VEVOR DT-S005 User manual

Technical Support and E-Warranty Certificate www.vevor.com/support
ELECTRIC WAX MELTER
DT-S005(A), DT-S005(B), DT-S005(C)
USER MANUAL
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the
major top brands and doses not necessarily mean to cover all categories of tools offered by
us. You are kindly reminded to verify carefully when you are placing an order with us if you
are actually saving half in comparison with the top major brands.

1
Have product questions? Need technical support? Please feel free to
contact us:
CustomerSe[email protected]
NEED HELP? CONTACT US!
This is the original instruction, please read all manual instructions
carefully before operating. VEVOR reserves a clear interpretation of our
user manual. The appearance of the product shall be subject to the
product you received. Please forgive us that we won't inform you again if
there are any technology or software updates on our product.
Electric Wax Melter

2
INTRODUCTION
Electric wax melter are manufactured in durable stainless steel and
dull polished to give a long lasting finish. With proper care and
management your new purchase will give you years of trouble free
service .
IMPORTANT SAFETY RULES
1. Read all instructions carefully.
Responsibility for failure cannotbe accepted if any of these
instructions are ignored.
2. Always unplug the melter plug before cleaning, after use,
and after emptying.
3. Before using the Wax melter, check whether the voltage
indicatedcorresponds with the electric outlet (EU Plug
230V/US Plug 120V).
4. Make sure the unit is connected to an earthed socket.
5. Do not use the Wax melter if the cord or plug is damaged, it
shouldbe replaced before using.
6. Always switch off before removing plug from the outlet.
7. Always switch off before trying to move the wax melter.
8. Remove the plug by grasping the plug. Do NOT pull the cord.
9. Do not let cord hang over edge of counter.
Place the wax melter securely in center of counter or work
space. Never place on a tilted surface.
10.Do not place the wax melter on or near hot surfaces.
11.Do not switch on the Wax melter, if the wax tank is empty.
12.Do not place the wax melter near gas stove, electric
burner orheated oven.
13.Put the Wax melter on flat stable surface; keep it away
from theedge of counter to avoid accident.
14.Close supervision is necessary when any appliance is used
by ornear children.
15.Do not allow cord to touch hot surface of the Wax melter.
16.To protect against electric shock, DO NOT IMMERSE IN
WATER for the Wax melter.
17.Unplug the unit from the socket, and pour out all the wax

3
before itcools .
18.Switch OFF after use and unplug the unit from the socket.
19.Do not use the Wax melter outdoor. INDOOR USE ONLY
20.Do not overfill the Wax melter with wax, doing so can
lead tospillage as the wax heats up and expands.
21.Improper use of the Wax melrer may result in severe scalding.
22.Beware of hot steam when removing the lid.
23.Always ensure the lid is securely fitted whenever the wax
meltercontains wax.
24.Do not turn on or attempt to operate the wax melter when
the waxlevel is at or below the Min level.
25.Do not turn on the wax melter when the wax level is above
the Maxlevel. When the wax boils it will cause spillage.
26.If the wax melter should boil dry there is an overheat cut out
whichcan automatically reset. However repeated
overheating will eventually damage the heating element.
27.If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
28.Do not attempt to disassemble the wax melter. This will
void yourwarranty.
29.To avoid a plugged faucet, the remaining wax can not be
higher than the faucet when the power is cooling.
30.This machine is not suitable for jelly wax.
31.This machine should not be operated by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience or knowledge,
unless they have been given supervision or instruction
concerning the safe use of theappliance by a person
responsible for their safety.
SAVE THESE INSTRUCTIONS

4
PRIOR TO FIRST USE:
Remove all packaging from the inside and outside of the wax melter
HOW TO USE
1. Always use the wax melter on a flat level surface.
2. Turn the lid anti clockwise to open.
3. Fill the wax melter not above the Max level indicator.
4. Replace the lid and turn clockwise to lock into place.
5. Connect the plug to the socket.
6. Switch ON. The Red "Heating" pilot lamp will light up and
the waxstarts to heat up.
7. The wax will reach the set thermostat temperature.
8. Stand your cup on the hold close to the faucet to prevent
splashingof wax.
9. Use the faucet to dispense wax.
10.When the wax is topped up the wax melter will automatically
reboil.
11.When the wax is completely melted, turn the appliance off,
unplug it from the electric outlet, and pour out all the wax.
12.Make sure at least 500ml wax in the tank when heating to

