WB Mfg ELO Desk User manual

1
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
V030119 subject to change.
ELO® Desk/Table
Assembly Instructions
Instructions are based on the ELO® Adapt Desk but can be used for any ELO® Desk or Table.
Before you begin, please make sure all parts and proper quantities are included. (See Part Identier Key page) Any parts damaged during shipment must be
reported within 24 hours of receipt. To report information regarding damages or if you have any questions, please call 800.242.2303.
Step 2
Tools Required
• Screw gun
• 4mm Hex bit
• Drill bit extension
• Phillips head screwdriver
Step 1:
• Place top face down on protected at surface so
threaded inserts are facing up.
Step 2:
• Align leg(see leg options below) with threaded inserts.
• Connect leg to desktop with the ¼-20x15mm joint
connector bolt. Use six bolts for each leg.
• Use a screw gun, 4mm Hex bit and a drill bit extension to
tighten the joint connector bolts to the desktop.
• Repeat this for the rest of the legs.
Step 3:
• Adjust legs to desired height then ip over.
Step 4:
• If your table requires a support bar/s, align the bar/s with
the pre-drilled pilot holes. Use #8x¾” screws to fasten
down the support bar to the desktop.
ELO (-ADJ or -EJA)
1.25” Square Legs
ELR (-ADJ or EJA)
2” Curved Round Legs
ELS (-ADJ, EJA or MJA)
2” Straight Round Legs
ELP (-ADJ or EJA)
2” Straight Round Pin Legs
ELO® Leg Options
#8 Screws
Support bar
Worksurface
(Bottom side)

2
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Assembly Instructions
for Optional Accessories
ELO® Desk/Table
with Dual Wheel Locking Casters
or 2.5” Grand Hank Glides
Step 1:
• Remove Nylon glide from leg by rotating counterclockwise until
glide is free.
Step 2:
• Place stem of optional footing into the hole on the leg. Rotate
clockwise until fully inserted into leg.
• Casters are NOT to be used as a leveling device.
Step 3:
• Tighten with a 14mm open-ended wrench. (only with the dual
wheel caster.)
Step 4:
• Repeat for each caster or Grand Hank glide.
Step 1:
• Place top face down on protected at surface.
Step 2:
• Align tabs of the backpack hook with the metal inserts.
Step 3:
• Use ¼-20x15mm joint connector bolts to fasten both of the tabs
of the backpack hook to the top.
Instructions are based on the ELO® Adapt Desk but can be used for any ELO® Desk or Table.
ELO® Desk/Table
with Backpack Hook
Tools Required
• 14mm open-ended wrench
Tools Required
• Screw gun
• 4mm Hex bit
Before you begin, please make sure all parts and proper quantities are included. (See Part Identier Key page) Any parts damaged during shipment must be
reported within 24 hours of receipt. To report information regarding damages or if you have any questions, please call 800.242.2303.

3
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Part Identifier Key
ELO® Desk/Table
Adjustable Legs
Model #
Smooth Silver
Sku #
Black
Sku# Descripon Height"
ELO -ADJ 0400570-G4 0400570 ELO® 1.25" Square Adj. Leg 24.75 - 29.75
ELR -ADJ 04066649-G4 04066649 ELO® 2" Curved Round Adj. Leg 25 - 30
ELS -ADJ 04066821-G4 04066821 ELO® 2" Straight Round Adj. Leg 27 - 40
ELP -ADJ 04066829-G4 N/A ELO® 2" Straight Round Pin Adj. Leg 25 - 39
ELO -ADJ/EJA ELR -ADJ/EJA
Jr. Adjustable Legs
Model #
Smooth Silver
Sku #
Black
Sku# Descripon Height"
ELO -EJA 0400755-G4 0400755 ELO® 1.25" Square Jr. Adj. Leg 20 - 25
ELR -EJA 04066650-G4 04066650 ELO® 2" Curved Round Jr. Adj. Leg 21 - 26
ELS -EJA 04066652-G4 04066652 ELO® 2" Straight Round Jr. Adj. Leg 20 - 33
ELP -EJA 04066785-G4 N/A ELO® 2" Straight Round Pin Jr. Adj. Leg 19 - 29
ELS -ADJ/EJA ELP -ADJ/EJA
Mini Adjustable Leg
Model #
Smooth Silver
Sku #
Black
Sku# Descripon Height"
ELS -MJA 04067425-G4 N/A ELS® 2" Straight Round Mini Adj. Leg 10.75 - 17.75
ELS -ADJ/MJA
Part # Description Qty.
040164 1⁄ Dia. Grand Hank glides, ⁄-16 x 1” 1 per leg*
33021BK Dual wheel casters w/brake 1 per leg*
04067195 Soft tread casters 1 per leg
04009308-X1 (black)
04009308-G4 (smooth silver)
Backpack hook
(Needs (2) ¼”-20x15mm Joint Connector bolts) 1
04009023 ¼”-20x15mm joint connector bolts
(Used to fasten leg to top & for Backpack hook)
• 6 per leg*
• 2 per backpack hook
04009377 (42”)
04066738 (50”)
0407127 (60”)
0407118 (72”)
Stretcher bar 1 to 2 depending on
model
0404248 #8x¾” screws
(Used to fasten stretcher bar to top) 10
*A typical desk/table has 4 legs - see next page for a list of desks and tables that require a support bar/s or 3, 5 or 6 legs.

4
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Part Identifier Key
ELO® Desk/Table
Desks # of Legs
ELO® Connect 4 3
ELO® Diamond 3
ELO® Mini Diamond 3
ELO® Mini Nimubs 3
ELO® Pyramid 3
Shaped Tables # of Legs
ELO® Benton 5
ELO® Delta 5
ELO® Double Delta 6
ELO® Flower 6
ELO® Horseshoe (240) 5
ELO® Horseshoe (244) 5
ELO® Horseshoe (241) 5
ELO® Manta 3
ELO® Nimbus 3
ELO® Tri- 6
Rectangle Tables # of Legs
# of
Support Bars
Up to 72” L 4 1
84” & 96” L 6 -
Court Tables # of Legs
# of
Support Bars
36”D X (60”L & 72”L) 4 1
36”D X 96”L 5 1
48”D x 96”L 6 1
42”D 5 1
48”D X (60”L, 72”L & 84”L) 5 1
48”D X 96”L 6 1
60” D 5 2