Wren 800 User manual

BASE UNIT
800 & 1000
Adjustable Corner
Assembly Guide
For Internal Use: FI.WR.INS.023_WKIN00105_BASE_Adj_Cnr_800 -1000_2Dr_Rev2.indd
800/1000 Magic
Corner Option
800/1000
1000 Cornerstone
Tray Option

BASE UNIT
800 & 1000
Adjustable Corner
Assembly Guide
For Internal Use: FI.WR.INS.023_WKIN00105_BASE_Adj_Cnr_800 -1000_2Dr_Rev2.indd
Page 1
(F) x12
Wooden Dowel
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x18
30mm
Screw
(J) x4
45mm
Screw Black
(L) x37
15mm
Screw
(N) x1
Door
Buer
(P) x5
Shelf Peg
Plastic
(M) x4
Cover
Cap
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Panel B
x2 End Panel
Back Panel
x1
Panel E
x2 Rail
Panel C
x1 Base Panel
Panel D
x1 Muntin
Shelf
x1
Legs
x5
Frontal
(Packed separately) x1
Panel A
x1 Back Panel
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
L Bracket
x4
Hinge Mounting Plate
x4 Inc Screws
Hinge
x2 Inc Screws
Space Plug
x2

BASE UNIT
800 & 1000
Adjustable Corner
Assembly Guide
For Internal Use: FI.WR.INS.023_WKIN00105_BASE_Adj_Cnr_800 -1000_2 Dr_Rev2.indd
Page 2
Step 1.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
Step 2.
Seat cam dowel (G)
into holes in
both end panels (B)
as shown.
Step 3.
Carcass Construction
Attach panels (C) &(E) to
panels (B), using cam dowel
(G) & cam lock (H) (in blue),
and also using dowels (F) (in
orange) in positions as shown.
Step 4.
Join panels (C)
& (E) to (B).
Insert cam lock (H).
Do NOT tighten until Step 6.
NB. All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
Seat (G)
cam dowel
into hole as
shown.
G G
GG F
F
F
F
G
G
G
G
F
F
F
F
F
F
F
F
B
B B
B
C
E
E
B
B
View from underside View from underside
H
G
G
H

BASE UNIT
800 & 1000
Adjustable Corner
Assembly Guide
For Internal Use: FI.WR.INS.023_WKIN00105_BASE_Adj_Cnr_800 -1000_2Dr_Rev2.indd
Page 3
B
B
C
D
E
JJ
J
Step 5.
Slide back panel (A) into
groove of end panels (B).
Once back panel (A) is in position, ensure
the panel is ush & square with bottom of
end panels (B).
Step 6.
Hand tighten all cam locks (H), this will
expand cam dowels (G) and tighten the
unit together.
Step 7.
Secure back panel (A) with 4 x 30mm screws (K) equally
spaced at the bottom of back panel (A) into base panel (C),
as shown.
Ensure you screw into the centre of base panel (C)
(9mm from the edge).
Step 8.
Join muntin panel (D) to unit, use pilot
holes to align muntin. Join muntin panel
(D), base panel (C) & rail panel (E) using
4 x 45mm screws (J) as shown.
Please refer to customer plan for left or
right hand orientation.
A
A
C
K
B
B
C
E
J

BASE UNIT
800 & 1000
Adjustable Corner
Assembly Guide
For Internal Use: FI.WR.INS.023_WKIN00105_BASE_Adj_Cnr_800 -1000_2 Dr_Rev2.indd
Page 4
Adjustable Corner Post Pack
Step 9.
Place packer (Z) ush with
the front edge of the cabinet
and up tight to the centre muntin.
Screw through from the cabinet
using 2 x 30mm screws (K) in the
top and 2 x 30mm screws (K) in
the bottom, locations shown.
Please refer to customer
plan for left or right hand
orientation.
X
Z
Y
Step 10.
Place panel (X) together with
the remaining packer (Z) ush
as shown and screw together
using 3x 30mm screws (K) equally
spaced as shown.
Please refer to customer
plan for left or right hand
orientation. Step 11.
Place panels (Y) & (X) together with
packer (Z) ush as shown and screw
together using 4 x 30mm (K) screws equally
space as shown. Please refer to customer plan
for left or right hand orientation.
Panel X x 1
Panel Y x 1
Packer Z x 2

BASE UNIT
800 & 1000
Adjustable Corner
Assembly Guide
For Internal Use: FI.WR.INS.023_WKIN00105_BASE_Adj_Cnr_800 -1000_2Dr_Rev2.indd
Page 5
Step 13.
Secure blanking panel with 9 x 15mm screws (L),
evenly spaced, as shown. Ensure you screw in
the centre of panels (9mm from edge).
Step 12.
Corner Blanking Panel
Measure and cut blanking
panel to required width.

