WAC Lighting Paloma MO-LED512 User manual

WAC Lighting
www.waclighting.com
Phone [phone] • Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY, 2016 1
INSTALLATION INSTRUCTION
Paloma - LED Monopoint
MO-LED512
SAFETY INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the“OFF”position and unscrew the fuse(s) or switch“OFF” the
circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the“OFF”position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or
broken. Failure to follow this instruction could invalidate the UL/CUL listing of this xture.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt («OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne
les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation UL/CUL du luminaire.
INSTALLING LAMP: Fig.1)
1. Loosen the three canopy screws, twist and separate
the canopy cover from the base plate.
(keep screws on base plate)
2. Remove a knock out from the base plate.
3. Attach the base plate to the surface using slotted holes
for mounting screws (supplied).
4. Connect xture wires to AC power wire,
with wire nuts (supplied).
5. Connect ground wire to the green wire from xture.
6. Mount the canopy to the base plate by twisting
key holes over three screws in base plate.
7. Tighten screws to secure canopy.
8. After the light is on, rotate the luminaire body
horizontally or vertically to aim properly.
Note: All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction could invalidate the UL/CUL listing of this xture.
FIG.1
±90°
from
Vertical
Position
355°
Canopy
Base
Plate
Canopy
Mounting
Screw
Base Plate
Mounting
Screw
Electrical Data
INPUT VOLTAGE 120-277V AC, 50/60Hz
INPUT CURRENT (MAX.) 0.09A
DIMMING ELV

WAC Lighting
www.waclighting.com
Phone [phone] • Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY, 2016 2
ACCESSORIES: Fig. 2
1. Take out the Front Cap by rotating it counter clockwise.
2. Push the original LENS out from the Front Cap and replace it with the new LENS.
3. Put the Front Cap back onto the xture.
FIG.2
LENS-16
Front Cap
INSTALLATION INSTRUCTION
Paloma - LED Monopoint
MO-LED512