Whalen SFKCWMS User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2016-01-07 Rev. 2 Factory: FOCIDI
Santa Fe Kitchen Cart with Metal Shelves
Stock # SFKCWMS
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions and
parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASE
D
:
/
/

Stock # SFKCWMS
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 2 Factory: FOCIDI
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Santa Fe Kitchen Cart with Metal Shelves (SFKCWMS)
DATE OF MANUFACTURE: January 2016
MADE IN CHINA
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware part out of reach of children.
4. Please wait until all steps are completed before fully tightening bolts.
5. Make sure all bolts are tightly fastened before the unit is used.
MAXIMUM RECOMMENDED WEIGHT LOADS
GENERAL INFORMATION, TIPS
and
TRICKS
MAXIMUM LOAD 50 lb. (22.6 kg)
MAXIMUM LOAD 20 lb. (9.07 kg)
GENERAL INFORMATION, T
PLACE TV BEHIND THE STOPPER
FITS UP TO MOST 55"FLAT PANEL TVs
MAXIMUM LOAD 100 lb. (45.3 kg)
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH
FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND
WEIGHT LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL
TVS OR EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTRE OF
THE UNIT; THE BASE OF THE TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING
SURFACE OF THE UNIT WITHOUT OVER-HANGING THE EDGES. IMPROPERLY POSITIONED
FLAT PANEL TVS, OR FLAT PANEL TVS INCLUDING OTHER EQUIPMENT THAT EXCEED
RECOMMENDED SIZE AND WEIGHT LIMITS COULD FALL OFF OR BREAK THE UNIT,
CAUSING POS
SIBLE SERIOUS INJURY.

Stock # SFKCWMS
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 3 Factory: FOCIDI
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Section (1) B- Metal Shelf (2)
C- Left Front / Right Back Leg (2) D- Right Front / Left Back Leg (2) E- Side Handle (2)
F- Metal Bar (4) G- Locking Caster (2) H- Swivel Caster (2) I- Stop Rail (1)
(1) Ø1/4" x 5/8" Bolt (2) Ø1/4" x 1-1/4" Bolt (3) Ø1/4" x 1-3/4" Bolt
(16+1 extra) (8+1 extra) (4+1 extra)
(4) Lock Washer (5) Flat Washer (6) Drawer Handle with Bolts
(20+1 extra) (20+1 extra) (2)
4 mm Allen Wrench (1) Open Wrench (1) Touch-up Pen (1)
Tools required: Allen wrench and open wrench (provided), Phillips screwdriver (not provided).

Stock # SFKCWMS
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 4 Factory: FOCIDI
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Place the Top Section (A) on a level and protective surface.
3. Remove the utility drawers for the following steps. To remove the drawers, please pull the drawers all
the way out, then simultaneously push the plastic release lever of the ball bearing slides up on one side
and down on the other side, and then pull the drawers completely out.
4. Remove the bolts in Drawer Handles (6), and then use the bolts to attach the Handles to the outside of
the utility drawers by a Phillips screwdriver.
6
6
Drawer Handle with Bolts
(2 used in this step)
⑥
A

Stock # SFKCWMS
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 5 Factory: FOCIDI
Assembly Instructions
5. Align and attach four Legs (C and D) to the apron corners of the Top Section (A), using eight 1-1/4"
Bolts (2) with Lock Washers (4) and Flat Washers (5) from inside through the drilled holes on side
panels and screw into place. As shown.
A
D
C
D
C
A
C/D
5
4
2
Flat Washer
(8 used in this step)
⑤
Ø1/4" x 1-1/4" Bolt
(8 used in this step)
②
Lock Washer
(8 used in this step)
④

Stock # SFKCWMS
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 6 Factory: FOCIDI
Assembly Instructions
6. Attach the Side Handles (E) to the side panels of the Top Section (A) with four 1-3/4" Bolts (3) and
four Washers (4 and 5). As shown.
A
E
E
AE
345
Flat Washer
(4 used in this step)
⑤
Lock Washer
(4 used in this step)
④
Ø1/4" x 1-3/4" Bolt
(4 used in this step)
③

Stock # SFKCWMS
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 7 Factory: FOCIDI
Assembly Instructions
7. Fasten the Metal Bars (F) between the Legs (C and D) with eight 5/8" Bolts (1).
A
D
C
D
C
F
F
C/D
F1
Ø1/4" x 5/8" Bolt
(8 used in this step)
①

Stock # SFKCWMS
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 8 Factory: FOCIDI
Assembly Instructions
8. Securely screw the Casters (G and H) to the bottom of Legs (C and D) with the enclosed open wrench.
Make sure that two Locking Casters (G) are located at the same short end.
A
C
D
D
C
G
G
H
H

Stock # SFKCWMS
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 9 Factory: FOCIDI
Assembly Instructions
9. Flip the assembled unit at its back edges. Fit the Metal Shelves (B) between the Legs (C and D) making
sure the metal tabs overlap the threaded inserts on Legs (C and D). As shown.
10. Fasten the Metal Shelves (B) to the Legs (C and D) using the 5/8" Bolts (1) with the Washers (4 and 5)
through the metal tabs and screw into the legs.
11. Go back and tighten all bolts with the enclosed Allen wrench.
Ø1/4" x 5/8" Bolt
(8 used in this step)
①
Flat Washer
(8 used in this step)
⑤
Lock Washer
(8 used in this step)
④
C
D
C
D
B
B
C
D
D
C
B
B
C/D
B
5
4
1

Stock # SFKCWMS
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 10 Factory: FOCIDI
Assembly Instructions
12. Ask for assistance to stand the assembled unit upright.
13. Now, insert the removed drawers into the Top Section (A) to finish the assembly. To place the drawer
back, simply push the ball bearing cart all the way to the end of the slides (on both sides), and align the
slide runners on the drawer with the slides track on the unit. Push it carefully inside until it stops.
NOTE: If the drawer does not go in smoothly, please take it out and repeat the step.