WAC Lighting 5221 User manual

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2019
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER BEFORE BEGINNING.
- Read all instructions before installing.
- System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
- When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
- Retain installation instructions for future maintenance reference.
- Risk of electric shock. Install all luminaires 10 feet (3.05m) or more from a pool, spa, or fountain.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by WAC Lighting. Substitution of parts or accessories not designated for use with this product by WAC Lighting
could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts
are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
- Lisez toutes les instructions avant l’installation.
- Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
- Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
- Risque de choc electrique. Installez tous les luminaires de (3.05m) (10 ft.) ou plus d’une piscine, d’un spa ou d’une fontaine.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement avec
les pièces et/ou accessoires fournis pour être utilisés avec les produits WAC Lighting. Remplacer des pièces ou accessoires non conçus pour ce
produit WAC Lighting pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons aux
clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec un
chion humide.
INSTALLATION INSTRUCTIONS
Adjustable Beam Wall Wash
5221
THE INSTRUCTIONS APPLY TO THE MODEL BELOW:
HARDWARE
Weatherproof Wire Nut
7EAC352401
Qty: 2 pcs
Mounting Stake
7TCD359501BW
Qty: 1 pc
Horizontal Shroud Assembly
5220-HSHR-BK
5220-HSHR-BZ
5220-HSHR-BBR
Qty: 1 pc
Hex Key
7MPE155003
Qty: 1 pc
5221

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2019
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
STEP 1: DETERMINING THE LOCATION
1. Make sure the main power is o.
2. At the point of installation, mount the stake by placing a piece
of wood on the stake and hammering the wood. Hammer till the
bottom of the ring is ush with the ground.
3. In the case of hard soil, dig a hole and place the stake in so that the
bottom of the ring is ush with the ground. Fill the rest of the hole
with the removed soil and pack it tight to secure the stake.
4. Screw the xture onto the stake provided, leading the wire from
the xture through the wire slot in the stake.
STEP 2: WIRING THE FIXTURE
NOTE: Transformer is required to power the xture (sold separately).
1. Cut the power supply wire from the transformer at the location of
the xture.
2. Separate the power supply wire into two individual wires by lightly
pulling on each side so that a couple of inches are separated.
3. Strip o ½ inch of the insulating material from each wire and
connect one to each of the wires from the xture using the
outdoor rated direct burial wire nuts provided.
STEP 3: INSTALLING THE FIXTURE
1. Screw the xture onto the stake provided, leading the wire from
the xture through the wire slot in the stake.
2. If desired, bury the wire by digging a small trench. Close the
trench by applying an inward force to both sides of the trench.
3. Repeat steps for other xtures in the same electrical circuit.
4. Turn the main power supply back on and make sure the xtures
light up.
INSTALLATION INSTRUCTIONS
Adjustable Beam Wall Wash
5221
Light Fixture
Wire Slot
Mounting Stake
Fixture Lead Wire
Transformer
NOTE: To install multiple xtures, also connect
the power supply wire of each additional xture
to the connection described in Step 3 of the
previous xture.
Transformer
NOTE: To install multiple xtures, follow the diagram above.

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2019
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
STEP 4: AIMING THE FIXTURE
1. Tilting: Loosen the joint screw and adjust the head of the xture to
the desired direction before retightening the screw.
2. Loosen the mounting knob and rotate the xture to the desired
position before retightening the knob.
INSTALLATION INSTRUCTIONS
Adjustable Beam Wall Wash
5221
STEP 5: DIMMING ADJUSTMENT
1. Use a Philips head screwdriver to adjust the dimming dial.
2. Rotate until the arrow on the dial is pointed at the desired wattage.
The wattage may be adjusted to the pre-existing tabs or any value
in between.
3. The lower the wattage, the dimmer the xture will be.
4. Please refer to the yellow tag that is included in the packaging to
determine the size of the required transformer.
STEP 6: BEAM ANGLE ADJUSTMENT:
1. Note the three pre-determined beam angles on the beam angle
changing dial.
2. Use the provided Hex Key to slightly loosen the set screw one or
two turns. Do not remove set screw from the xture.
CAUTION: Do not remove set screw from the xture.
It should only be removed from the xture for servicing.
Consult factory for service instruction.
3. Hold the xture body and rotate the dial until the arrow is aligned
with the desired beam angle. This beam angle may be one of the
pre-determined markings or any number in between.
CAUTION: Keep the arrow marking on the xture body between
the beam angle range.
4. Tighten the set screw until it stops. Do not over tighten.
Set Screw
Beam Changing Dial
Beam Angle Markin
g
Fixture Body
Rotation
NEMA
4X3
NEMA
5X4
NEMA
6X5
4x3
(60
H x 35 V)
5x4
(90
H x 60 V)
6x5
(120
H x 90 V)
Rotating
Joint Screw
Mounting Knob
Tilting
26
22
15
7
3

