Witura WT-1011RC IP 65 User manual

W
WT T- -1 10 01 11 1R RC C I IP P6 65 5
G
G
GS
S
SM
M
M
R
R
Re
e
em
m
mo
o
ot
t
te
e
e
C
C
Co
o
on
n
nt
t
tr
r
ro
o
ol
l
ll
l
le
e
er
r
r
A
A
An
n
nd
d
d
A
A
Al
l
la
a
ar
r
rm
m
m
S
S
Sy
y
ys
s
st
t
te
e
em
m
m
User Manual
&
Setting Instructions
W
W
WI
I
IT
T
TU
U
UR
R
R
A
A
A
C
C
CO
O
OR
R
R
P
P
PO
O
OR
R
R
A
A
AT
T
TI
I
IO
O
ON
N
N S
S
SD
D
DN
N
N
B
B
BH
H
HD
D
D

2
WT-1011RC IP65 GSM Remote Controller And Alarm S
y
stem
WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]
COPYRIGHT ©2010 WITURA CORPORATION SDN BHD
1) 1 pc IP65 Enclosure
2) 1 pc WT-1011RC Main Board with GSM Module mounted
3) 1 pc Battery Backup
4) 1 pc GSM Antenna
1. Introduction………………………………………………………………………………………………………………3
2. Features………………………………………………………………………………………………………………………3
3. Characteristic……………………………………………………………………………………………………………3
4. Installation Instructions………………………………………………………………………………………………6
5. WT-1011RC Programming Instructions ……………………………………………………………9
5.1 Programming the Administrator Numbers ……………………………………………………………………9
5.2 Access Control for Administrator……………………………………………………………………………………10
5.3 Programming the Guest List………………………………………………………………………………………..…10
5.4 Output Settings………………………………………………………………………………………………………………11
5.5 Input Settings…………………………………………………………………………………………………………………15
5.6 Alarm Settings………………………………………………………………………………………………………………20
5.7 Miscellaneous Settings…………………………………………………………………………………………………23
5.8 Connection of RS-232 Cable for Programming………………………………………………………………28
6. Technical Specifications……………………………………………………………………………….……………29
CONTENTS
PACKAGE CONTENTS

3
WT-1011RC IP65 GSM Remote Controller And Alarm S
y
stem
WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]
COPYRIGHT ©2010 WITURA CORPORATION SDN BHD
WITURA WT-1011RC GSM Remote Controller and Alarm System allow you to use your
mobile phone to monitor and control your business from any location. Its alarm facilities
provide a flexible way to distribute critical alarm information to any number of mobile
phone users.
WT-1011RC provides detailed alarm messages, secure alarm acceptance, full alarm
reporting and even remote process control. This allows user to rectify problems directly
via their mobile phone within minutes of the alarm occurring.
The WT-1011RC can monitor 2digital inputs. A SMS alarm message can be sent when
inputs triggered. The user can also interrogate the inputs through SMS messaging. The
WT-1011RC also has 2heavy-duty relay outputs can be used to switch on any
application like lamps, pumps, heaters etc. Output Relay 1 can be switched ON for a
preset time by calling its cell phone number, there is no call charges incurred when
dialing the unit as it will recognize an authorized telephone number calling it and reject
the call without answering. Output Relay 2 can be programmed to switch on for a pre-
determined length of time by sending the WT-1011RC a text command.
More flexible than pager based systems
Low set up and running costs
Faster response to alarms and process disturbances
Allows reduced manning levels
Increased freedom of movements for users
Reduces wasted traveling time responding to alarm events
Provides more detailed information
Easier monitoring of remote process
Allows full remote control
WT-1011RC is a versatile SMS alert device suited for most monitoring needs. It is
simple to use yet is packed with powerful functionalities to meet a wide ranging
industrial and commercial and residential applications
2. FEATURES
1. INTRODUCTION
3. CHARACTERISTIC

4
WT-1011RC IP65 GSM Remote Controller And Alarm S
y
stem
WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]
COPYRIGHT ©2010 WITURA CORPORATION SDN BHD
Housed in the weather and desk proof IP65 enclosure complete with internal industrial
modem, monitoring controller and flexible operating firmware. It is very easy to setup,
install and use.
Most equipment today does provide some form of alerting signal to interface to
monitoring devices from reporting of various malfunction or abnormalities. There are
various kinds of signal that the equipment can send out, most common of which are
opening or closure of one or more switch relay contact. UPS usually provide signals such
as incoming power fail, battery mode, battery level low, and switchover failure. An air
conditioner system may provide signals such as system on/off, compressor over
temperature, low gas pressure, etc.
Equipments to be monitored are connected to WT-1011RC using these alarm signaling
contacts. WT-1011RC keeps a constant watch over all the contacts. Whenever any
contact input changes status (either from a close to open or from an open state to close
state) it is captured by WT-1011RC. It will then process the input according to the
configuration provided by the user. The correct SMS messages will be sent to 8 mobile
phone users.
WT-1011RC is so fast in capturing the change of status of any signaling contacts that no
event will be missed out up to 2 inputs can be monitored directly. The flexibility of WT-
1011RC is in allowing remote query of input status using SMS.
To change contacting mobile phone number is also very easy. Authorize personal
remotely using SMS command to add, change or delete mobile phone number in WT-
1011RC.
WT-1011RC is a 2 way device. Besides monitoring inputs and act upon such inputs it
also allow mobile phone users to compose SMS messages to it. When WT-1011RC
receives any SMS, it will look its memory bank to see what it is supposed to do and
action according. No action SMS are ignored.
3.1 Standalone Operation
3.2 2 Digital Inputs
3.3 2 Digital Outputs