5
preventa boil-dry accident.
13.The melter can be very heavy when filled with wax. Melter
should not be carried or moved when full of wax as the
weight and unsteady load can cause injury or strain. Melter
should be placed in their position of use and filled through
several trips with a smaller,manageable container (eg a jug).
To ensure operator safety in lifting the machines, Melter
should never be moved when filled with more than 5L (5L
=5Kg approximately).
BOIL DRY PROTECTION
The appliance is protected by a thermal limiter with
automatically re- set function to prevent accidental dry-boil. .If
the wax in the tank is boiled dry , this is activated, the appliance
will turn itself off, although the lamp with remain on. The
appliance must be unplugged before it can be reset. To
reset the appliance, wait until the appliance has cooled down,
then power on the appliance again, check if the heating pilot
light is on. If the pilot light is on, it indicates the unit has
recoveredto normal working condition; if the light is still off,
unplug the cord and try to power on again. Repeat this
operation several times until the appliance is under normal
working condition.
This facility is for the protection of the user as well as the
components.In case of such repeated incidents the bi-metal
may malfunction causing damage of thermal limiter as well as
the heating element beyond repair. Please note that the
manufacturer will not guarantee forsuch negligent use of
appliance.
If resetting this thermal cut-out does not switch the appliance
back on,please call for service or professional maintenance
agent to have further check.
This safety device may have been switched off during

6
transport, if soreset the thermal cut-off following the above
instructions.
THERMAL CUT-OUT
The appliance is fitted with a thermal cut-out to have double
safety protection .When the wax is boiled dry and the boil dry
protections fails to work ,the thermal cut-out will work ,then the
appliance stops working.
The cut out temperature is 240℃
This thermal cut-out is a disposable part. When this part comes
into effect, it will be broken and cannot be used again. The
appliance should be brought to authorized agent to replace the
thermal cut-out.
CLEANING AND MAINTENANCE
A. Only perform cleaning once the plug has been removed
and thewax melter has completely cooled down.
B. Never immerse the wax melter into water.
C. Pore hot water into the melter, brush sides, Melt the wax
completelythen pour out the water.
D. Do not use any cleaning products which can cause a health
hazard.
E. Use a soft cloth to wipe the urn body dry. Do not use
abrasivematerials to avoid scratches.

7
items
Description
1
Name
ELECTRIC WAX MELTER
2
Model
DT-S005(A)
DT-S005(B)
DT-S005(C)
3
Rating
(s)
220-240V~
50Hz/1200W/
5.0~5.5L
120V~ 60Hz/ 1200W
/
5.0~5.5L
220-240V~
50Hz/1200W/
5.0~5.5L
4
Package
Size
270×270×250mm
270×270×250mm
270×270×250mm
5
G.W：
3.2kg
3.2kg
3.2kg
6
Correct Disposal:
This product is subject to the provision of European
Directive2012/19/EC. The symbol showing a wheelie bin
crossed through indicates that the product requires separate
refuse collection in the European Union. This applies to the
product and all accessories marked with this symbol.Products
marked as such may not be discarded with normal domestic
waste, but must be taken to a collection point for recycling
electrical and electronic devices.
7
FCC Declaration:
This device complies with Part 15 of the FCC Rules.Operation is
subject to the following two conditions: (1)This device may not
cause harmful interference, and(2)this device must accept any
interference received, including interference that may cause
undesired operation.

8
PRECAUTIONS
A. Thermostat installation instructions.
B.The lid must be placed when the wax is dissolved.
C.Do not mix with water when melting wax. Wipe the water off
before adding wax beans.
Address：Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi
Shanghai
Imported to AUS: SIHAO PTY LTD, 1 ROKEVA STREETEASTWOOD
NSW 2122 Australia
Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim
Place, Rancho Cucamonga, CA 91730
Made In China

Technical Support and E-Warranty Certificate
www.vevor.com/support