WATSON Haven Social Tables User manual

ASSEMBLY
360.394.1300 watsonfurniture.com
V.21.0 11/2021
Haven Social Tables

2 HAVEN SOCIAL TABLES ASSEMBLY INSTRUCTIONS
Haven Social Table Components - Four Leg
Surfaces (Four Leg Shown)
Support Rails
(only included on certain size tables)
Optional: Foot Bar Components Optional: Cable Tray
Coat Hooks
(only included on 36”H and 42”H tables)
Legs

3 HAVEN SOCIAL TABLES ASSEMBLY INSTRUCTIONS
Haven Social Table Components - Six and Eight Leg
Surfaces (Six Leg Shown)
Support Tubes
Bridge Legs
Optional: Foot Bar Components
Optional: Cable Tray
Coat Hooks
(only included on 36”H and 42”H tables)
Cable Tray Bracket
(only needed for certain size tables)

4 HAVEN SOCIAL TABLES ASSEMBLY INSTRUCTIONS
Hardware
#10 X 1” Torx Head
Screw (0002147)
M6 - 1.0 X 20mm
Flat Head Screw
(0002150)
Tools
Electric Drill Phillips Bit
10-32 Plastic Head
Thumb Screw
(0000638)
For optional Cable
Tray only
M6 - 1.0 X 6mm
Cup Point Set Screw
(0002246)
For optional Foot Bar
only
Foot Bar Connector
(0002146)
1/4 - 20 X 3.5” Bolt Tite-Joint
Connector (490006)
For 6-Leg and 8-Leg tables only
T25 Torx Bit3mm Hex Bit 4mm Hex Bit
M6 - 1.0 X 12mm Screw
(125285)
For 6 and 8-Leg Tables
13mm Wrench

5 HAVEN SOCIAL TABLES ASSEMBLY INSTRUCTIONS
1. 4-Leg Tables: Attach Legs and Support Rails
Lay the worksurface upside down on a soft surface. Align each leg with the corresponding pilot holes in the surface
and secure with (8) screws each. If support rails are included, align each support rail to the pilot holes in the surface
and secure with (5) screws each. Note: Support rails may or may not be included depending on table size/shape.
Haven Social Tables are offered in 4-Leg (one-surface), 6-Leg (two-surface), and 8-Leg (three-surface) sizes. The 4-Leg tables are
assembled with different parts than the 6-Leg and 8-Leg tables, each with their own set of instructions. Please skip to page 8 for
the 6-Leg and 8-Leg instructions.
General Assembly Notes
2. 4-Leg Tables: Attach Coat Hooks (only included on 36”H and 42”H tables)
Align the holes on the hook with the square holes in the leg plates and secure the hook with (2) screws. Repeat for the
remaining legs.
#10 X 1” Torx Head
Screw (0002147)
#10 X 1” Torx Head
Screw (0002147)

6 HAVEN SOCIAL TABLES ASSEMBLY INSTRUCTIONS
3.
b.
4-Leg Tables: Attach Optional Foot Bar
Lay out the Foot Bar tubes for pre-assembly ensuring that all the holes in the tube are facing up. Insert a connector
(0002146) into each tube joint and align the centerline indicator with the edge of the tube. Drive (2) set screws
(0002246) per tube end to secure the connector in place. Repeat for remaining connections (b). Carefully lower the
assembled Foot Bar into place inside the legs of the table until the connector tabs line up with the holes in the legs. The
tabs should be facing up at this point. Drive one screw (0002150) per leg to afx the Foot Bar (b.).
a.
Centerline Indicator
M6 - 1.0 X 20mm
Flat Head Screw
(0002150)
M6 - 1.0 X 6mm
Cup Point Set Screw
(0002246)

7 HAVEN SOCIAL TABLES ASSEMBLY INSTRUCTIONS
4.
a.
4-Leg Tables: Attach Optional Cable Tray
Insert the Cable Tray tabs into the slots in the Support Rail (a.). Swing the Cable Tray up until the keyslots on the opposite
side of the Cable Tray line up with the holes in the Support Rail. Thread in (2) thumb screws to lock the tray in place (b.).
b.
10-32 Plastic Head Thumb
Screw (0000638)

8 HAVEN SOCIAL TABLES ASSEMBLY INSTRUCTIONS
1. 6 and 8-Leg Tables: Assemble Table Frame
Lay the bridge legs and support tubes upside down on a soft surface. Align each leg bracket with a support tube and slide
tube into bracket, aligning the pilot holes in the bracket with the holes in the support tube. Secure each support tube end
with (2) screws each.
M6 - 1.0 X 12mm Screw
(125285)
For 6 and 8-Leg Tables

9 HAVEN SOCIAL TABLES ASSEMBLY INSTRUCTIONS
2.
Centerline Indicator
M6 - 1.0 X 20mm
Flat Head Screw
(0002150)
M6 - 1.0 X 6mm
Cup Point Set Screw
(0002246)
6 and 8-Leg Tables: Attach Optional Foot Bar
Lay out the Foot Bar tubes for pre-assembly ensuring that all the holes in the tube are facing up. Insert a connector
(0002146) into each tube joint and align the centerline indicator with the edge of the tube. Drive (2) set screws
(0002246) per tube end to secure the connector in place. Repeat for remaining connections (b). Carefully lower the
assembled Foot Bar into place inside the legs of the table until the connector tabs line up with the holes in the legs. The
tabs should be facing up at this point. Drive one screw (0002150) per leg to afx the Foot Bar (b.).
b.
a.

10 HAVEN SOCIAL TABLES ASSEMBLY INSTRUCTIONS
3. 6 and 8-Leg Tables: Attach Surfaces Together
Flip the base over so it’s sitting upright. Place the surfaces offset on the base as shown to allow access to the tite joint
locations. Push the surfaces together making sure to align them depth-wise. Place tite joints into the corresponding
cutouts and tighten them to close the gap between the surfaces.

11 HAVEN SOCIAL TABLES ASSEMBLY INSTRUCTIONS
4. 6 and 8-Leg Tables: Attach Surface To Base
Align the worksurface pilot holes with the slots in the bridge legs and drive the appropriate number of woods screws.
Tip: get at least one hole aligned and loosely drive a screw in that hole before trying to align other holes.
#10 X 1” Torx Head
Screw (0002147)

12 HAVEN SOCIAL TABLES ASSEMBLY INSTRUCTIONS
5. 6 and 8-Leg Tables: Attach Coat Hooks (only included on 36”H and 42”H tables)
Align the holes on the hook with the square holes in the leg plates and secure the hook with (2) screws. Repeat for the
remaining legs.
#10 X 1” Torx Head
Screw (0002147)

13 HAVEN SOCIAL TABLES ASSEMBLY INSTRUCTIONS
6. 6 and 8-Leg Tables: Attach Optional Cable Tray
Depending on the table depth, the Cable Trays may come with brackets that need to be attached to the table (see
next page). If not, the Cable Tray tabs will be inserted into slots in the Support Rail. Swing the Cable Tray up until the
keyslots on the opposite side of the Cable Tray line up with the holes in the Support Rail or bracket. Thread in (2)
thumb screws to lock the tray in place.
a.
10-32 Plastic Head Thumb
Screw (0000638)
b.

14 HAVEN SOCIAL TABLES ASSEMBLY INSTRUCTIONS
7. 6 and 8-Leg Tables: Attach Cable Tray Bracket
Attach the cable tray bracket with (2) screws per bracket to the pilot holes in the surface, as shown below. Attach cable
tray using the brackets in the same manner as step 6.
DETAIL A
SCALE 0.1 : 1
A