Wren TOWER UNIT 2070 User manual

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15
2070 - 2250
1 Door 50/50 Door 70/30 Door

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15
Screws and fixings for attaching to walls are not provided as these vary
depending on materials and construction. Ensure appropriate fixings for
wall are used.
BEFORE YOU START
INSTALLATION SHOULD BE PERFORMED BY A COMPETENT PERSON ONLY.
THIS PRODUCT COULD BE DANGEROUS IF INCORRECTLY INSTALLED
NOT to be used with
CAM DOWEL &
CAM LOCK

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 1
Panel A
x1 End Panel
Left Hand
Panel B
x1 End Panel
Right Hand
Panel C
x1 Back Panel
Left Hand
Panel D
x1 Back Panel
Right Hand
Panel sE
x1 Top Panel
Panel sM
x4 Fixed Shelf
Frontals
70/30, 50/50 or 1Dr
(Frontals and Plinth Packed Separately)
70/30
Option
1Dr
Option
50/50
Option

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 2
Hinge
Inc Screws
(F) x40
Wooden Dowel
(H) x20
Cam Lock
(K) x36
45mm Screws
(M) x8
Cover Cap
(W) x20
Cam Dowel
Hinge Mounting Plate
Inc Screws
Fixing Plate (U)
x4
Door Buer
x1
L Bracket LGE
x4
(L) x12
15mm Screws

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 3
Step 1.
Seat cam dowel (W) into holes in end panel (A) as shown.
A

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 4
Step 2.
Seat dowel (F) into holes in end panel (A) as shown.
A

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 5
Step 3.
Attach panels (sM) and (sE) to end panel (A), using cam dowel (W) and dowels (F) in positions as shown.
Panel (sE) cam holes to face the outside of the unit.
Panels (sM) cam holes to face downwards.
Step 4.
Insert cam locks (H). Do NOT tighten until Step 7.
sM sM sM sM
sE
F
W
H
A
A

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 6
A
Step 5.
Seat 20 x dowels (F) into holes in panels (sM) and (sE) as shown.
sM
sM
sM
sM
sE

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 7
A
C
Step 6.
Slide back panel (C) into groove of end panel (A). Also insert dowels (F) from
panels (sM) and (sE) into the required holes in back panel (C).
Once back panel (C) is in position, ensure the panel is ush & square with bottom
of end panel (A) and secure in place with 15 x 45mm screws (K) through panel (C)
into panels (sM) and (sE).
A
C
sM
sM
sM
sM
sE
View from underside

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 8
Step 8.
Secure back panel (C) to end panel (A) at the bottom using 1 x L bracket LGE as shown. Secure the L Bracket
LGE in place with 4 x 15mm screws (L).
A
C
sM
sM
sM
sM
sE
A
C
Step 7.
Hand tighten all cam locks (H), this will expand cam dowels (W)
and tighten the unit together.

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 9
Step 9.
Seat cam dowel (W) into holes in end panel (B) as shown.
B

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 10
Step 10.
Seat dowel (F) into holes in end panel (B) as shown.
B

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 11
Step 11.
Attach end panel (B) to panels (sM) and (sE) using cam dowel (W) and dowels (F) in positions as shown.
Step 12.
Insert cam locks (H). Do NOT tighten until Step 17.
A
B
C
sM
sM
sM
sM
sE

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 12
Step 13.
Slide back panel (D) into groove of end panel (B). Also insert dowels (F) from
panels (sM) and (sE) into the required holes in back panel (D).
Once back panel (D) is in position, ensure the panel is ush & square with bottom
of end panel (B) and secure in place with 21 x 45mm screws (K) through panel (D)
into panels (sM) and (sE).
Step 14.
Secure back panel (D) to end panel (B) at the bottom using 1 x L bracket LGE as shown. Secure the L Bracket
LGE in place with 4 x 15mm screws (L).
A
B
C
D
View from underside

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 13
Step 15.
Hand tighten all cam locks (H), this will expand cam dowels (W)
and tighten the unit together.
Step 15.
Ensure that the tower is positioned correctly and level. Secure the tower to the wall using 2 x L brackets
LGE. Use 2 x 15mm screws (L) provided to secure each of the L brackets LGE to the top, rear of the unit
at either side. Then screw through the bracket into the wall using an appropriately size screw as shown.
Screws not provided.

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 14
2070 - 70/30
HINGE POSITION 2070 - 50/50 & 1 Dr HINGE POSITION
A or B A or B
276mm 276mm
776mm
1016mm
996mm
1236mm
1976mm 1976mm
1486mm
244mm 244mm
744mm
984mm
964mm
1204mm
1944mm 1944mm
1454mm
Front Front
70/30 50/50
1 Dr
INSIDE
FACE
INSIDE
FACE
From Bottom From Bottom
2070
Step 19.
Attach hinge plates onto end panel (A) or (B) to suit as shown using screws already positioned within the hinge
plate. Hinge side or sides to be mounted in accordance to Customer Specic Kitchen Plan.

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 15
2250 - 70/30
HINGE POSITION 2250 - 50/50 HINGE POSITION
A or B A or B
276mm 276mm
776mm
956mm
996mm
1176mm
2156mm 2156mm
1576mm
1666mm
244mm 244mm
744mm
924mm
964mm
1144mm
2124mm 2124mm
1544mm
1634mm
Front Front
70/30 50/50
INSIDE
FACE
INSIDE
FACE
From Bottom From Bottom
2250
Step 19.
Attach hinge plates onto end panel (A) or (B) to suit as shown using screws already positioned within the hinge
plate. Hinge side or sides to be mounted in accordance to Customer Specic Kitchen Plan.

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 16
2250 - 1 Door
HINGE POSITION
A or B
276mm
1080.5mm
1351.5mm
2156mm
244mm
1048.5mm
1319.5mm
2124mm
Front
1 Dr
INSIDE
FACE
From Bottom
2250
Step 19.
Attach hinge plates onto end panel (A) or (B) to suit as shown using screws already positioned within the hinge
plate. Hinge side or sides to be mounted in accordance to Customer Specic Kitchen Plan.

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 17
1 DOOR
OPTION
Hinge Attachment and Adjustment
Doors supplied in accordance to customer specic kitchen plan
50/50
&
70/30
OPTIONS
Step 2. (Where applicable)
Align frontals and join together
using 2 x xing plates to the back of
both frontals. Ensure a 4mm gap is
maintained between each frontal.
Screw in place using 4 x 15mm
screws (L) per xing plate. Fixing Plate
Hinge dowels
Step 1.
Insert hinges into frontal hinge holes
provided, secure hinges with the 2
x screws and hinge dowels already
located in the hinges.
Step 3.
Attach the door to unit, clip hinges onto hinge
plates and click to secure.

TOWER UNIT
2070 & 2250 Walk In Tower Assembly Guide
For Internal Use: FI.WR.INS.014_WKIN0062_Walkin_Tower_Guide_Rev15 Page 18
The top and bottom hinges MUST be adjusted to the SAME STRENGTH.
Step 5.
Fit cover caps to hinges and adjust soft-close to suit.
Step 4.
Adjust hinges to suit, using the highlighted screws shown.
A
A
B
C
A
B
C