WATSON Edison Senior Rail User manual

ASSEMBLY
V.21.0 06/2021 watsonfurniture.com360.394.1300
Edison Senior Rail

2 EDISON SENIOR RAIL ASSEMBLY INSTRUCTIONS
WARNING - Risk of Fire or Electric Shock. It is possible for this ofce furnishing system to be connected to more than one source of
supply. Disconnect all sources prior to any servicing. A single circuit shall not be powered by more than one source.
WARNING - Electrical connection between rail segments shall be disconnected prior to removal of a mechanical connection.
WARNING - The system may be supplied by a three phase power system with four individual circuits rated at 20 amps/120 volts max-
imum, or as permitted by local code.
WARNING - No more than 12 duplex receptacles shall be supplied by one circuit. (12 segments Two Duplex, 6 segments Four Duplex)
WARNING - For commercial use only.
NOTE - Installation must be in accordance with the National Electrical Code and local codes. Electrically interconnected tables need
to be mechanically connected.
The Edison Senior Rail is ETL listed to UL962
WARNINGS
It is recommended to perform as much of the rail assembly upside-down, keeping in mind how many installers are available to ip
the run right-side up once assembled.
General Rail Assembly Notes
If 1 - 2 installers: ip the rst rail segment upside down and
complete steps 1 & 2. Then ip the rail right side up and continue
with instructions, adding one segment at a time for step 3.
If 3+ installers: complete steps 1-4 with the rail ipped upside
down. Once complete, ip right side up. The length of run will
determine how many installers are needed to perform the ip.

3 EDISON SENIOR RAIL ASSEMBLY INSTRUCTIONS
Edison Senior Rail Components
Rail Segment
End Leg
Mid-Leg Cap
Modesty
Panel
Power
Harness
Mid-Leg
End-Leg Cap
Floor Anchor
Bracket
Gallery End Panel
Gallery End Panel
Joiner Panel
Gallery End Panel
Rail Mount

4 EDISON SENIOR RAIL ASSEMBLY INSTRUCTIONS
Hardware
M6-1.0x12mm Low
Profile Cap Screw
(0001140)
Tools
M6-1.0x100mm
Button Head Cap
Screw (0001247)
8-32x1/4” Thread
Cutting Screw
(121538)
8/32x1/4 Thread
Cutting Screw
(121405)
Floor Anchor Screw
(48013)
Plastic Reusable
Push Rivet
(0000822)
Phillips Drill/Driver
Bit
2mm Hex Drill/
Driver Bit
3mm Hex Drill/
Driver Bit
Additional tools such as a 90 Degree Bit and an 18” Extension are helpful for
some steps
*No torque or ball bits should be used
Electric Drill
Screw M6-1.00 x
12MM BHSCS, Black
(125285)
Screw Thread-Cutting
M4 x 8MM FH PH, Zinc
(0003016)
Screw M6 x 30MM
BHSCS, Black
(0002086)
Screw SMS #10 x
3/4 Truss Head PH,
Black (122875)
Screw M6 x 50MM
Partial Socket, Black
(0003010)

5 EDISON SENIOR RAIL ASSEMBLY INSTRUCTIONS
Mount End-Leg Cap and End Leg to Rail
Flip the rst rail of the run upside down onto a
soft surface. Attach an end cap to one end of
the rail segment using 4 (0000822) push rivets.
Next attach the end leg to the bottom of the rail
segment using 4 (0001140) screws. You will
repeat this step for the end-of-run rail segment
as well. Please note: a 90 degree bit is helpful
for this step.
Mount Mid-Leg Cap to Rail
If attaching another rail segment, attach a mid-leg cap
using 4 (0000822) push rivets on the other end of
the rail. Repeat this step for all middle rail segments,
adding two mid-leg caps to each mid-segment rail,
and one end-leg cap to each end-segment rail.
M6-1.0x12mm Low
Profile Cap Screw
(0001140)
Plastic Reusable
Push Rivet
(0000822)
Plastic Reusable
Push Rivet
(0000822)
1.
2.