Wren 2070 User manual

For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd Page 1
2250 x 600 Tall2070 x 600
1 Door
50/50 Door
70/30 Door
TOWER UNIT
2070 & 2250
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide

For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd Page 1
(FF) L Bracket SML
x6
L Bracket LGE
x4
(L) x142
15mm
Screw
(K) x6
30mm
Screw
Door Buer
x4
Metal Shelf Peg
x56
Plinth Attachment
(To order)
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Carcase (RH)
Right Hand
Carcase (LH)
Left Hand
Panel C
x1 Top Panel Frontals
50/50 or 1Dr or 70/30
Frontal Plinth
(To order)
Cabinet Plinth
(To order)
Hinge Mounting Plate
(To order) Inc Screws
Hinge
(To order) Inc Screws
Fixing Plate (U)
x19
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
70/30
OPTION
50/50
OPTION
1Dr
OPTION
(Packed Seperately)
Legs
x10
(M) x8
Cover Cap
(Per Colour)
TOWER UNIT
2070 & 2250
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide

For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd Page 2
TOWER UNIT
2070 & 2250
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide
Step 1.
Lay both carcases (LH) & (RH) at as shown.
Secure 5 x xing plate (U) positioned onto outside
face of panel (B) of carcase (RH) equally spaced
using 2 x 15mm screws (L) as shown.
Step 2.
Using 2 x 15mm screws (L) per plate secure
2 x xing plate (U) positioned onto outside
face of panel (C) of carcase (RH) using
measurements shown.
L
L
L
L
U
View from above
Carcase RH
View from above
Carcase RH
C
B
U
C
U
C
RH
LH B
RH
Fixing Plate diagram
View from Above
365mm
170mm
OUTSIDE
FACE
C
Front

For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd Page 3
Step 3.
Secure leg base into place with
2 x 15mm screws (L) per leg as shown.
Ensure legs are rotated to also provide
support to the end panels (B).
Front legs should have at edge to the
front.
L
Step 5.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning both carcase upright.
Once in situ level accordingly.
It is important to lift unit onto its legs. Do
not tilt as depicted in image.
A
BB
Front
RH A
FrontFrontFront
LH A
Leg position diagram
View From Underside
B
L
Step 4.
Lightly hit centre peg of leg
base with hammer until ush.
A
B
A
B
TOWER UNIT
2070 & 2250
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide

For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd Page 4
TOWER UNIT
2070 & 2250
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide
Step 6.
Position carcase LH and carcase RH together as shown.
Ensure carcases are ush & square.
View from rear of unit
Step 8.
Align 2 x L bracket SML (FF) combined with
2 x 15mm screws (L) per bracket as shown.
Secure carcase from inside the cabinet as shown.
Step 7.
Screw through xing plate (U)
into adjoining carcase LH using
2 x 15mm screws (L) to secure
both carcases together.
Repeat per xing plate (U).
L
L
L
TOWER UNIT
2070 & 2250
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide
U
U
U
U
U
U
U
LH
RH
Front
Front
Front
LH
RH
LH
RH
LL
LL
L
L
U
U
U
U
U
FF

For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd Page 5
Step 9.
Use 2 x 15mm screws (L) to secure each of the
4 x L brackets (LGE) to both carcases positioned as shown.
L
L
Step 10.
Screw through large L bracket (LGE) into the wall as shown.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction.
Ensure appropriate xings for wall constructions are used.
Fixings
to Wall
Front Front
TOWER UNIT
2070 & 2250
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide

For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd Page 6
TOWER UNIT
2070 & 2250
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide
Step 11.
When combined cabinet is secured in position, attach top Panel (C),
using 4x xing plates (U) combined with 4 x 15mm screws (L) per plate,
positioned as shown.
Step 12.
Measure plinth and cut to suit the width of carcase (LH) and again for (RH).
Mark clip positions by aligning plinth sections to legs. Use 2 x 15mm screws (L) as shown to x clip to plinth.
Detach the leg clip from the plinth clip. Slide leg clip into plinth clip as shown.
Top Panel C
U & L
U & LU & L
U & L
Plinth
Plinth
Leg
Brace
L
Step 13.
Secure plinth by pushing clip rmly onto legs, as shown.
Plinth
Plinth
TOWER UNIT
2070 & 2250
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide
LH RH
INSIDE
FACE
L

For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd Page 7
70/30
HINGE
POSITION
50/50
From Bottom From Bottom
From Top From Top
50/50 & 1 Door
HINGE
POSITION
L L
L L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
1826mm 1826mm
626mm
846mm
1336mm
866mm
1086mm
126mm 126mm
1794mm 1794mm
594mm
814mm
1304mm
834mm
1054mm
94mm 94mm
Front Front
70/30 1 Dr
Door
INSIDE
FACE
INSIDE
FACE
BB
BB
Step 14.
Attach hinge plates onto end panels (B) to suit as
shown using 2 x 15mm screws (L) included per plate.
Hinge side to be mounted in accordance to
customer kitchen plan.
TOWER UNIT
2070
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide

For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd Page 8
TOWER UNIT
2070 & 2250
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide
70/30
HINGE
POSITION
50/50
HINGE
POSITION
L
L
LL
L
L
L
L
L
L
L
LL
L
L
L
L
L
L
L
2006mm 2006mm
126mm 126mm
806mm
814mm
1394mm
626mm
1026mm
1516mm
1974mm 1974mm
94mm 94mm
774mm
846mm
1426mm
594mm
994mm
1484mm
TOWER UNIT
2250
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide
From Bottom From Bottom
From Top From Top
Front Front
70/30
BB
INSIDE
FACE
INSIDE
FACE
BB
Step 14.
Attach hinge plates onto end panels (B) to suit as
shown using 2 x 15mm screws (L) included per plate.
Hinge side to be mounted in accordance to
customer kitchen plan.
50/50

For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev8.indd Page 9
TOWER UNIT
2250
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide
126mm
94mm
1 Door
HINGE
POSITION
L
L
L
L
L
L
L
2006mm
1201.5mm
930.5mm
1169.5mm
898.5mm
1974mm
From Bottom
From Top
Front
1 Door
B
BB
INSIDE
FACE
Step 14.
Attach hinge plates onto end panels (B) to suit as
shown using 2 x 15mm screws (L) included per plate.
Hinge side to be mounted in accordance to
customer kitchen plan.
L