WATSON SEVEN User manual

USER MANUAL
SEVEN
V.2.2 4/16 INS-SVN-USER

2 Seven Assembly | INS-Seven-USER | watsonfurniture.com
IMPORTANT SAFETY INFORMATION
THIS PRODUCT IS FOR COMMERCIAL USE ONLY.
Important information on Seven products can be found
under the following headings:
DANGER
To reduce the risk of electric shock, always unplug this
furnishing from the electrical outlet before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or
injury.
1. Unplug from outlet before putting on or taking o
parts.
2. Close supervision is necessary when this furnishing
is used by or near children, invalids, or disabled
persons.
3. Use this furnishing only for its intended use
as described in these instructions. Do not use
attachments not recommended by the manufacturer.
4. Never operate this furnishing if it has a damaged
cord or plug, or if it is not working properly.
5. Keep the cord away from heated surfaces
6. Do not use outdoors.
7. Risk of Electric Shock --- Connect this furnishing
to a properly grounded outlet only. See Grounding
Instructions, page 6.
8. The worksurface has a maximum weight capacity of
250 lbs., including worksurface weight.
9. Do not use the actuator system for lifting persons.
Do not stand or sit on the table while operating --- Risk
of Personal Injury.
10. Note that during construction applications in which
the actuator is to be fitted, there must be no possibility
of personal injury, for example the squeezing of fingers
or arms.
11. Do not overload the actuators --- this can cause
danger of personal injury and damage to the system.
12. Electrical connection between table segments shall
be disconnected prior to removal of a mechanical
connection.
13. Cords are not to be routed through or across to
another complete unit or worksurface. Channel is not
to be used for routing extension cords.
14. The combined length of a Seven furnishing
configured with a power raceway furnishing shall not
exceed 30 feet (9.1 m), or 12 segments of standard
power, 6 segments of heavy power.
15. This product is for use on a nominal 120-volt supply
circuit. When factory-equipped with NEMA 5-20P plug,
make sure that the product is connected to an outlet
having the same configuration as the plug. No adapter
should be used with this product.
16. To reduce the risk of electric shock, this furnishing
has a polarized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any
way.
17. Servicing of Double-Insulated Products In a double-
insulated product, two systems of insulation are
provided instead of grounding. No grounding means is
provided on a double-insulated product, nor is a means
for grounding to be added to the product. Servicing a
double-insulated product requires extreme care and
knowledge of the system, and is to be done only by
qualified service personnel. Replacement parts for a
double-insulated product must be identical to the parts
they replace. A double-insulated product is marked
with the words “DOUBLE INSULATION” or “DOUBLE
INSULATED.” The symbol (square within a square) is
also able to be marked on the product.
CAUTION
1. Assure free space for movement of application in
both directions to avoid blockade.
2. Do not use the system in environments other than
intended indoor use.
Please Read All Instructions Before Using

