WATSON Edison Junior Rail User manual

ASSEMBLY
Edison Junior Rail
V.21.00 05/2021 360.394.1300 watsonfurniture.com

WARNING - Risk of Fire or Electric Shock. It is possible for this ofce furnishing system to be connected to more than one source of
supply. Disconnect all sources prior to any servicing. A single circuit shall not be powered by more than one source.
WARNING - Electrical connection between rail segments shall be disconnected prior to removal of a mechanical connection.
WARNING - The system may be supplied by a three phase power system with four individual circuits rated at 20 amps/120 volts max-
imum, or as permitted by local code.
WARNING - No more than 12 duplex receptacles shall be supplied by one circuit. (12 segments Two Duplex, 6 segments Four Duplex)
WARNING - For commercial use only.
NOTE - Installation must be in accordance with the National Electrical Code and local codes. Electrically interconnected tables need
to be mechanically connected.
WARNINGS
It is recommended to perform as much of the rail assembly upside-down, keeping in mind how many installers are available to ip
the run right-side up once assembled.
General Rail Assembly Notes
If 1 - 2 installers: ip the rst rail segment upside down and
complete steps 1 & 2. Then ip the rail right side up and continue
with instructions, adding one segment at a time for step 3.
If 3+ installers: complete steps 1-4 with the rail ipped upside
down. Once complete, ip right side up. The length of run will
determine how many installers are needed to perform the ip.

3 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
Edison Junior Rail Components
End Leg
End-Leg & Mid-Leg
Caps
Mid Leg
Jumper
Rail Side Panel
Rail Segment
Gallery End Panel
Gallery End Panel
Rail Mount
Gallery End Panel
Joiner Panel
Power Harness
Floor Anchor for Stand-
Alone Rail Segments
Power Harness
Housing
Spline Rod
Power Infeed
Cable Basket
*Optional

4 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
Hardware
Screw SMS #10 x
3/4 Truss Head PH,
Black (122875)
Tools
Screw M6-1.00 x
12MM BHSCS, Black
(125285)
8-32x1/4” Screw,
Steel (121538)
Screw M6 x 50MM
Partial Socket, Black
(0003010)
Floor Anchor Screw
(48013)
Phillips Drill/Driver
Bit
2mm Hex Drill/
Driver Bit
3mm Hex Drill/
Driver Bit
Additional tools such as a 90 Degree Bit and an 18” Extension are helpful for
some steps
*No torque or ball bits should be used
Electric Drill
Screw M6 x 30MM
BHSCS, Black
(0002086)
18-8 Lock Washer
#8 .34” OD
(121406)
Screw Thread-Cutting
M4 x 8MM FH PH, Zinc
(0003016)
Clip 5/8” Conduit,
Black (391001)
Coupler I Connect
(053714)
M6 - 1.00 X 12MM
BHSCS (125290)
*Only included if
customer specified the
optional Cable Basket

5 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
Install Wire Management Clips
Flip all rail segments upside down onto a soft surface.
Attach the wire management clips to the bottom of
the rail using one thread cutting screw per clip (clip
quantity depends on segment size).
Mount End Leg to Rail
Start with the rst rail of the run, and slide the end leg
internal to the rail. Drive three screws from the bottom
and one on each side.
1.
2.
8-32x1/4” Screw,
Steel (121538)
Screw M6-1.00 x
12MM BHSCS, Black
(125285)

6 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
Mount End Cap to Rail
Slide the end cap on from below to clear the end leg
fastener. Screw on the end cap from both sides with
(2) screws per side. Repeat steps 2 - 3 for the end-of
run rail segment.
Mount Mid Leg Caps to the Rail
If attaching another rail segment, at the other end of
the rail, attached a mid leg cap using (2) screws per
side. Repeat this step for all middle rail segments,
adding two caps to each mid-segment rail, and one
end cap to each end-segment rail.
3.
4.
Screw Thread-Cutting
M4 x 8MM FH PH, Zinc
(0003016)
Screw Thread-Cutting
M4 x 8MM FH PH, Zinc
(0003016)

7 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
Connecting Rail Segments
After installing the mid leg caps, slide the rails onto
the mid leg assembly. The openings in the caps at the
end of each rail segment should t snuggly around the
mid leg assembly brackets. The below example shows
two end rail segments connected with one mid leg.
Screw Mid Leg Onto Rails
Secure the mid leg to the rails using (6) screws on
each side. Three screws are driven from the underside
of the rail, and three from the underside of the rail
interior for each side of the leg, as shown. The bottom
plate of the leg sits internal to the bottom plate of the
rail.
5.
6.
Screw M6-1.00 x
12MM BHSCS, Black
(125285)

8 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
One-Piece Panels: Attach Rail Mount
Screw the rail mount to the panel using (4) screws, continue to step 11.
Two-Piece Panels: Join Panels Together
In the case of a two-piece Gallery End Panel, slide the
spline rod into one screen, and then push the second
screen onto the rod to secure together.
7.
8.
Screw M6 x 30MM
BHSCS, Black
(0002086)
If the customer ordered Gallery End Panels, assembly will take place at this step in the process. If no Gallery End Panels were
ordered, continue to Step 13.
Optional Gallery End Panel Assembly

