WATSON Edison Rail Accessories User manual

ASSEMBLY
Edison Rail Accessories
V.21.00 06/2021 360.394.1300 watsonfurniture.com

2 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Edison Accessories
Paper Tray
Rail Screen
Personal Shelf
Workshelf, Dual
Planter Box
Pencil Cup
Acrylic Screen
Clamp
Acrylic Screen
Workshelf, Single
Rail Screen
Markerboard
Rail Screen Tech Stand
Rail Team TableRail Round Table
Rail Lamp
*See separate document
Riser Desk

3 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Hardware
Tools
Phillips Drill/Driver
Bit
2mm Hex Drill/
Driver Bit
3mm Hex Drill/
Driver Bit
Additional tools such as a 90 Degree Bit and an 18” Extension are helpful for
some steps
*No torque or ball bits should be used
Electric Drill
M6-1.0x12mm Low
Profile Cap Screw
(0001140)
Hex Head Screw
5/16-18x3.5”
(0002127)
Washer M8, 8.4MM
ID, 32MM OD
(0001567)
Truss Head Panhead
Screw 10x5/8”
(122800)
M6-1.0x8mm Low
Profile Cap Screw
(0001259)
Screw M6 X 6 BHCS
PHIL Zinc (0001314)
Nut 5/16-18 Zinc
(087750)
Screw SMS #10 X 1
Truss Head PH Zinc
(122850)
M4-0.7 X 5mm
Flat Tip Set Screw
(0001612)

4 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Assembly of Edison Rail Accessories is performed in the same manner for both Edison Junior and Edison Senior Rail systems:
accessories are mounted along the slot spanning the top of the rail. Rail modesty side panels (and water tray, Edison Senior only)
must be removed prior to mounting accessories (pages 4 - 5), and reinstalled after mounting accessories (pages 17 - 18).
*Please note Edison Senior is shown for most steps.
General Assembly Notes
Edison Senior Panel Removal
Press down on the rail panels to lower them and reveal the xing
screws on the opposite panel. Remove the #8-32x1/4” thread-
cutting screws (2x per panel) and set aside (a.). Remove the panels
by lifting from the bottom and pulling toward you (b.). Set aside for
reassembly (page 17).
1. a.
b.
Edison Senior Water Tray Removal
Remove the water tray from the rail segment by
unscrewing the two M6-1x12mm screws on either
end of the segment. Set screws and washers aside for
reassembly (page 17).
2.

5 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Edison Junior Panel Removal
Grabbing from the bottom of the screen, pull the screen away.
The magnet that hold the panel in place will disengage and the
panel will become separated from the frame. Reassembly on
page 18.
3.

6 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Mount Rail Round Legs
With the Rail Round table ipped upside
down, place the leg brackets on the
underside of the surface and line up the
bracket holes with the pilot holes in the
surface. Drive (4) wood screws through
each bracket plate into the surface.
Position Accessory on Rail
Place the rail accessory on the top of the rail segment, centering the
accessory legs on the slot at the top of the rail. The Workshelf, Planter
Box, and Rail Round table all attach in the same manner.
Rail Round, Workshelf, and Planter Box Assembly
Truss Head Panhead
Screw 10x5/8”
(122800)
2.
1.

7 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Secure Accessory to Rail
One or both of the rail modesty panels should be removed for this
operation. From the underside of the rail, drive (1) screw through (1) washer
and the slot in the rail into each leg stem of the rail accessory. Complete
this step for each accessory leg. It can be helpful to lift the leg stem in the
air slightly when trying to align the screws.
Hex Head Screw
5/16-18x4”
(0000631)
M8x24mm Washer
(0001266)
3.

8 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Attach the Base to the Surface
Place the surface upside down on the ground.
Position the leg on the underside of the surface
and align the holes of the leg bracket with the
pilot holes in the surface. Secure the base to
the surface using (6) wood screws. Secure the
brackets to the base using (4) wood screws per
bracket.
Position Mounts on Rail
Place the riser mounts onto the rail at the same
distance apart as the brackets on the surface. Slide
the threaded rod through the channel on the top of
the rail. Use a socket wrench to tighten the washer
and nut to the threaded rod. Leave loose enough to
slide the brackets for alignment.
Truss Head Panhead
Screw 10x5/8”
(122800)
Team Table Assembly
1.
2.
Washer M8, 8.4MM
ID, 32MM OD
(0001567)
Nut 5/16-18 Zinc
(087750)

9 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Mount Table to Rail
Screw the rail and table brackets together. Tighten down
the rail bracket bolts once the table is properly placed.
Level the table to the appropriate height by rotating the
round Team Table base.
3.

