Wren 972 L Corner User manual

BASE UNIT
972 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.024_WKIN00106_BASE_972_LCorner_Rev2.indd

BASE UNIT
972 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.024_WKIN00106_BASE_972_LCorner_Rev2.indd
Page 1
Legs
x9
Panel A
x1 Back Panel
Panel C
x1 Fixed Shelf
Panel B
x3 End Panels
Panel S
x1 2nd Back Panel
Panel T
x2 Fixed Shelf
Panel E
x2 Rail
Loose Shelf
x1 Large
Loose Shelf
x1 Small
Frontal
x2
Corner Post
Packed Seperately
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
Hinge Mounting Bracket
x4 Inc Screws
L Bracket
x2
Large L Bracket
x2
Space Plug
x2
XL Space Plug
x2
Hinge
x4 Inc Screws
(F) x16
Wooden
Dowel
(G) x12
Cam Dowel
(Expanding)
(H) x12
Cam Lock
(J) x8
45mm Screw
Black
(K) x4
30mm
Screw
(L) x76
15mm
Screw
(P) x2
Door Buer
(Z) x6
Shelf Peg
Plastic
(M) x10
Fixing Plate

BASE UNIT
972 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.024_WKIN00106_BASE_972_LCorner_Rev2.indd
Page 2
CARCASS 
Legs
x9
Step 1.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
Step 2.
Seat cam dowel
(G) into holes in
both end panels (B)
as shown.
Step 3.
Carcass construction
Attach panels (C) & (E) to panels (B),
using cam dowel (G) & cam lock (H) (in blue)
and also using dowels (F) (in orange)
in positions as shown.
Step 4.
Join panels (C) & (E) to (B).
Insert cam lock (H)
Do NOT tighten until Step 6.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening.
Do NOT use power tools with
cam dowel (G) or cam lock (H)
G
G
G
G
G G
GGF
F
F
F
F
F
F
F
FF
FF
B B
Dowel (F)
& Cam Dowel (G)
location detail
B
B
E
E
C
B
B
View from underside View from underside
H
G
G
H
Seat (G)
cam dowel
into hole as
shown.

BASE UNIT
972 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.024_WKIN00106_BASE_972_LCorner_Rev2.indd
Page 3
Step 5.
Slide back panel (A) into groove of panels (B).
Once back panel (A) is in position, ensure the
panel is ush & square with the bottom of the
end panels (B)
Step 6.
Hand tighten all cam locks (H),
this will expand the cam dowels
(G) and tighten the unit together.
Step 7.
Secure back panel (A) with
4x 30mm screws (K) equally
spaced at the bottom of back
panel (A) into base panel (C),
as shown.
Ensure you screw into the
centre of base panel (C)
(9mm from the bottom edge).
A
E
C
B
B
A
K
C
B

BASE UNIT
972 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.024_WKIN00106_BASE_972_LCorner_Rev2.indd
Page 4
Step 8.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
Step 9.
Seat cam dowel (G)
into holes in
both end panels (B)
as shown.
Step 10.
Carcass construction
Attach both panels (T) to panel (B),
using cam dowel (G) & cam lock (H) (in blue)
and also using dowels (F) (in orange)
in positions as shown.
Step 11.
Join both panels (T) to (B).
Insert cam lock (H) and tighten.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening.
DOWEL (F)
& CAM DOWEL (G)
LOCATION DETAIL
G
G
F
F F G
F G
B
CARCASS 
Do not use power tools with
cam dowel (G) or cam lock (H)
B
T
T
Seat (G)
cam dowel
into hole as
shown.
B
B
View from underside View from underside
H
G
G
H

BASE UNIT
972 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.024_WKIN00106_BASE_972_LCorner_Rev2.indd
Page 5
Step 12.
Secure panel (S) with 4x 45mm screws (J)
at the top and 4x 45mm screws (J) in the
bottom, in the holes provided as shown.
Step 13.
Secure both carcasses together using xing
plates (P) with 4x 15mm screws (L) to each
plate (P). Plates (P) should be positioned
equally spaced as shown.
S
T
T
B
L
L
L
L
P
P
P
P
PL
J
J
L
P

BASE UNIT
972 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.024_WKIN00106_BASE_972_LCorner_Rev2.indd
Page 6
Step 14.
Secure each of the legs into place with
2x 15mm screws (L)
Step 15.
Lightly hit centre peg of leg base
with a hammer until ush.
Step 16.
Push leg rmly down into the leg base.
Adjust legs to 155mm before turning
carcass upright. Once in situ level accordingly.
Ensure legs are rotated as shown so
that part of it is supporting the end
panels (B).
Front legs should have at edge to the
front.
Front
C
C
B
B
C
B
L
L
Leg position diagram
Front

BASE UNIT
972 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.024_WKIN00106_BASE_972_LCorner_Rev2.indd
Page 7
Step 17.
Attach Hinge Mounting Plate
onto both End Panels (B) as shown, using Screws which are
already positioned within the Hinge Plates.
Hinge side to be mounted in accordance to customer
kitchen plan.
Securing to adjacent units
Screw into any side units using the 30mm screws (K)
provided to secure to the unit. Screw just to the rear of the
hinge plate at the top and bottom of both sides of the unit,
place a cover cap (M) on the head to conceal it.
Worktop
Screw up through the front rail into your
worktop to secure it in place.
Screws for attaching to worktop are
not supplied as these vary depending
on worktop material and thickness.
Ensure appropirate xings for
attaching worktop are used please
refer to the specialist worktop
supplier if these are required for solid
surface worktops.
L Brackets
Use 2x 15mm screws (L) to secure each of the L brackets to
the cabinets at either side. Then screw up through into the
worktop as shown.
Screws for attaching to worktop are not supplied
as these vary depending on worktop material and
thickness. Ensure appropirate xings for attaching
worktop are used. L brackets should only be tted for
securing wood and laminate worktops, please refer to
the specialist worktop supplier if these are required for
solid surface worktops.
Carcass 1
Carcass 1
Carcass 2
XL Space
Plug
Space
Plug
Carcass 2
Secure unit to wall using space plugs. Drill 2 pilot holes through the
back brace into the wall and insert wall plugs. Then unwind space plug
until it contacts both surfaces. Finally, tighten the screws.
Screws for attaching to walls are not provided as these vary
depending on your wall material and construction. Ensure
appropriate xings for wall construction are used.
LL
126
126 94
94

BASE UNIT
972 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.024_WKIN00106_BASE_972_LCorner_Rev2.indd
Page 8
Step 18.
Align corner post to frontal. Equally space
2 xing plates (P) to the back of frontal
& corner post.
Ensure a 3mm gap is maintained between
frontal & post once xed together.
Screw in place using
4 x 15mm screws (L)
per xing plate (P).P
P
L
L
L
L
L
L
L
L
Step 19.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 20.
Attach the door to unit
where required.
To attach door
clip hinge onto hinge
plate and click to secure.
Hinge Cover Caps
Step 22.
Fit cover caps to hinge.
Step 21.
Adjust hinge to suit. As shown below.
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1- left - right
Point 2- side - side
1
2
FRONTAL HINGE
ADJUSTMENT
Hinge Plates
View from Inside of Carcass
To Release door
Pull catch as shown,
to release hinge
from the hinge plate.

BASE UNIT
972 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.024_WKIN00106_BASE_972_LCorner_Rev2.indd

BASE UNIT
972 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.024_WKIN00106_BASE_972_LCorner_Rev2.indd