5
WT-1011RC IP65 GSM Remote Controller And Alarm S
y
stem
WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]
COPYRIGHT ©2010 WITURA CORPORATION SDN BHD
Relay 1 can turned on for a preset time by calling its number and Relay 2 can be
activated by text messages from mobile phone. Creating action messages are done with
the same ease as that of input monitoring.
Authorized groups can also query the status of an input or output. This is very useful
feature to determine the present status of an input or output. The enquirer need not
wait for an alarm to happen in order to receive the given I/O status.
Authorized users can send a SMS command to trigger on or off the digital output. Upon
receiving the command, WT-1011RC will perform the instructed action. After the on or
off action is done, it will send a reply to the querying mobile phone as an
acknowledgement.
WT-1011RC has a feature to allow user to remotely add, change or delete any mobile
phone numbers in WT-1011RC memory.
Re-assigning of operation personnel, a change of mobiles phone number is also
common. Rather than having to physically go to the installation site with a notebook
computer, the authorized personnel can perform the change from anywhere using
mobile phone. Where there are many installed sites, this feature saves time and afford.
Authorized mobile phone group can perform system check by sending a command to
WT-1011RC. If WT-1011RC is switched on or working normally, it will reply to the
querying number.
Integral to the design of WT-1011RC is a GSM 850/900/1800/1900Mhz Industrial
grade modem. Its capabilities and performance are highly optimized by the operating
firmware. Any change in the GSM signal and receiving conditions are detected quickly
and the software automatically takes care of signal errors
3.4 Querying Inputs And Outputs Status
3.5 Turning On / Off Device Remotely
3.6 Remote Editing Of Mobile Phone Numbers
3.7 System Check
3.8 GSM Modem

6
WT-1011RC IP65 GSM Remote Controller And Alarm S
y
stem
WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]
COPYRIGHT ©2010 WITURA CORPORATION SDN BHD
Besides running the necessary program to perform all the required functions, WT-
1011RC has diagnostic routines running alongside. Being a monitoring device, WT-
1011RC must have a very high operating reliability and stability. Every section of WT-
1011RC is monitoring each other. Should the modem fail to perform its required role,
the controller will interrogate and restart the modem.
For monitoring and remote control of equipments and machines that are able to provide
dry contract signals. 2 digital outputs with pulse functions extend control functions.
Suitable for door access control, On/Off equipment remotely, resetting of Routers,
Network switches etc. Some application examples are: -
Machines, Standby Power Generator, Electrical Panels, Pumps, Uninterruptable Power
Supplies, DC rectifier systems, Vending Machines, Fire Alarm Panels, Gas Monitoring
Systems, ATM Machines, Security Systems, Fishery, Cold rooms, HVAC systems, Door
Security, Network equipment and more.
IMPORTANT!
Please read through the instruction manual before you start to install and program the
device.
If you are unsure how to connect the device you wish to control please refer to a qualified
person.
Requirements:
- The WT-1011RC requires a 15 volt DC power supply capable of providing a minimum current of
1500mA, typical current consumption is 60mA
- A mobile phone SIM card with sufficient credit to send confirmation text messages when
programming the WT-1011RC unit. Note: The WT-1011RC identifies only 3V SIM card
3.9 Reliable Performance
3.10 Application
4. INSTALLATION INSTRUCTION

7
WT-1011RC IP65 GSM Remote Controller And Alarm S
y
stem
WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]
COPYRIGHT ©2010 WITURA CORPORATION SDN BHD
Installation:
Installing the SIM Card
Note: Installing the SIM Card. Please be sure the initial 4 digit PIN code of SIM card is disabled.
This can be done by placing it in an unlocked Mobile phone and first checking if the SIM requested
any PIN code. If this is the case the PIN code can be disabled using the security settings on the
phone.
Proceed as follows
1. Slide back the SIM door and lift it up
2. Slide the SIM card into the SIM door making sure that the clipped corner of the SIM card lines
up with the clipped corner of the SIM holder
3. Close the SIM door
4. Slide the SIM door to lock the SIM card in place
Power Up the Device
Connect a 15 volt DC power supply to terminal 3 & 4 ensuring positive is connected to terminal
3, switch on the power supply, the power LED will lit indicating power is present, the network
LED indicator will initially flash quickly, once logged onto the network it will flash more slowly
approximately every 3 to 4 seconds
Note: You should install the WT-1011RC in a place where there is GSM signal coming from the
operator you want to use. Check it with a phone before proceeding with the installation. If you
need to install the device in a place with little signal, you may consider using an external antenna
that we may supply as an option to be purchased separately with 5m cable.
Input 15VDC Power
here
Power Switch
Insert SIM card
here
Install Antenna
here
Connect to Battery
Back-u
p

