Tyco Electronics 408-10254 User manual

Instruction heet
PARALIGHT*
Active Optical 408-10254
LOC B
1 of 2
E 2008 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
TOOLING A I TANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change. For latest revision and Regional Customer ervice,
visit our website at www.tycoelectronics.com
22 DEC 08 Rev A
Ca le Assem lies
1. INTRODUCTION
This product is for use in a restricted access
location onl .
This instruction sheet provides installation guidelines
for Tyco Electronics Active Cables for both CX4 D and
QSFP connectors. Proper handling procedures
should be exercised when transporting or installing
the cables. Operation of the product must be
maintained within the 0 to 60°C operating ambient
temperature range.
D CX4 connector is also known as Infiniband 4X or
SFF–8470.
This product does not contain an adjustable
controls.
Use of controls or adjustments or performance of
procedures other than those specified herein ma
result in hazardous radiation exposure.
Product is to be installed in accordance with both
National and Local regulations and/or
requirements or other authorit having
jurisdiction.
2. INSTALLATION GUIDELINES FOR CX4 STYLE
CONNECTOR ENDS
Refer to Figure 1 for installation of CX4 style
connectors.
1. Correctly align the CX4 plug with the receptacle
as shown in Figure 1A.
2. Insert the plug into the receptacle until it
bottoms. See Figure 1B.
3. To remove the plug from the receptacle, pull on
the “release handle” in the indicated direction until
the connector is removed as shown in Figure 1C.
3. INSTALLATION GUIDELINES FOR QSFP STYLE
CONNECTOR ENDS
Refer to Figure 2 for installation of QSFP style
connectors.
1. Correctly align the QSFP plug with the
receptacle as shown in Figure 2A.
Figure 1
1A 1B
1C
Align CX4 Plug
with Receptacle
Insert Plug into Receptacle
Until It Bottoms
Pull on Release
Handle" to Remove
(Do NOT Pull on
Cable)
IEC60825-1
NOTE
i
NOTE
i
DANGER
NOTE
i

408-10254
PARALIGHT Act ve Opt cal Cable Assembl es
Rev A2 f2 Tyc Electr nics C rp rati n
Figure 2
2A 2B
2C
Align QSFP Plug
with Receptacle
Insert Plug int
Receptacle
Until It B tt ms
Pull n Pull
Tab" t Rem ve
(D NOT Pull
n Cable)
2. Insert the plug into the receptacle until it
bottoms. See Figure 2B.
3. To remove the plug from the receptacle, pull
back on the “pull tab” in the indicated direction until
it is removed as shown in Figure 2C.
4. HANDLING
Maximum bend radius of the optical cable per
ICEA–596 in the unloaded and install condition is
29 mm and in the loaded condition during installation
is 58 mm.
This product is classified as a Class 1M Laser product
in accordance with IEC 60825–1:1993+A1+A2 and
complies with 21CFR 1040.10 and 1040.11 except for
deviations pursuant to laser notice No. 50, dated
24–Jun–2007.
Do not c t or view a damaged fiber optic cable
with the naked eye or magnification instr ment.
For se with UL Listed ITE comp ting or
telecomm nication devises having SELV I/O
connections only.
5. REVISION SUMMARY
S Initial release of document
DANGER
NOTE
i