URBAN OUTFITTERS CASTELLA User manual

CASTELLA MIRROR
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 1 of 3
TOOLS REQUIRED BUT NOT INCLUDED:
Do not throw away packing materials and carton until after assembly.
Assemble all parts on a clean smooth surface
CARE INSTRUCTIONS:
Avoid direct exposure to sunlight. Do not place over heat or Air conditioning
vents.Adjust levelers so that the furniture sits flat on uneven floors.
Blot spills do not rub, with a clean white
cloth.Do not use harsh chemicals.
Before cleaning any part test a small spot in a hidden
area.You may need to re-tighten all bolts after initial
use.
PARTS INCLUDED
C D E F G H
4 X 4 X 4 X 2X 3x32mm 2X 3x19mm 2X
CASTELLA MIRROR
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 1 of 3
TOOLS REQUIRED BUT NOT INCLUDED:
Do not throw away packing materials and carton until after assembly.
Assemble all parts on a clean smooth surface
CARE INSTRUCTIONS:
Avoid direct exposure to sunlight. Do not place over heat or Air conditioning
vents.Adjust levelers so that the furniture sits flat on uneven floors.
Blot spills do not rub, with a clean white
cloth.Do not use harsh chemicals.
Before cleaning any part test a small spot in a hidden
area.You may need to re-tighten all bolts after initial
use.
PARTS INCLUDED
C D E F G H
4 X 4 X 4 X 2X 3x32mm 2X 3x19mm 2X
CASTELLA MIRROR
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 1 of 3
TOOLS REQUIRED BUT NOT INCLUDED:
Do not throw away packing materials and carton until after assembly.
Assemble all parts on a clean smooth surface
CARE INSTRUCTIONS:
Avoid direct exposure to sunlight. Do not place over heat or Air conditioning
vents.Adjust levelers so that the furniture sits flat on uneven floors.
Blot spills do not rub, with a clean white
cloth.Do not use harsh chemicals.
Before cleaning any part test a small spot in a hidden
area.You may need to re-tighten all bolts after initial
use.
PARTS INCLUDED
C D E F G H
4 X 4 X 4 X 2X 3x32mm 2X 3x19mm 2X

CASTELLA MIRROR
Assembly Instructi
ons
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable c
opyright, design and patent
rights. Any unauthorized reproduction,adaptation, distribution
or other infringement will be
prosecuted.
Page 2 of 3
STEP 1
Align wooden french cleat (B) to wall.
Mark the top of the Mirror with a pencil. Measure the center of the mirror.
The distance to the hole location is 56”
or 1420 mm from the floor. Measure and mark these 4 spots. It is best to
use a level to make sure the mirror hangs
square.
Insert anchors (C) and screw them into th
e wall flush. Screw in the screws (D) with a Phillips head screw- driver
(not included).
STEP 2
With help hang the mirror onto wooden f
rench cleat (B).
CASTELLA MIRROR
Assembly Instruction
s
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable cop
yright, design and patent
rights. Any unauthorized reproduction,adaptation, distribution o
r other infringement will be
prosecuted.
Page 2 of 3
STEP 1
Align wooden french cleat (B) to wall. Mar
k the top of the mirror with a pencil. Measure
the center of the mirror.
The distance to the holes location is 56” or
1420 mm from the floor. Measure and mark th
ese 4 spots. It is best to
use a level to make sure the mirror hangs s
quare.
Insert anchors (C) and screw them into the
wall flush. Screw in the screws (D) with a Ph
illips head screw- driver
(not included).
STEP 2
With help hang the mirror onto wooden fre
nch cleat (B).
CASTELLA MIRROR
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction,adaptation, distribution or other infringement will be
prosecuted.
Page 2 of 3
STEP 1
Align wooden french cleat (B) to wall. Mark the top of the Mirror with a pencil. Measure t
he center of the mirror.
The distance to the holes location is 56” or 1420 mm from the floor. Measure and mark the
se 4 spots. It is best to
use a level to make sure the mirror hangs square.
Insert anchors (C) and screw them into the wall flush. Screw in the screws (D) with a Philli
ps head screw- driver
(not included).
STEP 2
With help hang the mirror onto wooden french cleat (B).

CASTELLA MIRROR
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 3 of 3
STEP 3
To prevent injury and property damage from unexpected tipping of furniture.
1. Attached the mounting bracket horizontally to the top back edge of the furniture. Insert the short
screws through the holes in the bracket and tighten securely using screwdriver. Please contact your
local hardware store to get the correct anchor for your wall type.
2. Determine where the furniture is to be placed and mark location on the wall for the other mounting
bracket crew holes. It should be placed approximately 2” below the bracket mounted to the furniture.
3. Attached the mounting bracket vertically to the wall by inserting the long screws provided through the
hole in the bracket and tightening securely using screwdriver. Please contact your local hardware store
to get the correct anchor for your wall type.
4. Place the furniture so the bracket on the back edge are in line with the brackets on the wall.
5. Lace an end of the nylon restraint strap down through each bracket. Bring both ends together and slide
the thin end of the strap through the receiving end of the strap until snug.
6. Check to make sure the strap is securely laced and locked to the bracket.
CASTELLA MIRROR
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 3 of 3
STEP 3
To prevent injury and property damage from unexpected tipping of furniture.
1. Attached the mounting bracket horizontally to the top back edge of the furniture. Insert the short
screws through the holes in the bracket and tighten securely using screwdriver. Please contact your
local hardware store to get the correct anchor for your wall type.
2. Determine where the furniture is to be placed and mark location on the wall for the other mounting
bracket crew holes. It should be placed approximately 2” below the bracket mounted to the furniture.
3. Attached the mounting bracket vertically to the wall by inserting the long screws provided through the
hole in the bracket and tightening securely using screwdriver. Please contact your local hardware store
to get the correct anchor for your wall type.
4. Place the furniture so the bracket on the back edge are in line with the brackets on the wall.
5. Lace an end of the nylon restraint strap down through each bracket. Bring both ends together and slide
the thin end of the strap through the receiving end of the strap until snug.
6. Check to make sure the strap is securely laced and locked to the bracket.
CASTELLA MIRROR
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 3 of 3
STEP 3
To prevent injury and property damage from unexpected tipping of furniture.
1. Attached the mounting bracket horizontally to the top back edge of the furniture. Insert the short
screws through the holes in the bracket and tighten securely using screwdriver. Please contact your
local hardware store to get the correct anchor for your wall type.
2. Determine where the furniture is to be placed and mark location on the wall for the other mounting
bracket crew holes. It should be placed approximately 2” below the bracket mounted to the furniture.
3. Attached the mounting bracket vertically to the wall by inserting the long screws provided through the
hole in the bracket and tightening securely using screwdriver. Please contact your local hardware store
to get the correct anchor for your wall type.
4. Place the furniture so the bracket on the back edge are in line with the brackets on the wall.
5. Lace an end of the nylon restraint strap down through each bracket. Bring both ends together and slide
the thin end of the strap through the receiving end of the strap until snug.
6. Check to make sure the strap is securely laced and locked to the bracket.