WAC Lighting Falcon Series User manual

INSTALLATION INSTRUCTIONS
Falcon Wall Washer
Model：TL61W/TL62W/TL63W
Headquarters
44 Harbor Park Drive, Port Washington, NY
Phone [phone] •Fax [phone]
www.waclighting.com
WAC Lighting (Shanghai)
14 Lane 299, Bi Sheng Road Shanghai 201204
Phone [phone] •Fax [phone]
www.waclighting.com.cn
WAC Lighting - International sales
Room 3207-3208, Building 4,Tian An Cloud Park,
ShenZhen, Guangdong 518129
www.waclighting.io
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. April 22, 2019 1 / 3
WARNING
IMPORTANT: NEVER attempt any work without shutting off the electricity.
·Read all instructions before installing.
·Fixtures are designed for use on WAC Lighting’s track systems. They may also be used on other
manufacturer’s brand of track (consult factory for compatibility).
Track rating: Input: 220-240V ~, Current max: 16A, Load max: 3680W.
·Suit for dry location, do not install in damp or wet locations.
·System is intended for installation by a qualified electrician in accordance with the National Electrical Code
and local regulations.
·Light Source is not replaceable. (It should be replaced the whole fixture when the life of light source ends.)
·Leave the instructions for users/customers for future reference.
Caution:
·Please switch off the power before fixture installing / maintainance / accessory exchanging.
Ⅰ. Installing on Track
1. Ensure the “Power Knob”and Adaptor are parallel, and “Phase switching Knob”is located on the state of
“Ⅰ”/ “Ⅱ”or “Ⅲ”.
2. Make sure the convexity on the adaptor box is at the same side with the slot on the track. Fit the adaptor box
into the track.
Phase switching Knob
Power Knob
Slot
Convexity
Phase switch：
“Ⅰ”indicate fixture is connect on phase1.
“Ⅱ”indicate fixture is connect on phase2.
“Ⅲ”indicate fixture is connect on phase3.

INSTALLATION INSTRUCTIONS
Falcon Wall Washer
Model：TL61W/TL62W/TL63W
Headquarters
44 Harbor Park Drive, Port Washington, NY
Phone [phone] •Fax [phone]
www.waclighting.com
WAC Lighting (Shanghai)
14 Lane 299, Bi Sheng Road Shanghai 201204
Phone [phone] •Fax [phone]
www.waclighting.com.cn
WAC Lighting - International sales
Room 3207-3208, Building 4,Tian An Cloud Park,
ShenZhen, Guangdong 518129
www.waclighting.io
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. April 22, 2019 2 / 3
3. Rotate “Power Knob”90 degrees to connect the power.
Remark: The procedure is opposite for taking down and installation the track head.
Ⅱ. Brightness Adjustment
Ⅲ. Fixture Adjustment
Fixture body is adjustable, Angle adjustment: Horizontal 0°-365°，Vertical 0°-90°
Rotate the button to
adjust the brightness
of the lighting.
Rotate clockwise to
increase the bright
-ness.
Rotate counterclockwise
clockwise to reduce the
brightness.
Rotate 0 °- 365 °
horizontally on this axis.
Rotate 0 °- 90 °
vertically on this axis.
Power Knob

INSTALLATION INSTRUCTIONS
Falcon Wall Washer
Model：TL61W/TL62W/TL63W
Headquarters
44 Harbor Park Drive, Port Washington, NY
Phone [phone] •Fax [phone]
www.waclighting.com
WAC Lighting (Shanghai)
14 Lane 299, Bi Sheng Road Shanghai 201204
Phone [phone] •Fax [phone]
www.waclighting.com.cn
WAC Lighting - International sales
Room 3207-3208, Building 4,Tian An Cloud Park,
ShenZhen, Guangdong 518129
www.waclighting.io
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. April 22, 2019 3 / 3
Ⅳ. Accessories
1. Rotate the fixture body down to the right position, Open the front cover with a small slotted screwdriver
from the gap between the front cover and fixture body, and then pull out the front cover by hand.
2. Hold and push open the Spring Clip, take out the optic Lens or Film.
Note: There is a chamfer on the front cover and optic part, please use it to confirm the direction.
3. After exchange the optic part, Push back the front cover to the fixture body like below picture.
Ⅴ. MAXIMUM LOAD
1. The drawings below show the maximum permissible mechanical load by W tracks for luminaires or other
loads in relationship to the fixation or suspension point. It includes both of the weights of the track system.
2. The maximum load about single adapter is 10kg.( Fixture body is fixed on adapter on the right location.)
Spring Clip
Diffuse Film
Chamfer
Gap