3 Seven User Guide | INS-SVN-USER | watsonfurniture.com
CARE + MAINTENANCE
We recommend that you not allow any of the following
reagents to remain in contact with the laminate:
• Hypochlorite bleach, except as described in
this manual
• Hydrogen peroxide solution
• Mineral acids, hydrochloric acid (i.e. Lime-A-Way™),
sulfuric or nitric acid
• Caustic solutions containing greater than 2% lye,
(i.e. Drano®)
• Sodium bisulfate, such as Sani-Flush®
• Potassium permanganate
• Berry juices
• Silver nitrate, in 1% concentration or greater
• Gentian violet
• Mild silver protein, such as 20% Argyrol
• Bluing
• Fabric dye, such as Tintex® or Rit®
• Alcohol containing 1% iodine in solution
Fabric Panels
Fabric may be cleaned with mild, water-free solvents or
water-based cleaning agents or foam. For tough stains,
we recommend Shout® wipes as an eective cleaner.
Storage
When not in use for an extended period of time,
always unplug this furnishing from the electrical
outlet and carefully stow the power cord to avoid
accidental damage.
WARNING
Always rinse laminate surfaces after cleaning. Cleaning
solutions may leave behind a residue that can be
reactivated by moisture from cups or drinks. Prolonged
exposure to cleaning residues can cause permanent
discoloration, scars, or stains in laminate surfaces.
CAUTION
For normal cleaning, vacuum panel fabric as needed,
using an upholstery attachment. Do not brush fabric or
use a vacuum attachment with a rotary brush. Brushing
may permanently damage the nap or change the
character of the fabric.
Surface & Case Laminate
To clean the surface, use mild soap or detergent
with a damp cloth or sponge. Dicult stains such as
coee or tea can be removed by using mild household
cleaner and baking soda; mixing to achieve a paste
consistency. Gently wash (approximately 15-20 strokes)
the aected area using a sti nylon bristle brush. Do not
scrub so as to scratch the surface finish. Avoid cleaners
with ammonia.
Marker Board Laminate
Wilsonart Marker Board Laminate can be cleaned using
a felt or multi-purpose board eraser. When additional
cleaning is required, a soft cloth dampened with warm
tap water and mild soaps, such as those used for hands
or dishes, is recommended. Remember to clean erasers
often by wiping to remove dry-erase marker residue.
Stubborn Stains
Stubborn stains that resist any of the mentioned
cleaning methods may require the use of undiluted
household bleach or nail polish remover. Use a cotton
ball saturated with bleach or nail polish remover
(acetone), gently rub the stain for up to two minutes.
Rinse thoroughly with warm water and wipe dry with
a soft cloth. This step may be repeated if the stain
appears to be going away and the color of the laminate
has not been aected.
Note — Scrubbing too hard or at length can damage
the surface finish.
If stubborn stains persist, Marker Board Laminate can
be cleaned with spray-type glass cleaners, such as
Windex®.
Do not use cleansers that contain abrasives, acids or
alkalis; they will damage the surface. Remove stubborn
stains with a 2-minute exposure to hypochlorite bleach,
such as Clorox®, followed by a clean water rinse.

4 Seven User Guide | INS-SVN-USER | watsonfurniture.com
HEIGHT ADJUSTMENT
WORKSTATION TIPS
Switch Operation
The Seven Inset and Undermount Height-
Adjustment Switches have two buttons for
user operation.
Inset Switch Undermount Switch Wellness Switch
Ensure all user power cords are long enough to reach
from outlets to worksurface in the highest adjustment
setting. Do not subject cords to any strain while
adjustment of the surface is taking place.
TECHNICAL PRODUCT SPECIFICATIONS
Range of Adjustment Electric — 28-46”
Glide Adjustment ½"
Max. Weight Capacity 250lbs*
Wire Management
Included
Ye s
Controller Up/Down
Decibel Rating 50db(A) in
typical applications
Volts 120v AC
Frequency & Phase 60 Hz, Single Phase
Amps 2 Leg — 5.0A max.
3 Leg — 10.0A max.
Watts 2 Leg — 216 W max.
3 Leg — 300 W max.
Standby 0.1W
Adjustability Speed 1.6"/sec
Duty Cycle 10%
* Includes worksurface weight (≈5 lbs/ft)
Note — Rectangular tops weigh between 47-80 lbs; a
72”x29” top weighs 71 lbs.
Always check for proper operating clearance before
placing any item on, above or below the worksurface.
To reach the desired height, press and hold either the Up or Down
arrow. As a safety feature, the users must continuously hold down
the arrow button in order for the table to move.

5 Seven User Guide | INS-SVN-USER | watsonfurniture.com
USING SEVEN POWER AND DATA
Data Cable Clips
Insert for Data Jumpers
Free Space for Wire Routing
Power Block and Outlets
The Seven Raceway unit features a modular power
distribution 8-wire, four circuit manufactured wiring
harness system. Seven modular power distribution
is based on a power raceway furnishing consisting of
power blocks, preconfigured outlets, jumper cables
between power blocks, and power feed for hardwire
connection to building power supply.
Each raceway segment consists of one power raceway
furnishing with either 4 or 8 outlets per user. They are
rigidly mounted within a raceway which allows access
from above via phenolic lids and under via cable
openings. Communication and data cabling can be
routed inside the raceway via the included plastic clips
to support a technology rich environment. They are
facilitated with telecom plates for data jumpers located
in the power raceway furnishing.

