WB Mfg TORO User manual

1
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specications are subject to change. Product
images are for illustrative purposes only and may
dier from the actual product.
TORO Tables
Laminate/Phenolic/Stainless Steel & 1 Pc Butcherblock Tops
Step 1:
• Place the TORO top face down on a protected at surface.
Step 2:
• Place TORO frame down on top of the TORO top and align with
pre-drilled pilot holes.
• If assembling an Epoxy top, see Epoxy TORO Table Assembly
Instructions.
• If assembling a 2 piece Hardwood top, see Hardwood TORO
Table Assembly Instructions.
Step 3:
• Using a # S2 square bit, secure frame to table top with #10 x ¾”
square pan screws. One screw per tab.
Step 4:
• Locate TORO inserts. Remove M6 screws and #12 star washers
from the insert using a 4mm hex wrench.
Step 5:
• Place insert into TORO frame and once desired height is
attained, place #12 star washer and M6 screw through the hole
and tighten with a 4mm hex wrench. Repeat with the 2nd star
washer and M6 screw.
• Repeat Step 5 for the remaining inserts.
Step 6:
• With someone’s help, turn table upright.
V061020 subject to change.
Step 3
Shown with optional gussets
Step 4
Step 5
Tools Required
• 4mm Hex Wrench
• Screw Gun
• # S2 Square Bit
Assembly Instructions
Before you begin, please make sure all parts and proper quantities are included. (See Part Identier Key) Any parts damaged during shipment must be reported
within 24 hours of receipt. To report information regarding damages or if you have any questions, please call 800.242.2303.

2
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specications are subject to change. Product
images are for illustrative purposes only and may
dier from the actual product.
Part # Description Qty.
0408231 #10 x ¾” Square pan screws
(Used to attach frame to top)
10
(Included in Hardware Pack located in leg box. May
need less depending on size and work service)
Part Identifier Key
3” Heavy Duty Caster Hardware Pack (04066968) Used only with 2” adj. legs (-ALR)
Part # Description Qty.
04067460
04067064
¼” Star washers
M6 1x18 screws
(Used in leg insert to prevent bending of the leg insert)
4 per set
4 per set
(Included in Hardware Pack located in leg box as
standard. Discard if casters are not installed.)
3” Heavy Duty Caster Hardware Pack (0402020) Used only with 1.5” adj. legs (-ADJ)
04067460
0401259
¼” Star washers
M6 1x14 screws
(Used in leg insert to prevent bending of the leg insert)
4 per set
4 per set
(Included in Hardware Pack located in leg box as
standard. Discard if casters are not installed.)
22.25”-36.25”
2” Round Adjustable
-ALR
28.5"
2” Round Fixed
-FXR
28.5”
1.5” Square Fixed
-FX
22.5”-36.5”
1.5” Square Adjustable
-ADJ
TORO Leg Options
TORO Tables
Laminate/Phenolic/Stainless Steel & 1 Pc Butcherblock Tops

3
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specications are subject to change. Product
images are for illustrative purposes only and may
dier from the actual product.
22.25”-36.25”
2” Round Adjustable
-ALR
28.5"
2” Round Fixed
-FXR
28.5”
1.5” Square Fixed
-FX
22.5”-36.5”
1.5” Square Adjustable
-ADJ
TORO Leg Options
Step 1:
• Remove Nylon glide from leg by rotating counterclockwise until glide is free.
Step 2:
• Place stem of optional footing into the hole on the leg. Rotate clockwise
until fully inserted into leg.
• Casters are NOT to be used as a leveling device.
Step 3:
• Tighten with a 14mm open-ended wrench. (only with the Dual wheel soft
tread locking caster.)
Step 4:
• Repeat for each caster or glide.
Assembly Instructions
Before you begin, please make sure all parts and proper quantities are included. (See Part Identier Key) Any parts damaged during shipment must be reported
within 24 hours of receipt. To report information regarding damages or if you have any questions, please call 800.242.2303.
Part # Description Qty.
040164 1⁄ Dia. Grand Hank glide, ⁄-16 x 1” 1 per leg
04067920 1.5” Soft Touch glide 1 per leg
33056S 1.25” Steel glide 1 per leg
04067540 Dual wheel soft tread locking casters
(N/A on epoxy resin tops) 1 per leg
Part Identifier Key
Installing casters on tables with epoxy resin tops will void the Epoxy warranty.
Tools Required
• 14mm open-ended wrench
TORO Tables
w/ Casters, Glides & Leg Info.

4
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specications are subject to change. Product
images are for illustrative purposes only and may
dier from the actual product.
Part # Description Qty.
0400993 3” heavy duty locking casters 1 per leg
Part Identifier Key
3” Heavy Duty Caster Hardware Pack (04066968) Used only with 2” adj. legs (-ALR)
Part # Description Qty.
04067460
04067064
¼” Star washers
M6 1x18 screws
(Used in leg insert to prevent bending of the leg insert)
4 per set
4 per set
(Included in Hardware Pack located in leg box as
standard. Discard if casters are not installed.)
3” Heavy Duty Caster Hardware Pack (0402020) Used only with 1.5” adj. legs (-ADJ)
04067460
0401259
¼” Star washers
M6 1x14 screws
(Used in leg insert to prevent bending of the leg insert)
4 per set
4 per set
(Included in Hardware Pack located in leg box as
standard. Discard if casters are not installed.)
Step 1:
• Before placing caster in the bottom of the leg, lock the caster by pushing
down on the brake lever.
Step 2:
• Twist the stem of the caster into the hole on the bottom of the leg. Applying
thread locking adhesive can help prevent unexpected loosening of the
caster.
Step 3:
• Use ¾” wrench to tighten ¾”nut on stem of caster.
Step 4:
• If using adj. legs, insert star washer and M6 screw in hole closest to the
caster and tighten with 4mm hex wrench. DO NOT OVER TIGHTEN.
• If using a FIXED leg, you will NOT need to use a star washer and M6 screw.
Step 5:
• Repeat for remaining casters.
Step 4
Step 2
Step 1
Step 3
Tools Required
• ¾”Wrench
• 4mm Hex Wrench
• Thread Locking Adhesive (optional)
Installing casters on tables with
epoxy resin tops will void the
Epoxy warranty.
Casters are NOT to be used as a leveling device.
Assembly Instructions
Before you begin, please make sure all parts and proper quantities are included. (See Part Identier Key) Any parts damaged during shipment must be reported
within 24 hours of receipt. To report information regarding damages or if you have any questions, please call 800.242.2303.
TORO Tables
w/ Heavy Duty Casters