8
WT-1011RC IP65 GSM Remote Controller And Alarm S
y
stem
WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]
COPYRIGHT ©2010 WITURA CORPORATION SDN BHD
Connection Details:
If you are unsure how to connect the device you wish to control please refer to a qualified
person.
Port Descriptions
1 +12 volts DC Output Audible Alarm Output
2 - 12 volts DC Output
3 +15 volts DC Input a 15 volts DC power that capable of
providing a current of 1.5 Amp
4 - 15 volts DC
5 +5 volts DC output Auxiliary 5 volts DC Output can be used to
trigger the inputs
6 Input 2 (IN2) A Standard +5V TTL signal will trigger this
Input
7 Ground (COM)
8 Input 1 (IN1) A Standard +5V TTL signal will trigger this
Input
9 Ground (COM)
10 NORMALLY OPEN (N.O) OUTPUT RELAY 2
(Can be Switched ON/OFF by SMS)
11 COMMON (COM)
12 NORMALLY CLOSED (N.C)
13 NORMALLY OPEN (N.O) OUTPUT RELAY 1
(Can be Switched ON by Caller ID)
14 COMMON (COM)
15 NORMALLY CLOSED (N.C)
1 2 3 4 6 7 8 9
NCNO C
15VDC
Power
Input
OUTPUT RELAY 2
10 11
12VDC
Audible
Alarm
Output
INPUT 2 INPUT 1
+-IN2
12 13 14 15
IN1 COM COM
NO C NC
OUTPUT RELAY 1
5
+
+5VDC
Output
+-

9
WT-1011RC IP65 GSM Remote Controller And Alarm S
y
stem
WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]
COPYRIGHT ©2010 WITURA CORPORATION SDN BHD
Example of Input & Output Connections
You can program the WT-1011RC via SMS commands using your phone. Any
programming command sent by SMS must be in CAPITAL letters. The fields between
square brackets are parameters; do NOT enter the square brackets. When you send a
command, you will receive the answer for the first time even if your GSM number is not
in the administrator list. This happens because the WT-1011RC recognizes any GSM
number as administrator and answers to it.
Attention: Please program the WT-1011RC unit systematically begin with programming the
administrator number.
The 8 administrator numbers can be programmed with a text command via SMS.
Text Command:
*TEL[N]#XXXXXXXXXX
N stands for administrator number 1 - 8
XXXXXXXXXX stands for the phone number you want to program as administrator.
1 2 3 4 6 7 8 9
NCNO C
15VDC
Power
Input
OUTPUT RELAY 2
10 11
INPUT 2 INPUT 1
+-IN2
12 13 14 15
IN1 COM COM
NO C NC
OUTPUT RELAY 1
LIGHT
110VAC
HEATER
110VAC
+5VDC
12VDC
Audible
Alarm
Output
+-
5
+
+5VDC
Output
5. WT-1011RC PROGRAMMING INSTRUCTIONS (via SMS Only)
5.1 Programming the Administrator Number

10
WT-1011RC IP65 GSM Remote Controller And Alarm S
y
stem
WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]
COPYRIGHT ©2010 WITURA CORPORATION SDN BHD
Please note that it is possible to program up to a maximum of 16 digits for a phone
number.
Example:
To program phone number 1111222233 as administrator into list number 1, you would
send the following SMS command to the unit.
*TEL1#1111222233
After sending the above command, the WT-1011RC will reply a message back to you
that the administrator number has been added.
Example of Returned Message:
#TEL1=1111222233
Note: It is advised that the owner should set the system to allow programming
access and remote control of Output Relay 1 for administrators only after
programming the Administrator numbers.
Sending SMS Command: *ANY?#1
Only the administrators in the list will have the authority to access the system and
remote control of Output Relay 1 by calling its number, any person outside the list in
this case will not have the authority to access the system and text command sent to the
system will be rejected.
To allow any person gain access to the system just send SMS Command: *ANY?#0
Note: Only Administrator number 1 and 2 may send this SMS command
The system allows the phone numbers in the Guest List as authorized user to operate
the output relays when calling its number. When the system received a phone call from
the Guest List, it will activate the output relays without answering the call therefore it is
free of charge. If it is not a registered user of the Guest List the call is rejected and the
output relays will never trigger. It is possible to program up to 100 phone numbers to be
authorized users in the Guest List of the unit and this can be done by sending the
following SMS to the unit.
5.2 Access Control For Administrators
5.3 Programming the Guest List