6 Seven User Guide | INS-SVN-USER | watsonfurniture.com
WIRING SCHEMATIC
BLACK
WHITE/BLACK WHITE/RED
GREEN OR BARE GREEN/YELLOW
GREEN/YELLOW 2+2
BLUE 2+2BLUE
PINKBLACK
2+2
CIR. 1
DUPLEX
3+1 ONLY 2+2 ONLY
CIR. 4
DUPLEX
CIR. 3
DUPLEX
CIR. 3
DUPLEX
BLACK
WHITE/BLACK WHITE/RED
GREEN OR BARE GREEN/YELLOW
GREEN/YELLOW 2+2
BLUE 2+2
BLUE
PINK
2+2
CIR. 1
DUPLEX
CIR. 2
DUPLEX
3+1 ONLY 2+2 ONLY
CIR. 4
DUPLEX
CIR. 3
DUPLEX
CIR. 3
DUPLEX
WARNING: RISK OF FIRE OR ELECTRIC SHOCK. THIS OFFICE FURNISHING SYSTEM MAY BE CONNECTED TO MORE THAN ONE SOURCE
OF SUPPLY. ALL SOURCES MUST BE DISCONNECTED PRIOR TO ANY SERVICING. NO SINGLE CIRCUIT MAY BE POWERED BY MORE THAN
ONE SOURCE.
120 / 240V 1 ph
FOR 2+2 USE CIRCUITS 1, 3 , 4 ONLY
FOR 3+1 USE CIRCUITS 1, 3, 4 ONLY
CIRCUIT 2 CAN NOT BE UTILIZED
WITH 120/240V
120 / 208V 3 ph
FOR 2+2 USE CIRCUITS 1, 2, 3 , 4 ONLY
FOR 3+1 USE CIRCUITS 1, 2, 3, 4 ONLY
MAX 20AMPS PER CIRCUIT
MAXIMUM SEGMENTS CONNECTED:
12 STANDARD POWER
6 HEAVY POWER
MAX 20AMPS PER CIRCUIT
MAXIMUM SEGMENTS CONNECTED:
12 STANDARD POWER
6 HEAVY POWER

26246 Twelve Trees Lane NW, Poulsbo, Washington 98370
800.426.1202 watsonfurniture.com [email protected]
TROUBLESHOOTING
If the desk does not move up or down:
1Connect a lamp, or similar object, to the main power supply to
verify there is adequate voltage.
2Check all accessible cable connections and verify there is no
visible damage to cables, controls, control boxes or legs.
3If all systems appear intact, unplug the desk for five minutes then
plug the desk back in and perform a Reset. If the problem persists,
contact your facility administrator.
If the desk stops and will only retract, check the following:
1Verify that the desk is fully extended. When the desk has
reached its uppermost position it can only run downward.
2Remove some of the load and try again.
If the desk will only adjust downward even though the desk
is not overloaded, perform a Reset.
If the desk does not move all the way up and repeatedly
stops at the same position, perform a Reset.
If the desk collides with an object, follow these steps:
1Adjust the desk up or down, away from the obstruction.
2Perform a Reset.
If the power cable disengages from the control box, check
the following:
1Confirm that the control box is properly installed.
2If the power cable is not plugged into the control box, reinstall
the control box using these steps:
a. Remove the worksurface from the rail.
b. Remove the control box.
c. Plug in the power cable to the control box and zip tie the
cable to the strain relief mounting point using the supplied
push-in rivet (see diagram at right). This important step
ensures the cable remains plugged in while the desk travels
up and down.
d. Place the control box in the rail between the two access
cutouts. Orient the box in such a way that the box geometry
matches the cutout geometry.
RESET
Push the down button to completely lower the console. After
reaching lowest setting, re-engage the down button and hold for
5 seconds.
SAVE THESE INSTRUCTIONS
CONTROL
BOX INSTALLATION
Loop power cable into the small
arcing groove and press in. This
provides strain relief for the
power cord so it does not come
disengaged during use.
Underside Shown