WAC Lighting LED-350MA03-RB User manual

INSTRUCTIONS : CLASS 2 CONSTANT CURRENT POWER SUPPLY
MODEL : LED-350MA03-RB
CAUTION -To reduce the risk of fire, electric shock or injury to persons:
•Always turn off power at main switch prior to installation.
•System intended for installation by a qualified electrician, in accordance with NEC and local regulations.
Consult with local inspector to assure compliance.
•For use with LED button lights only.
Model LED-350MA03-RB
Input Voltage 120Vac,50/60Hz
Input Current Max 0.2A
Output Current 350Ma
Each Port Output Voltage 2-12V DC
Each Port Load 3x1W LED Light
Each Port Load Lead Wires 12-22AWG
Output Port 1
FEATURES:
•350mA Constant Current for LED’s optimized and stable performance.
•Powers one LED Button lights
•Special circuit design to protect LED from high voltage pulse.
Driver will automatically shut off if the fixtures are not properly wired. In this event, unplug and check the wiring and
then plug it in again.
INSTALLATION:
1. Remove both covers.
2. Input wiring - use only one knock out holes. Connect building wires to like color transformer wires with wire nuts.
Building ground wire may be green or un-insulated, and attaches to green wire from transformer box.
3. Output wiring - Push down one set of the wiring terminals and insert fixture’s red wire into the “+” terminal
and the black wire into the “-” terminal.
4. Secure the covers by tightening the two screws.
5. The product should be installed on the either internal or external surface of any indoor construction.
Retain these instructions for future service and adjustments
44 Harbor Park Drive, Port Washington, NY 11050
Tel: [phone] Fax [phone]
www.waclighting.com

INSTRUCTIONS : CLASS 2 CONSTANT CURRENT POWER SUPPLY
MODEL : LED-350MA09-RB
CAUTION -To reduce the risk of fire, electric shock or injury to persons:
•Always turn off power at main switch prior to installation.
•System intended for installation by a qualified electrician, in accordance with NEC and local regulations.
Consult with local inspector to assure compliance.
•For use with LED button lights only.
Model LED-350MA09-RB
Input Voltage 120Vac,50/60Hz
Input Current Max 0.2A
Output Current 350Ma
Each Port Output Voltage 2-12V DC
Each Port Load 3x1W LED Light or 1-3 PCS LED
Each Port Load Lead Wires 12-22AWG
Output Port 3
FEATURES:
•350mA Constant Current for LED’s optimized and stable performance.
•Powers up to 3 LED Button lights
•Special circuit design to protect LED from high voltage pulse.
Driver will automatically shut off if the fixtures are not properly wired. In this event, unplug and check the wiring and
then plug it in again.
INSTALLATION:
1. Remove both covers.
2. Input wiring - use only one knock out holes. Connect building wires to like color transformer wires with wire nuts.
Building ground wire may be green or un-insulated, and attaches to green wire from transformer box.
3. Output wiring - Push down one set of the wiring terminals and insert fixture’s red wire into the “+” terminal
and the black wire into the “-” terminal.
4. After connecting all the LED fixtures, switch (S1-S3) should be at “ON” position for all terminals connected to a Button
light. Terminals not connected to a button light should be at “OFF” position.
5. Secure the covers by tightening the two screws.
6. The product should be installed on the either internal or external surface of any indoor construction.
Retain these instructions for future service and adjustments
44 Harbor Park Drive, Port Washington, NY 11050
Tel: [phone] Fax [phone]
www.waclighting.com

