WAC Lighting HTK-793 User manual

INSTRUCTIONS Line Voltage Track Fixture
Models: HTK-793 HTK-794 HTK-795
Caution:
Read all instructions before installing.
Switch off power before installing or re-lamping.
Do not attempt to energize anything other than a track light fixture.
All installation shall be in accordance with NEC and all local codes.
To reduce the risk of a burn during re-lamping, remove from the track before re-lamping.
Overview:
Fixtures are designed for use on “HT” series WAC Lighting track. They may also be used on other
manufacturer’s brand of track (consult factory for compatibility).
Retain instructions for future reference.
Lamp
ing
:
1. HTK-793 use PAR 20 lamp, 50W max.
HTK-794 use PAR 30 lamp, 75W max.
HTK-795 use PAR 38 lamp, 150Wmax.
2. Insert the PAR lamp by screwing clockwise
into lamp socket.
Fixture Inst
allation:
1. Note the track head contacts, and the polarity groove
running the length of the track.
2. The two contacts should be positioned so that when
rotated, they will face the grooved side of the track (this
is the side with two flat copper wires running i
ts length).
3. Insert adapter into track slot. Pull downward on the
adapter while rotating the adapter 90º.
4. Release the adapter so the locking tab seats in the
track slot.
5. Removal is the reverse procedure. Track heads may
be positioned anywhere along the track length.
6. Not suitable for use on wall mounted track.
Retain these instructions for future service and adjustments
615 South Street, Garden City, NY 11530
Tel: [phone] Fax [phone]
www.waclighting.com

INSTRUCTIONS Line Voltage Track Fixture
Models: JTK-793 JTK-794 JTK-795
Caution:
Read all instructions before installing.
Switch off power before installing or re-lamping.
Do not attempt to energize anything other than a track light fixture.
All installation shall be in accordance with NEC and all local codes.
To reduce the risk of a burn during re-lamping, remove from the track before re-lamping.
Overview:
Fixtures are designed for use on “JT/J2T” series WAC Lighting track.
They may also be used on other manufacturer’s brand of track (consult factory for compatibility).
Retain instructions for future reference.
Lamp
ing
:
3. JTK-793 use PAR 20 lamp, 50W max.
JTK-794 use PAR 30 lamp, 75W max.
JTK-795 use PAR 38 lamp, 150Wmax.
4. Insert the PAR lamp by screwing clockwise into
lamp socket.
Fixture Installation:
7. Note the track has a groove running its length to
indicate polarity.
8. Note the arrow on the locking tab.
9. Insert adapter into track slot and rotate it 90°. The
arrow should point to the grooved side of the track.
10. Make sure the locking tab seats in the track slot.
11. Removal is the reverse procedure. Track heads
may be positioned anywhere along the track length.
Retain these instructions for future service and adjustments
615 South Street, Garden City, NY 11530
Tel: [phone] Fax [phone]
www.waclighting.com

INSTRUCTIONS Line Voltage Track Fixture
Models: LTK-793 LTK-794 LTK-795
Caution:
Read all instructions before installing.
Switch off power before installing or re-lamping.
Do not attempt to energize anything other than a track light fixture.
All installation shall be in accordance with NEC and all local codes.
To reduce the risk of a burn during re-lamping, remove from the track before re-lamping.
Overview:
Fixtures are designed for use on “LT” series WAC Lighting track.
They may also be used on other manufacturer’s brand of track (consult factory for compatibility).
Retain instructions for future reference.
Lamp
ing
:
5. LTK-793 use PAR 20 lamp, 50W max.
LTK-794 use PAR 30 lamp, 75W max.
LTK-795 use PAR 38 lamp, 150Wmax.
6. Insert the PAR lamp by screwing clockwise into
lamp socket.
Fixture Installation:
1. Note the track has a ridge running its length to indicate
polarity.
2. Note the angled edge of the locking tab.
3. Insert adapter into track slot and rotate it 90 º so that
the low side of the locking tab faces the ridged side of
the track.
4. Make sure the locking tab seats in the track slot.
5. Removal is the reverse procedure. Track heads
may be positioned anywhere along the track length.
Note: “LT” series track accepts only W.A.C. track
heads.
Retain these instructions for future service and adjustments
615 South Street, Garden City, NY 11530
Tel: [phone] Fax [phone]
www.waclighting.com