WAC Lighting GATE 12V User manual

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEPT 2019 1
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTIONS
GATE 12V
6651
SAFETY INSTRUCTION
GATE
6651
Mounting Stake
Qty: 1pc
Outdoor Rated Wire Nut
Qty: 2pcs
Hex Key
Qty: 1pc
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER BEFORE
BEGINNING.
- Read all instructions before installing.
- System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local
regulations.
- When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
- Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by WAC Lighting. Substitution of parts or accessories not designated for use with this product by WAC
Lighting could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer
if any parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in
coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
- Lisez toutes les instructions avant l’installation.
- Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
- Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé
seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits WAC Lighting. Remplacer des pièces ou
accessoires non conçus pour ce produit WAC Lighting pourrait causer des dommages corporels ou matériels et pourrait également causer
l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous
recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les
deux semaines avec un chiffon humide.

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEPT 2019 2
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTIONS
GATE 12V
6651
INSTALLATION
1.
2. Excavate a trench for the Mounting Stake.
The Mounting Stake requires approximately a one (1) square
foot hole to facilitate installation.
The excavated trench should be approximately 14” deep,
depending on your local code. This will allow the hex-head
set screw on the Mounting Stake to remain above ground
when the installation is completed.
3. Secure Fixture Mounting Plate onto the Stake Metal Cap by
using the Stake Mounting Screws.
4. Secure the Stake Metal Cap assembly onto the
Mounting Stake by tighten the Cap Mounting Screw
(NOTE: Make sure the Fixture Mounting Plate is
oriented at desired position.)
5. Secure the Bollard Fixture on top of the Fixture
Mounting Plate using the Fixture Mounting Screws.
6. After proper wirings are done by using the outdoor rated
wire stable.
7. Turn the main power supply back on and make sure the
Fixture Mounting Plate
Stake Metal Cap
Bollard Fixture
Fixture Mounting Screw
Stake Mounting Screw
Cap Mounting Screw
Mounting Stake