BASE UNIT
800 & 1000
Adjustable Corner
Assembly Guide
For Internal Use: FI.WR.INS.023_WKIN00105_BASE_Adj_Cnr_800 -1000_2 Dr_Rev2.indd
Page 6
Step 14.
Secure each of the
legs into place with
2 x 15mm screws (L).
Step 16.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning carcass upright. Once in situ level accordingly.
Ensure legs are
rotated as shown
so that part of it is
supporting the end
panels (B).
Front legs should
have at edge to the
front.
Front
Leg position diagram
Front
C
C
B
L
L
B
Step 15.
Lightly hit centre peg of
leg base with hammer
until ush.
C
C
B
B

BASE UNIT
800 & 1000
Adjustable Corner
Assembly Guide
For Internal Use: FI.WR.INS.023_WKIN00105_BASE_Adj_Cnr_800 -1000_2Dr_Rev2.indd
Page 7
Carousel Tray
Please refer to separate instructions
included with your carousel tray.
The middle shelf should be discarded
when using the carousel tray.
1000 Carousel

BASE UNIT
800 & 1000
Adjustable Corner
Assembly Guide
For Internal Use: FI.WR.INS.023_WKIN00105_BASE_Adj_Cnr_800 -1000_2 Dr_Rev2.indd
Page 8
Magic Corner
Please refer to seperate instructions
included with your magic corner.
The middle shelf and hinges should be
discarded when using the magic corner.
For Step 1 in the
Magic Corner Instructions.
Use (Q) screws when xing the frame
to the cabinet.
For Step 4.
Use (Q) screws when xing the door
brackets to the door.
For Step 2.
Allow a 6mm (NOT 10mm) gap from front
edge when tting 22mm thick doors.
(Q) x2
15mm Screw
(Q) x6
15mm Screw

BASE UNIT
800 & 1000
Adjustable Corner
Assembly Guide
For Internal Use: FI.WR.INS.023_WKIN00105_BASE_Adj_Cnr_800 -1000_2Dr_Rev2.indd
Page 9
Securing to Adjacent Units
Screw into any side units using
the screws (L) provided to secure to
unit. At the top and bottom of both
sides of the unit, place a cover cap (M)
on the head to conceal it.
Hinge Mounting Plate
Attach hinge plates onto
panel (D) in locations shown
using 4 x 15mm screws (L).
(Ignore this step when tting
Magic Corner)
L Brackets
Use 2 x 15mm screws (L) to secure each
of the L brackets to the cabinets at either side.
Then screw up through into the worktop as
shown. Screws for attaching to worktop are
not supplied as these vary depending
on worktop material and thickness. Ensure
appropriate xings for attaching worktop
are used.
Worktop
Screw up through the front rail into
your worktop to secure it in place.
Screws for attaching to worktop are
not supplied as these vary depending
on worktop material and thickness. Ensure
appropriate xings for attaching worktop are
used.
L
L
Secure unit to wall using space plug.
Drill 2 evenly spaced pilot holes
through the back brace into the wall
and insert wall plugs. Then unwind
space plug until it contacts both
surfaces. Finally, tighten the screws.
Screws for attaching to walls are
not supplied.
D

BASE UNIT
800 & 1000
Adjustable Corner
Assembly Guide
For Internal Use: FI.WR.INS.023_WKIN00105_BASE_Adj_Cnr_800 -1000_2 Dr_Rev2.indd
Page 10
THE FOLLOWING STEPS ARE NOT REQUIRED FOR BIN UNITS
Step 17.
Insert hinge in top & bottom
holes as shown.
Step 18.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 19.
Attach the door to unit
where required. Adjust
hinges to suit. See below.
To attach door
clip hinge onto hinge
plate and click to secure.
Hinges
Hinge Cover Caps
Step 21.
Fit cover caps to hinge.
Step 20.
Adjust hinge to suit. As shown below.
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1- left - right
Point 2- side - side
12
FRONTAL HINGE
ADJUSTMENT
Hinge Plates
To Release door
Pull catch as shown,
to release hinge from the
hinge plate.
View from Inside of Carcass