U-Line H-9975 User manual

PAGE 1 OF 5 0222 IH-9975
H-9975, H-9976
TELESCOPIC POLE KIT
AND OPTIONAL HYDROPOWER
TANK AND BRUSH ASSEMBLY
1-800-295-5510
uline.com
PARTS
ASSEMBLY
1
2
34
PARTS
#DESCRIPTION QT Y.
16-Section Main Pole 1
22-Section Extension Pole 2
3Tool Adapter 1
4Gooseneck Attachment 1
NOTE: Do not fully extend the main telescopic
pole laying flat on the ground. Always extend
pole vertically into the air.
NOTE: Always start with main pole. If a longer
length is required once main pole is fully
extended, add each extension pole at the
bottom, extending main pole further up into
the air.
1. To extend telescopic pole, flip open each locking
clip and pull out the nested extension. Close locking
clip. (See Figures 1-2)
Figure 1 Locking
Clip
Figure 2

PAGE 2 OF 5 0222 IH-9975
2. Main pole must be extended first before an
extension pole can be added. To add an extension
pole, insert top of the extension pole into bottom of
the main pole.
NOTE: Extension pole is fully inserted when the
yellow locking pins click into place.
(See Figures 3-4)
Figure 3
Extension Pole
Main Pole
Locking Pin
Figure 4
NOTE: To attach dusting or squeegee tools to
telescopic pole, gooseneck attachment and
tool adapter must first be attached to the top
of main pole.
3. To attach gooseneck, flip open the locking clip at
the top of main pole, and loosen the connection as
needed by adjusting screw. Insert the gooseneck
into the pole. Close the locking clip and tighten
screw. (See Figures 5-6)
Figure 5
Figure 6
NOTE: Gooseneck can be bent 180 degrees.
To adjust the angle, flip open locking clip,
bend gooseneck to desired position and close
locking clip. (See Figure 7)
Figure 7
4. Press tool adapter onto gooseneck. It will click into
place. (See Figures 8-9)
Figure 8
Figure 9
NOTE: To convert this telescopic pole into a
water-fed pole for window cleaning, attach
optional Hydropower Tank and Brush (Uline
model # H-9976) assembly. See pages 3-5.
ASSEMBLY CONTINUED
Locking
Clip
Screw
Locking
Clip
Tool Adapter
Gooseneck

PAGE 3 OF 5 0222 IH-9975
1. Route hose internally through main pole.
2. Remove gooseneck. Feed hose through base of the
main pole up and through the top.
(See Figures 10-11)
Figure 10
F i g u re 11
3. Thread hose through the hole in gooseneck.
(See Figure 12)
Figure 12
4. Re-attach gooseneck. (See Figure 13)
Figure 13
OPTIONAL HYDROPOWER TANK AND BRUSH ASSEMBLY PARTS
PARTS
#DESCRIPTION QT Y.
1 Ultra-Pure Resin Filter Tank 1
2Power Brush 1
3Extension Adapter 1
482' Hose 1
ASSEMBLY
1
3
2
4
Hose
Gooseneck
Main
Pole
Hose
Hose
Gooseneck

PAGE 4 OF 5 0222 IH-9975
ATTACHING BRUSH
1. Remove elbow fitting from the clear hose in the
brush neck. (See Figure 14)
Figure 14
2. Route clear hose through the gooseneck and out
the side opening (remove the yellow cap to expose
the opening). Attach brush to the gooseneck by
clicking it into place. (See Figures 15-16)
NOTE: This brush has two clear hoses. Either can
be connected to the main hose, depending on
where the water flow is desired.
Figure 15
Opening
Gooseneck
Yellow Cap
Figure 16
Clear Hose
Opening
Clear Hose
3. Connect brush hose and main hose with the elbow
fitting. (See Figure 17)
Elbow
Fitting
Brush Hose
Main Hose
F i g u re 17
4. Attach the other end of the main hose to the
ultra-pure resin filter tank. (See Figure 18)
NOTE: The hose connects at the top of the tank,
by connecting the quick-connect fitting. The
fitting at the base of the tank connects to a
garden hose.
Main Hose
Ultra-Pure
Resin Filter Tank
Quick-Connect
Fitting
Figure 18
5. If extension poles are needed while using the pole
with ultra-pure resin filter tank and brush assembly,
the extension adapter must be used. This allows
an extension pole to connect to main pole without
disrupting the hose. The hose will remain internally
routed through main pole but will hang externally
from the extension adapter for the length of
extension pole.
NOTE: Extension adapter is grooved to allow
space for hose. Ensure hose is placed in the
groove when inserting the extension adapter.
ASSEMBLY CONTINUED
Elbow
Fitting

PAGE 5 OF 5 0222 IH-9975
ASSEMBLY CONTINUED
6. To insert extension adapter into main pole, align the
arrows and push into place until locking pins click
into place. (See Figures 19-21)
Figure 19
Extension Adapter
Locking Pin
Main Pole
NOTE: Figure 22 shows unit properly assembled.
Figure 20 Figure 21
1
-800-295-551
0
uline.com
Arrows
Extension Adapter
in Use
Extension
Pole
Main
Pole
Hose
Figure 22