WB Mfg TORO User manual

wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
1
Assembly Instructions
V010322 Version subject to change
Step 1:
• Place the TORO frame face down on a protected flat
surface.
Step 2:
• Place TORO frame on top of the top and align with the
pre-drilled pilot holes.
Step 3:
• Using a #S2 square bit, secure frame to top with #10
x 3/4” square pan screws
Step 4:
• If assembling TORO Table with fixed legs, skip to Step
6.
• If assembling TORO Table with adjustable legs, locate
the adjustable insert to the legs.
• Remove M6 screws and #12 star washers from the leg
insert using a 4mm hex wrench.
Step 5:
• Place insert into TORO frame. Once desired height is
attained, place #12 star washer and M6 screw through
the hole and tighten with a 4mm hex wrench.
• Repeat with the second star washer and M6 screw.
• Repeat this step for the remaining leg inserts.
Step 6:
• Turn table to the upright position with the help of
another person.
Step 3
Step 4
Step 5
Before you begin, please make sure all parts and proper
quantities are included. (See Part Identifier Key) Any parts
damaged during shipment must be reported within 24 hours of
receipt. To report information regarding damages or if you have
any questions, please call 800.242.2303.
TORO Table
Laminate/Phenolic Top
Tools Required
• 4mm hex wrench
• Screw gun
• #S2 square bit

wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
2
Assembly Instructions
Step 4
Step 2
Step 2
Step 3
TORO Table
Laminate/Phenolic Top w/Heavy Duty Casters
Tools Required
• 1⁄” wrench
• 4mm hex wrench
Step 1:
• Remove nylon glide from leg by rotating counter-clockwise until
glide is free.
Step 2:
• Lock the caster by pushing down on the brake lever.
Step 3:
• Place stem of heavy duty caster into the hole in the bottom of the
leg. Rotate clockwise until fully inserted into leg.
Step 4:
• Use 1⁄” wrench to tighten ⁄” nut on stem of caster. Loctite on
casters will cause some resistance while tightening, please make
sure that casters are tightened all the way to prevent possible
damage to the stem of the caster.
Step 5:
• If using adj. legs, insert star washer and M6 screw in hole closest
to the caster and tighten with 4mm hex wrench. DO NOT OVER
TIGHTEN.
• If using a FIXED leg, you will NOT need to use a star washer and
M6 screw.
Step 6:
• Repeat for remaining casters.
Casters are NOT to be used as a leveling device.
TORO Table
Laminate/Phenolic Top w/Casters/Glides
Tools Required
• 4mm hex wrench
• Screw gun
• #S2 square bit
Step 1:
• Remove nylon glide from leg by rotating counter-clockwise until
glide is free.
Step 2:
• Place stem of optional footing into the hole in the bottom of the leg.
Rotate clockwise until fully inserted into leg.
Step 3:
• Tighten with a 14mm open-ended wrench. (Only for the dual wheel
soft tread locking caster.) Loctite on casters will cause some
resistance while tightening, please make sure that casters are
tightened all the way to prevent possible damage to the stem of the
caster.
Step 4:
• Repeat for remaining caster or glide.
Casters are NOT to be used as a leveling device.

wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
3
Assembly Instructions
Part Identifier Key
Part # Description Qty.
0408231 #10 x ⁄” square pan screws
(Used to attach leg plates and frame to top.)
10
(Included in hardware pack located in leg box.
May need less depending on size of top.)
0402020
3” Heavy Duty Caster Hardware Pack - Used only with 1.5” adj. legs (-ADJ) (Discard if casters are not installed.)
⁄” star washers (04067460) 4 per set
M6 1x14 screws (0401259)
(Used in leg insert to prevent bending of the leg insert) 4 per set
04066968
3” Heavy Duty Caster Hardware Pack - Used only with 2” adj. legs (-ALR) (Discard if casters are not installed.)
⁄” star washers (0404281) 4
M6x1x18 screws (0401259) 4
040164 2.5” Grand Hank glide,⁄”-16 x 1” 1 per leg
04067920 1.5” soft touch glide 1 per leg
NSL-33056S 1.25” steel glide 1 per leg
04067540 Dual wheel soft tread locking casters
(N/A on epoxy resin tops) 1 per leg