WAC Lighting HR-3LED-H20A User manual

WAC Lighting
www.waclighting.com
Phone [phone] • Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. AUGUST, 2014
INSTALLATION INSTRUCTION
3.5” Shallow Recessed Housing and Trims
HR-3LED-H20A
SAFETY INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting o the electricity.
• Read all instructions before installing.
• System is intended for installation by a qualied electrician in accordance with the National Electrical Code and
local regulations.
• Place the wall switch in the“OFF”position.
• Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that
control the power to the space that you are working on.
CAUTION:
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts
that are worn out or broken. Failure to follow this instruction could invalidate the ETL/cETL listing of this xture.
AVERTISSEMENT
IMPORTANT : COUPEZ L’ÉLECTRICITÉ AVANT TOUTE MANIPULATION.
• Lisez toutes les instructions avant d’installer.
• Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et
les règlements locaux.
• Placez l’interrupteur mural en position d’arrêt (« OFF »).
• Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en
position d’arrêt (« OFF »).
MISE EN GARDE
Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez
pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation
ETL/cETL du luminaire.
OVERVIEW:
Housing is new construction IC, AIRTIGHT. Housing requires a trim. Please check the website for compatible trim choices.
HOUSING INSTALLATION:
1. Install housing using two hanger bars provided, align the bottom of the hanger bar with the bottom of the wood joist.
Secure the “screw-nail” on each end by screw-driver or by hammer(See FIG.1 detail A). Slide xture along hanger bar into
desired location, use locking screws to secure (See FIG.1 detail B). For grid installation, hanger bars should be supported
on grids. (See FIG.2)
2. To shorten hanger bars to t in a shorter distance, snap o one or more sections of the hanger bars (See FIG.3).
3. Remove spring latched junction box cover and connect xture wires to building wires: insert each supply wire into
appropriate junction box connector. Connect black xture wire to hot, white xture wire to neutral and green xture wire
to ground (See FIG.4). Place all wiring and connectors back in junction box and replace the junction box’s cover.
Snap o one section
t in a 12” joist

WAC Lighting
www.waclighting.com
Phone [phone] • Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. AUGUST, 2014
INSTALLATION INSTRUCTION
3.5” Shallow Recessed Housing and Trims
HR-3LED-H20A
TRIM INSTALLATION
1. Raise the trim to housing, depress trim spring clips and push the trim assembly up until the trim ring is ush to
the ceiling (See FIG.5 and FIG.6).
INVISIBLE TRIM INSTALLATION
1. Raise the invisible trim frame aligning tab to slot in housing, and put plastic shield inside (See FIG.7).
2. Secure the invisible trim frame to the housing, ush up against the ceiling using the screws supplied (See FIG.8).
3. Apply plaster or spackle over Invisible frame and sand surface when dry for a nished look (See FIG.9).
4. Remove the plaster shield when nishing is completed (See FIG.10).
5. Raise the invisible trim assembly up to the trim frame until the trim ring is ush to the trim frame (See FIG.11).
INVISIBLE TRIM MODEL
Slot in
housing
HR-3LED-T120
(Round Trim)
HR-3LED-T720
(Square Trim)
Trim Model
Tab
Plaster shield
Remove plaster shield
HR-3LED-TL220
(Round Trim)
HR-3LED-TL820
(Square Trim)

WAC Lighting
www.waclighting.com
Phone [phone] • Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. AUGUST, 2014
INSTALLATION INSTRUCTION
3.5” Shallow Recessed Housing and Trims
HR-3LED-H20A
LED AND DRIVER REPLACEMENT
1. Remove the trim or invisible trim
a. Remove the trim or invisible trim as shown below (See FIG.12 & 13).
To remove trim:
Remove the trim by pulling the trim’s edge
To remove invisible trim:
Remove the invisible trim by gently prying
between the invisible trim and lens
2. Replace LED
a. Disconnect wire connector, rotate the LED module counterclockwise and pull out to remove the
LED module from housing (See FIG.14).
b. Replace the LED by unscrewing the bracket, removing lens and reector. Then, replace the LED (See FIG.15 & 16).
3. Replace Driver
a. Remove the LED module rst (See step 2 and FIG.14), then, loosen wing nuts on the side of driver (See FIG.17).
b. Tilt driver downward and remove from housing (See FIG.18).
c. Remove screws to replace driver with new, rewire according to code and reinstall (See FIG.19).
Trim Invisible Trim
LED Module
Wire
connector Housing
LED
Reector
Lens
Bracket
Screws
Connector
LED
Wing Nuts
Screws