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2019
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
STEP 7: VERTICAL FIXTURE HEAD ROTATION ADJUSTMENT
1. Note the xture head can be rotated 90 degrees to achieve vertical
wall wash applications.
2. Hold xture body with one hand and rotate the xture head with
another hand to 90 degree.
3. Loosen thumb screw and swap the horizontal shroud with a
vertical shroud.
NOTE: Vertical shroud is not provided (sold separately).
INSTALLATION INSTRUCTIONS
Adjustable Beam Wall Wash
5221
Rotation
NEMA
4X3
NEMA
5X4
NEMA
6X5
5x6
(90
H x 120 V)
3x4
(35
H x 60 V)
4x5
(60
H x 90 V)
Fixture Head
Fixture Body
Horizontal Shroud
Thumb Screw
Vertical Shroud
(Not Provided)
ACCESSORIES
1. COLOR LENS:
Colored lenses come in red, blue, green, amber, frosted, and beam
spread to lter the light coming out of the xture.
Installation: Push the lens onto the center of the clip and push
them onto the front of the xture.
LENS-3X5-xxx
LENS CLIP
(Included in LENS-3x5-xxx)

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2019
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTIONS
Adjustable Beam Wall Wash
5221
ACCESSORIES
2. SURFACE MOUNT ACCESSORY:
The surface mount accessory is used to mount the xture to a hard
surface like wood or cement or as alternative to the mounting stake.
Installation: Mount the accessory to a hard surface using No. 10
Philips head screws that are at least half an inch long. If mounting
on concrete or similar surface, rst use a plastic anchor sized
for No. 10 screws. If mounting on a soft surface rst attach the
included spikes.
Create a route underneath the accessory for your wire to travel
through. Lead your wire through the created route and screw your
xture onto the surface mount accessory.
3. TREE MOUNT ACCESSORY:
The tree mount accessory is a way for xtures to be mounted on the
trunk or a branch of a tree while minimizing damage to the tree.
Installation with Wood Screw Bolt:
1. Mark the screw hole locations at the point of installation.
2. Thread one hex nut from the at side of wood screw bolt
until end of threaded.
3. Use a wrench to screw the bolt into the tree until
unthreaded portion of the bolt meets the surface of the
tree (Do this for all three bolts).
4. Place the tree mount junction box onto the bolts and
secure it using additional hex nuts.
5. Attach light xture and lead wire through the junction box.
Place all wire nuts into the tree mount junction box.
Installation with Wood Screw Bolt:
1. Mount the junction box mounting bracket onto the back of the
tree mount junction box with 4 screws (Leave the wood screw
bolts as they are not required for this installation).
2. Put the ratchet strap though the junction box mounting bracket
and tight the strap onto the tree.
3. Secure and tighten the strap by using the ratchet.
4. Attach light xture and lead wire through the junction box.
Place all wire nuts into the tree mount junction box.
Removable Spike
No. 10 Tapping Screw
Surface Mount Canopy
Fixture
Hex Nut
Tree Mount Junction Box
Wood Screw
Tree
Fixture
5000-TCL
Tree Mount Junction Box
5000-TST
Junction Box
Mounting Bracket
5000-TST
Junction Box
Mounting Screw
Tree
5000-TST
Strap
5000-TST
Ratchet
NOTE: Due to tree growth, annual inspection of the strap is required to ensure that the xture is secure. Failure to do so may cause the
xture to fall from the tree, or damage to the xture or other items.