTER THE CURRENT COMBINATION AND CHECK FOR PROPER OPERATION. AFTER EACH KEYPRESS,THE LOCK WILL BEEP. AFTER THE
FINAL DIGIT HAS BEEN ENTERED, THE LOCK WILL BEEP TWICE, AND THE OPEN PERIOD WILL BEGIN.
2. WHEN AVALID COMBINATION HAS BEEN ENTERED,THE OPERATOR WILL HAVE APPROXIMATELY 4SECONDS TO OPEN THE LOCK.
3. TOOPEN THE LOCK,TURN THE OUTER DIAL CLOCKWISE.
4. AFTER THE LOCK IS OPENED,THE CABINET DOOR MAY BE OPENED.
LOCKOUT FEATURE
THE LOCK INCLUDES A‘WRONG TRY PENALTY’LOCKOUT FEATURE THAT PREVENTS ENTRY FROM UNAUTHORIZED PERSONNEL. THIS
FEATURE PERFORMS AS FOLLOWS:
•ENTRY OF FOUR (4)CONSECUTIVE INVALID COMBINATIONS STARTS A5-MINUTE DELAY PERIOD.
- LEDFLASHES RED AT TEN (10)SECOND INTERVALS.
•ATTHE END OF THE DELAY PERIOD,TWO (2)MORE CONSECUTIVE INVALID COMBINATIONS WILL RESTART AN ADDITIONAL 5-MINUTE
DELAY.