VEVOR TLM38388 User manual

E-mail: CustomerSe[e-mail]
MULTIFUNCTIONAL DIGITAL
HEAT PRESS MACHINE
USER GUIDE

MULTIFUNCTIONAL DIGITAL
HEAT PRESS MACHINE
This is the original instruction, please read all manual instructions carefully before operating. VEVOR
reserves clear interpretation of our user manual. The appearance of the product shall be subject to the
product you received. Please forgive us that we won't inform you again if there is any technology or
software updates on our product.
NEED HELP? CONTACTUS!
Have product questions? Need technical suppo? Please feel free to contact us:
CustomerSe[email protected]
01 02
CONTENTS
REPLACE BAKING COASTER
HEAT PRESS MACHINE PARTS INTRODUCTION 3
PARTS LIST 4
ASSEMBLY & USE STEPS 5
INTELLIGENT TEMPERATURE CONTROLLER OPERATION METHOD 6
Ⅰ. PREPARATION BEFORE USING 6
Ⅱ. SET TEMPERATURE REQUIRED 6
REPLACE BAKING TRAY MAT 8-9
REPLACE BAKING CAP MAT 10-12
13-14
Ⅲ. PRINTING METHODS 15
Ⅳ. TROUBLE SHOOTING FOR TRANSFER QUALITY 15-16
.................................................................................................................................
................................................................................................................................
.................................................................................................................................
.............................................................................................................................
............................................................................................................................
...............................................................................................................................................
................................................................................

PARTS LIST
04
HEAT PRESS MACHINE PARTS INTRODUCTION
TEMP
TEMP
TIME SET
TIME
overload
protector design
power switch
display
temperature light
set light
time light
minus mode plus sta
best pressure for heat press
rotation lock screw swiveling pressure adjustment
spring
T-shi: 3/8-1/2”
other object: 3/16”
3/16”
spring
object
03
1PC
1PC
A Phillips screwdriver can be turned into a slotted
screwdriver by rotating it 180 degrees
5in1 Heat Press
6in1 Heat Press
8in1 Heat Press
Pa A Pa B Pa C Pa D Pa E Pa F Pa H Pa G Pa I Pa J
√ √ √ √ √ √ √
√ √ √ √ √ √ √ √
√ √ √ √ √ √ √ √ √ √
1PC 1PC
1PC 1PC
AB
CD
1PC
EF
1PC
G
1PC
1PC
H
1PC
I
1PC
J

INTELLIGENT TEMPERATURE CONTROLLER OPERATION METHOD
Ⅱ.Set temperature required
Ⅰ
.Preparation before Using:
Check the connection between power plug and electrical socket of electrical cabinet.
Be sure to operate with safe ground wire!!!
Heat press element must be securely plugged into the machine before you switch the machine
on.Plug your electrical cord into the machine. Plug electrical socket into wall plug.
temperature and timing setting.(Temperature is measured in Degrees Fahrenheit.)
Press the “MODE”button ONCE,see the “set light” turning red.Then press
the “plus/minus key” to set the initial heating temperature.
1.
2.
A.Initial Temperature Setting ( Range:200-450℉)
Press the “MODE” button for THE SECOND TIME;see the “temperature light” turning
red.Then press the “plus or minus key” to set the highest heating temperature.
B.Highest Temperature Setting ( Range:93-232℃)
Press the “MODE” button for THE THIRD TIME;see the”time light” turning red.
Then press the “plus or minus key” to setthe proper heating time.
C.Proper Heating Time Setting ( Range:0-999 sec.)
Press
Object
Mugs
Tiles
Metal board
Plate
230
230
230
230
330
330
300
355
40
40
40
150
Initial
Temperature
Highest
Temperature
Proper Heating
Time ( s )
Sublimation paper:30-50s
230 355
06
ASSEMBLY & USE STEPS
1
2 3
4 5
Tighten knob.
Rotate the heat transfer board
to the side.
Pull out the mat below, place the
the pattern on the clothes.
Turn this adjustment switch
to adjust the pressure.
05
Turn the power.
on by flipping the on/off Switch on.
D. Fahrenheit to Celsius
After turning on the hot stamping machine, press the+and - buttons simultaneously for about five seconds.
When PAE is displayed, press the MODE key to display (F-C), and change F to C in the time display gear,
so that Fahrenheit is converted to Celsius.

1
2
Pluck the plug.
Rotate the heat transfer board to the side.
Replace Baking Tray Mat
0807
Turn o the power and pull out the mat. It is recommended to wear heat-resistant gloves
when removing clothes or remove them after 2-3 minutes. Be careful of hot heat.
Printed pattern
Note
• The machine has a self -locking function for temperature setting.
---If the staing temperature is set to 340°F,the machine will automatically limit the
maximum temperature setting range from 340 to 430°F.
---Conversely,if setting the maximum temperature as 250°F at rst,the machine will
automatically limit the staing temperature setting range from 200 to 250°F.
• Initial heating temperature always=<Highest heating temperature
Printed clothes
Press the “MODE”button for THE FOURTH TIME;nish the setting , The set light is on,
and the temperature will continue to rise. When the set maximum temperature is reached, the
countdown stas. After the countdown ends, the "BEEF" sound will be emitted, the indicator
light will turn o, and the operation is complete.and the machine stands by to work.
D.Finish the Setting and Stands by to Work
Use a Phillips screwdriver to unscrew the screws in the two holes on the
pressure plate to replace the accessories

2
1
Replace Baking Cap Mat
Pluck the plug.
Rotate the heat transfer board to the side.
10
Select the appropriate size baking pan mat ( Pa A or B ).
3
4
Plug in.
Patterned plate.
Replace Baking Tray Mat
AB
09

Use the screwdriver 4 to tighten the 2 screws just
removed and put the cap on. Shaped hat
6
Replace Baking Cap Mat
12
Replace Baking Cap Mat
Loosen the bottom
screw and remove.
Lift the cushion up
4
5
3
11
Unscrew the four butterfly screws at the bottom

E
1
(Tighten the screws on both sides.
We suggest to tighten the screws on
the side
①
screws on the side②)
2
Adjust the tightness.
Plug in.
Shaped cup
Replace Baking Coaster
I or J
E
①②
1413
2
1
Select the appropriate size
(Tighten the screws on both sides. We suggest
to tighten the screws on the side①
then tighten the screws on the side②)
Adjust the tightness.
Plug in.
Shaped cup
Replace Baking Coaster
E
G
F or H
E
①②
Install G to Part E.
baking coaster (Part F or H)