WAC Lighting WTK-6010 Series User manual

WAC Lighting
www.waclighting.com
Phone [phone] • Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY, 2017 1
INSTALLATION INSTRUCTION
Lucio - LED Track Luminaires
WTK-6010*/WTK-6022*/WHK-6010*/WHK-6022*
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local
regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF”position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the“OFF”position.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en
position d’arrêt (« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the UL listing of this xture.
Overview:
Fixtures are designed for use on WAC Lighting’s W track systems.
LED TRACK LUMINAIRE TRACK SYSTEM
WTK-6010*/ WTK-6022* WTK 120V W Track
WHK-6010*/ WHK-6022* WHK 277V W Track
Installing on Track
1. Make sure that the lock switch is in the unlock position and the circuit selection handle is in the o position. (See to Fig 1)
2. Align the alignment tab bump on the adapter with the groove/slot on the track (see Fig 2). Once aligned,
insert adapter into the track
W Track
Switch handle
(power o position)
Lock switch
(unlock position)
Adapter
Groove
Alignment tab
Fig 2
Fig 1

WAC Lighting
www.waclighting.com
Phone [phone] • Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY, 2017 2
INSTALLATION INSTRUCTION
Lucio - LED Track Luminaires
WTK-6010*/WTK-6022*/WHK-6010*/WHK-6022*
3. To secure the xture to the track turn the lock switch to its locked position.(See Fig 3)
4. Select the circuit you want the luminaire to be powered on by rotating the circuit selection handle to circuit 1 or 2. (See View A)
5. Switch the main fuse breaker and circuit breaker to “ON “position.
6. Place the wall switch in the“ON “position
Positioning the Fixture
7. After the light is on, rotate the luminaire’s body horizontally and vertically to aim it properly.
Vertical aiming includes index markings. (See Fig 4)
2
1
Circuit selecting handle
1. Power on at circuit 1
2. Power on at circuit 2
Lock switch
(lock position)
View A
View AFig.3

WAC Lighting
www.waclighting.com
Phone [phone] • Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY, 2017 3
ACCESSORIES
With the power o, follow steps below. Reference specication sheet for compatible accessories.
Glare Control Accessory Installation:
Step 1: Gently move front cap forward to
remove it. One torsion spring will remain
engaged while other will slide out
completely. (See Fig 5)
Step 2: Insert glare control accessory
through the front frame.
(See Fig 6)
Step 3: Reinstall front cap back in place.
Ensure torsion spring securely goes back
into spring slot on xture (See Fig 7)
Lens Accessory Installation:
Step 1: Gently move front cap forward
to remove it. (See Fig 8)
Step 2: Rotate lens holder with ears
counterclockwise to remove it.
(See Fig 9)
Step 3: Replace existing lens with
new lens. (See Fig 10)
INSTALLATION INSTRUCTION
Lucio - LED Track Luminaires
WTK-6010*/WTK-6022*/WHK-6010*/WHK-6022*
Fig.5
Fig.8
Fig.6
Fig.9
Fig.7
Fig.10
Front Cap
Torsion Spring
Glare control
accessory.
Snoot shown
lens holder
Ear on lens holder

WAC Lighting
www.waclighting.com
Phone [phone] • Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY, 2017 4
INSTALLATION INSTRUCTION
Lucio - LED Track Luminaires
WTK-6010*/WTK-6022*/WHK-6010*/WHK-6022*
Change LENS
Step 4: Align the triangle mark on
the lens holder to the one on the
reector holder, then rotate clockwise
to lock it. (See Fig 11)
Step 5: Reinstall front cap back in place.
Ensure torsion spring securely goes back
into spring slot on xture (See Fig 12)
Fig.11 Fig.12
Mark on lens holder
Mark on
reector holder