INSTRUCTIONS : CLASS 2 CONSTANT CURRENT POWER SUPPLY
MODEL : LED-350MA12-RB
CAUTION -To reduce the risk of fire, electric shock or injury to persons:
•Always turn off power at main switch prior to installation.
•System intended for installation by a qualified electrician, in accordance with NEC and local regulations.
Consult with local inspector to assure compliance.
•For use with LED button lights only.
Model LED-350MA12-RB
Input Voltage 120Vac,50/60Hz
Input Current Max 0.2A
Output Current 350Ma
Each Port Output Voltage 2-12V DC
Each Port Load 3x1W LED Light or 1-4 PCS LED
Each Port Load Lead Wires 12-22AWG
Output Port 4
FEATURES:
•350mA Constant Current for LED’s optimized and stable performance.
•Powers up to 4 LED Button lights
•Special circuit design to protect LED from high voltage pulse.
Driver will automatically shut off if the fixtures are not properly wired. In this event, unplug and check the wiring and
then plug it in again.
INSTALLATION:
1. Remove both covers.
2. Input wiring - use only one knock out holes. Connect building wires to like color transformer wires with wire nuts.
Building ground wire may be green or un-insulated, and attaches to green wire from transformer box.
3. Output wiring - Push down one set of the wiring terminals and insert fixture’s red wire into the “+” terminal
and the black wire into the “-” terminal.
4. After connecting all the LED fixtures, switch (S1-S4) should be at “ON” position for all terminals connected to a Button
light. Terminals not connected to a button light should be at “OFF” position.
5. Secure the covers by tightening the two screws.
6. The product should be installed on the either internal or external surface of any indoor construction.
Retain these instructions for future service and adjustments
44 Harbor Park Drive, Port Washington, NY 11050
Tel: [phone] Fax [phone]
www.waclighting.com

INSTRUCTIONS : CLASS 2 CONSTANT CURRENT POWER SUPPLY
MODEL : LED-350MA09-DIM-RB
CAUTION -To reduce the risk of fire, electric shock or injury to persons:
•Always turn off power at main switch prior to installation.
•System intended for installation by a qualified electrician, in accordance with NEC and local regulations.
Consult with local inspector to assure compliance.
•For use with LED button lights only.
Model LED-350MA09-DIM-RB
Input Voltage 120Vac,50/60Hz
Input Current Max 0.15A
Output Current 350mA
Each Port Output Voltage 2-12V DC
Each Port Load 3x1W LED Light or 1-3PCS LED
Each Port Load Lead Wires 12-22AWG
Output Port 3
FEATURES:
•350mA Constant Current for LED’s optimized and stable performance.
•Powers up to 3 LED Button lights
•Special circuit design to protect LED from high voltage pulse.
Driver will automatically shut off if the fixtures are not properly wired. In this event, unplug and check the wiring and
then plug it in again.
INSTALLATION:
1. Remove both covers.
2. Input wiring - use only one knock out holes. Connect building wires to like color transformer wires with wire nuts.
Building ground wire may be green or un-insulated, and attaches to green wire from transformer box.
3. Output wiring - Push down one set of the wiring terminals and insert fixture’s red wire into the “+” terminal
and the black wire into the “-” terminal.
4. Secure the covers by tightening the two screws.
5. The product should be installed on the either internal or external surface of any indoor construction.
Retain these instructions for future service and adjustments
44 Harbor Park Drive, Port Washington, NY 11050
Tel: [phone] Fax [phone]
www.waclighting.com

\
INSTRUCTIONS : CLASS 2 CONSTANT CURRENT POWER SUPPLY
MODEL : LED-350MA12-DIM-RB
CAUTION -To reduce the risk of fire, electric shock or injury to persons:
•Always turn off power at main switch prior to installation.
•System intended for installation by a qualified electrician, in accordance with NEC and local regulations.
Consult with local inspector to assure compliance.
•For use with LED button lights only.
Model LED-350MA12-DIM-RB
Input Voltage 120Vac,50/60Hz
Input Current Max 0.2A
Output Current 350Ma
Each Port Output Voltage 2-12V DC
Each Port Load 3x1W LED Light or 1-4 PCS LED
Each Port Load Lead Wires 12-22AWG
Output Port 4
FEATURES:
•350mA Constant Current for LED’s optimized and stable performance.
•Powers up to 4 LED Button lights
•Special circuit design to protect LED from high voltage pulse.
Driver will automatically shut off if the fixtures are not properly wired. In this event, unplug and check the wiring and
then plug it in again.
INSTALLATION:
1. Remove both covers.
2. Input wiring - use only one knock out holes. Connect building wires to like color transformer wires with wire nuts.
Building ground wire may be green or un-insulated, and attaches to green wire from transformer box.
3. Output wiring - Push down one set of the wiring terminals and insert fixture’s red wire into the “+” terminal
and the black wire into the “-” terminal.
4. Secure the covers by tightening the two screws.
5. The product should be installed on the either internal or external surface of any indoor construction.
5
Retain these instructions for future se
rvice and adjustments
44 Harbor Park Drive, Port Washington, NY 11050
Tel: [phone] Fax [phone]
www.waclighting.com