Whalen PAL70ECON User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Furniture Mfg. Inc.
Factory No. 7-1564
Page # 1
PAL70ECON
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if you are
missing parts, do not return this item to the
Sam’s Wholesale Club
Please call our customer service number and have your
instructions and parts list ready to provide the model name,
part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 am - 4:30 pm Monday to Friday
MODEL No.: PAL70ECON
LOT No.:
DATE OF PURCHASE: / /

Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg. Inc.
Factory No. 7-1564
Page # 2
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen
Furniture purchase.
Should this product be defective in workmanship or materials
or fail under normal use, we will repair or replace it for up to 1
year from date of purchase. Every Whalen Furniture product is
designed to meet your highest expectations. We guarantee that
you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also
have other rights which vary from State to State.
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m. PST Monday to Friday
www.whalenfurniture.com
MANUFACTURER: WHALEN FURNITURE
CATALOG: Palermo 70” Entertainment Console (PALE70CON)
DATE OF MANUFACTURE: May, 2008
MADE IN CHINA
FITS UP TO MOST 70” FLAT PANEL TV’S
FITS UP TO MOST 35” CRT TV’S
MAXIMUM LOAD 180 LBS
MAXIMUM SHELF LOAD 30 LBS
Notes: CRT & Plasma TV’s with base support should be placed
squarely in the center of the stand with no overhanging on either side.
This unit is intended for use only with the products and
maximum weights indicated. Use with other products or products heavier than
the maximum weights indicated may result in instability causing possible injury.

Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg. Inc.
Factory No. 7-1564
Page # 3
Parts List
Please read completely through the instructions and verify that all
parts listed are present before beginning assembly.
A- TV Console (1)
B- Adjustable Wood Shelf (4) C- Raised Panel (2) D- Glass Panel (2)
(Pre-attached)
1- Shelf Pin w/Hole (16+1 extra) 2- 1/2” Screw (16+1 extra)
Touch Up Pen (1) Tipping Restraint Hardware Kit (2)
(Included in white plastic bag)
Tools Required: Phillips Screwdriver.

Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg. Inc.
Factory No. 7-1564
Page # 4
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and
required parts listed.
2. Position TV Console (A) on your desired room against wall to place
your TV on top when you finish assembly.
3. Open the middle doors and install Adjustable Wood Shelves (B) with
Shelf Pins (1) at your desired height. See detail #1.
Note: We recommend securing the shelf in place with supplied 1/2”
Wood Screws (2) for extra support of the unit.
Parts Provided Qty Tools Required
A –TV Console (1) Phillips Screwdriver
B –Adjustable Wood Shelf (4)
1 – Shelf Pin w/Hole (16)
2 –1/2” Wood Screw (16)

Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg. Inc.
Factory No. 7-1564
Page # 5
Assembly Instructions
Note: The middle doors of this unit are ship with Raised Panel (C). You
can keep the doors as they are or interchange with Glass Panel (D)
depending on your configuration.
4. To change configuration please open the middle doors and remove the
rubber liners on the back of the doors, remove the panels and replace
with the Glass. Then insert back all rubber liners. As shown in detail #2.
Parts Provided Qty Tools Required
C –Raised Panel (4) No Tool required
D –Glass Panel (4)
Pre-attached Rubber Liner

Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg. Inc.
Factory No. 7-1564
Page # 6
Assembly Instructions
5. In case of uneven floor, Floor Levelers are provided at the bottom of
console. To adjust unit in case of tilting or doors not being level,
simply tilt the unit back and adjust floor levelers by hand to correct
tilting and/or level Doors. As shown in detail #3.
TIPPING RESTRAINT HARDWARE
Note: We have included two Tipping Restraint Hardware bags for this Unit.
You must install this hardware to prevent accidents or injuries from falling
unit.
When properly installed, this restraint can provide protection against the
unexpected tipping of the Unit due to small tremors, bumps or climbing. We
strongly recommend mounting this hardware to a wall stud and your Unit.
Please carefully read the instructions printed on the bag.
Note: You must install the Tipping Restraint Hardware with the unit in
use to prevent any accidents or damage to the unit.
Tools Required: Phillips Screwdriver, Mallet, Power Drill, 3/8” Drill Bit.
A Touch-Up Pen has been provided to repair any small nicks or scratches
that may occur during assembly or shipping.
Your assembly should now be complete.
Thank you for your purchase.