9 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
Two-Piece Panels: Attach Joiner Panel
Screw the joiner panel to the two main panels using
(8) screws.
Two-Piece Panels: Attach Rail Mount
Screw the rail mount to the joiner panel using (4)
screws, the top of the rail mount should come to a
height of 27”.
9.
10.
Screw SMS #10 x
3/4 Truss Head PH,
Black (122875)
Screw M6 x 50MM
Partial Socket, Black
(0003010)

10 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
Slide Rail onto Rail Bracket
Prop the screen against a wall to remain in standing
position. Slide the rail onto the bracket. The top plates
of the rail and the screen bracket should be on the
same plane. The bottom screen bracket plate should
be inserted above the rail bottom plate.
Mount Rail to Screen
Drive (3) M6 screws up from the bottom of the rail.
Screw in (2) thread cutting screws from each side of
the rail bracket to secure the rail in place.
11.
12.
Screw M6-1.00 x
12MM BHSCS, Black
(125285)
Screw Thread-Cutting
M4 x 8MM FH PH, Zinc
(0003016)

11 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
Install Jumpers and Power Harness
Align power harness outlets with cutouts in the rail segment. Feed the infeed through the cutout
in the bottom of the appropriate rail segment and connect it to the power harness. Next feed the
jumper through the mid leg and connect each end to each power harness. Jumpers only connect
in one orientation: arrows on jumper and harness will align to indicate proper connection. Ensure
the jumper plastic clips are engaging the harness lip to prevent disconnection. The mid leg must
be straight at the time of routing the jumper through.
13.

12 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
Secure Power Harness & Infeed
Mount the power harness housing using (4) screws
(a.). Secure the ground wire to the side of the rail
using the star washer and screw (b.). Next secure the
infeed with the strain relief bracket where the infeed
exits the rail (c.).
14.
a.
b.
c.
8-32x1/4” Screw,
Steel (121538)
18-8 Lock Washer
#8 .34” OD
(121406)
8-32x1/4” Screw,
Steel (121538)

13 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
Attach Rail Mounts
Attach mounting brackets to the rail mount plates on
the the bottom rail rung with (2) button head screws
per bracket (4 total).
15.
Optional Cable Basket
M6 - 1.00 X 12MM
BHSCS (125290)

14 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
Secure Cable Basket
Position the Cable Basket onto the mounting brackets
and attach with (2) button head screws per bracket (4
total).
16.
M6 - 1.00 X 12MM
BHSCS (125290)

15 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
Attach Side Panels
[If installing rail accessories, assembly will take place at this step in the process,
before attaching side panels. Refer to separate Edison Rail Accessories Assembly
Instruction document.] Holding the bottom handle of the side panel, align the
cutouts for the power with the plug faces in the rail and push against the rail.
Magnets will catch and secure the panel to the rail.
Bending the Rail
Once the run is assembled, and power/data
is installed, bend the rails to the desired
angles. The mid legs can bend to 90
degrees in either direction. The
mid leg feet will pivot as the rail
segments bend and should
always remain perpendicular
to the mid leg assembly.
17.
18.

16 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
Leveling the Rail
Loosen the two set screws on each leg, and the foot will spin
freely and telescope in and out, raising and lowering that
section of rail. When the desired height is reached, re-tighten
the screws. PLEASE NOTE: the leg must always be re-tightened
so the foot sits perpendicularly to the rail for the end legs, and
perpendicular to the mid leg assembly for the mid feet.
19.
Floor Mount (for single rail segments)
In the case of a stand alone rail segment, the rail
assembly must be mounted to the oor using the
supplied oor anchor bracket and (4) oor anchor
screws. Repeat with other End-Leg.
20.
Floor Anchor Screw
(48013)

17 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS
Wiring Schematic
120 / 240V 1 ph
For 2+2 Use Circuits 1, 3 , 4
ONLY
For 3+1 Use Circuits 1, 3, 4
ONLY
circuit 2 can not be
utilized with 120/240V
120 / 208V 3 ph
For 2+2 Use Circuits 1, 2, 3 , 4 ONLY
For 3+1 Use Circuits 1, 2, 3, 4 ONLY
BLACK WHITE/BLACK WHITE/RED
GREEN OR BARE GREEN/YELLOW
GREEN/YELLOW (2+2)
BLUE (2+2)BLUE
PINKBLACK
(2+2)
CIR. 1
DUPLEX
3+1
ONLY
2+2
ONLY
CIR. 4
DUPLEX
CIR. 3
DUPLEX
CIR. 3
DUPLEX
BLACK
WHITE/BLACK WHITE/RED
GREEN OR BARE GREEN/YELLOW
GREEN/YELLOW (2+2)
BLUE (2+2)
BLUE
PINK
(2+2)
CIR. 1
DUPLEX
CIR. 2
DUPLEX
3+1
ONLY
2+2
ONLY
CIR. 4
DUPLEX
CIR. 3
DUPLEX
CIR. 3
DUPLEX
WARNING: Risk of fire or electric shock. This office furnishing system may be connected to more than one source of supply. All
sources must be disconnected prior to any servicing. No single circuit may be powered by more than one source.