Whalen HO48CD-13AXV2 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2019-12-17 Rev. 0001-A
48” Computer Desk
Model # HO48CD-13AXV2
# HO48CD-13AXGRV2
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item
to the store where it was purchased. Please call our customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenfurniture.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Home Office Computer Desk
MODEL # HO48CD-13AX / HO48CD-13AXGR
MADE IN INDIA
M AX I M U M R E C O M M E N D E D W E I G H T L O AD S
THIS UNIT IS INTENDED FOR USE ONLY WITH THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 200 lb. (90.7 kg)
MAXIMUM LOAD 15 lb. (6.8 kg)

3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware
are present before beginning assembly.
A- Desk Top (Qty. 1) B- Left Leg (Qty. 1)
C- Right Leg (Qty. 1) D- Bottom Stretcher (Qty. 1)
(1) ¼-20 UNC-2A x 1 ¼ lg. Bolt (2) Lock Washer (3) Flat Washer
(Qty. 12+1 extra) (Qty. 8+1 extra) (Qty. 8+1 extra)
Hex Wrench (Qty. 2) Touch-up Pen (Qty. 1)
Tools required: Hex wrench (provided).

4
Assembly Instructions
NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled,
go back and fully tighten all bolts. This will make the assembly easier.
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Place the Desk Top (A) upside down on a level and protected surface.
3. Align and attach the Left Leg (B) to the side apron of the Desk Top (A) with the end dowels
fully inserted, using four 1-1/4” Bolts (1) with Lock Washers (2) and Flat Washers (3) from
inside through the drilled holes and securely screw into place.
4. Fasten the Bottom Stretcher (D) to the Left Leg (B) with two 1-1/4” Bolts (1).
5. Repeat the same procedure to attach the Right Leg (C) at the opposite end.
A
B
C
D
1
1
123
1
2
3
Flat Washer
(8 used in this step)
③
Lock Washer
(8 used in this step)
②
1/4” x 1-1/4” Bolt
(12 used in this step)
①

5
Assembly Instructions
6. Ask for assistance to stand the unit upright and position it at the desired location.
7. If necessary, adjust the pre-attached Floor Levelers on the bottom of the Legs (B and C) to
level the unit.
8. If you need to remove the drawer with the ball bearing slides from the unit, please pull the
drawer all the way out, then simultaneously push the plastic release lever of the ball bearing
slide up on one side and down on the other side, and then pull the drawer completely out.
NOTE: To place the drawer back, simply push the ball bearing cart all the way to the
end of the slides (in both sides), and align the slide runners on the drawer with the slide
tracks on the unit and push it carefully inside until it stops. If the drawer does not go in
smoothly, please take it out and repeat the step.
A