10 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
The Riser Desk can be mounted to a rail segment either parallel to the rail, or perpendicular. The rst step shows how to mount
the brackets depending on how the customer specied.
Riser Desk Assembly
Mount Legs, Riser Brackets, and Cable Tray to Desk Surface
Place the surface upside down on the ground. Position the legs on the underside of the surface
and align the holes of the leg brackets with the pilot holes in the surface. Refer to diagram (a.) for
parallel mounting, or diagram (b.) for perpendicular mounting. Perform the same actions for the riser
brackets, using the pilot holes on the inside of the leg bracket pilot holes, as shown. Finally, mount
the cable tray using the pilot holes included.
1.
a.
b.

11 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Position Mounts on Rail
Place the riser mounts onto the rail at the same
distance apart as the brackets on the surface. Slide
the threaded rod through the channel on the top of
the rail. Use a socket wrench to tighten the washer
and nut to the threaded rod. Leave loose enough to
slide the brackets for alignment.
2.
Washer M8, 8.4MM
ID, 32MM OD
(0001567)
Nut 5/16-18 Zinc
(087750)
Mount Table to Rail
Screw the rail and table brackets together, using one of four slots in
the surface brackets. A rail with the lowest leveling will mount using
the bottom slot of the surface bracket. For every 1/2” the rail has
been raised, use the next slot up on the bracket. Tighten down the
rail bracket bolts once the table is properly placed.
3.

Fabric & Markerboard Screens: Position Screen on Rail
Place the screen onto the rail, centering the screen along the rail.
Screen and Screen Accessories Assembly
Hex Head Screw 5/16-18 X
4” (0000631)
M4-0.7 X 5mm Flat Tip Set
Screw (0001612)
Acrylic Screens: Attach Clamps
Screw the hex head mounting screws
part way into the acrylic screen clamps to
increase ease of positioning. Slide the clamps
over the acrylic screen in the dened cutouts,
clamps should be ush against acrylic (a.).
Tighten set screws to clamp down onto acrylic
screen. Remove hex head screws to allow for
rail installation (b.). Place the screen onto the
rail, centering the screen along the rail.
1.
2. a.
b.

13 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Attach Screen to Rail
From the underside of the rail, drive (2) screws
through (2) washers and through the slot in the rail
into each internal screen bracket. Complete this step
on both sides of the screen. It can be helpful to lift
the screen in the air slightly when trying to align the
screws. Slide the screen back and forth along the rail
to its final position before fully tightening the screws.
Hex Head Screw
5/16-18x4”
(0000631)
M8x24mm Washer
(0001266)
3.

M6-1.0x12mm Low
Profile Cap Screw
(0001140)
14 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Personal Shelf
This unit is non-handed, the coat hooks and planter
pot can be installed on either side of the unit. Align
the holes in the coat hooks with the holes in the shelf
as shown below. Drive (2) cap screws through the
personal shelf into the coat hooks to secure them in
place.
Planter & Fabric Insert
Next place the planter in the round opening on the
other side of the personal shelf. Finally place the
fabric wrapped insert into the personal shelf over the
coat hooks as shown below.
Screen Accessories Assembly
1.
2.

15 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Mount Screen Accessories to Screen
Hold the screen accessory at a 45 degree angle. Insert the tab at the top of the accessory into the slot located
at the top of the screen. Rock the accessory back to vertical while keeping the tab engaged with the slot at the
top of the spine screen. This will lock the work tool in place, creating a secure connection with the screen.
3.

16 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Mounting Tools
Tools can be mounted on Edison Rail Workshelves and Edison Rail Fabric Screens. Hold the work tool at a 45 degree
angle. Insert the tab on the top of the work tool into one of the slots on the workshelf or top slot in screen. Rock the
work tool back to vertical while keeping the tab engaged with the slot. This will lock the work tool in place, creating a
secure connection.
1.
Tool Instructions

17 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Edison Senior: Side Panels
Attach the panels that were set aside in Step 1 by
lifting and clipping them onto the rail clips. Secure the
panels to the rail using the #8-32x1/4 screws that
were set aside with the panels (2x per panel).
2.
Edison Senior: Water Tray
After accessories are installed, mount drain tray back in
place with the set aside hardware.
1.
Re-installation of Rail Modesty Side Panels

18 EDISON ACCESSORIES ASSEMBLY INSTRUCTIONS
Edison Junior: Side Panels
Holding the bottom handle of the side panel, align the cutouts for the power
with the plug faces in the rail and push against the rail. Magnets will catch and
secure the panel to the rail.
3.