Wren 700 User manual

WALL UNIT
700 - 800 2 Door
Assembly Guide
For Internal Use: FI.WR.INS.035_WKIN00125_WALL_700 _800_2Door_Rev4.indd
700
800

WALL UNIT
700 - 800 2 Door
Assembly Guide
For Internal Use: FI.WR.INS.035_WKIN00125_WALL_700 _800_2Door_Rev4.indd
Page 1
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Panel A
x1 Back Panel
Hanging Bracket
X2 Inc Screws
(F) x8
Wooden Dowel
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x4
30mm
Screw
(L) x8
15mm
Screw
(S) x4
20mm
Screw
(M) x4
Cover Cap
(N) x2
Door
Buer
(Z) x10
Shelf Peg
Plastic
(T) x12
Back Panel
Support Clip
Hanging Bracket Plate
X2 (Screws Not Included)
Hinge Mounting Plate
X4 Inc Screws
Hinge
X4 Inc Screws
Corner Gusset
X2
Hanging Bracket
Cover Cap
X2
Panel B
x2 End Panel
Panel C
x2 Base Panel
Frontal
(packed separately)
x1
Shelf
x2
View from underside

WALL UNIT
700 - 800 2 Door
Assembly Guide
For Internal Use: FI.WR.INS.035_WKIN00125_WALL_700 _800_2Door_Rev4.indd
Page 2
Step 1.
Seat dowel (F)
into holes in end
panel (B) as shown.
Step 2.
Seat cam dowel
(G) into holes in end
panel (B) as shown.
Step 3.
Attach panels x2 (C) to panel
(B), using cam dowels (G)
& cam locks (H) (in blue),
and also using dowels (F)
(in orange) in positions as
shown.
Step 4.
Slide panel (A) into the groove
of panels (B) and x 2 (C).
Step 5.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the
cam dowels (G) and
tighten the unit together.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
A
C
C
Seat (G)
cam dowel
into hole as
shown.
Dowel (F)
& Cam Dowel (G)
location detail
G
G
F
F
F
F
G
G
B
View from underside View from underside
B
CC
H
H
G
G

WALL UNIT
700 - 800 2 Door
Assembly Guide
For Internal Use: FI.WR.INS.035_WKIN00125_WALL_700 _800_2Door_Rev4.indd
Page 3
Step 6.
Seat dowel (F) into
holes in both panels (B)
as shown.
Step 7.
Seat cam dowel (G)
into holes in both
end panels (B) as
shown.
Step 8.
Attach panel (B) to panels
(C) using cam dowels (G)
& cam lock (H) (in blue)
and also using dowels (F)
(in orange) in positions as
shown. Ensure panel (A) is
seated into the groove of
panel (B).
Step 9.
Insert cam lock (H).
Hand tighten all cam
locks (H), this will expand
the cam dowels (G) and
tighten the unit together.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening. Do not use power tools with
cam dowel (G) or cam lock (H)
B
B
A
C
C
Seat (G)
cam dowel
into hole as
shown.
Dowel (F)
& Cam Dowel (G)
location detail
G
G
F
F
F
F
G
G
B
View from underside View from underside
B
CC
H
H
G
G

WALL UNIT
700 - 800 2 Door
Assembly Guide
For Internal Use: FI.WR.INS.035_WKIN00125_WALL_700 _800_2Door_Rev4.indd
Page 4
Step 12.
Attach Hinge Mounting Plate
onto both End Panels (B) as shown,
using Screws which are already
positioned within the Hinge Plates.
Hinge side to be mounted in
accordance to customer kitchen
plan.
Step 11.
Slide the back panel clips (T) into the groove of
both panels (B) & (C). The back panel clips (T)
should be evenly spaced as shown and positioned
to allow the hanging bracket and corner gussets
to be tted. Once in place, tighten screw.
Step 10.
Ensure carcass is
square.
BA
A
C
T
A
T
126 94
94
126

WALL UNIT
700 - 800 2 Door
Assembly Guide
For Internal Use: FI.WR.INS.035_WKIN00125_WALL_700 _800_2Door_Rev4.indd
Page 5
Step 13.
Step 13a.
Insert hanging
bracket into pre-drilled
holes
Step 13b.
Rotate locking
lever 180 degrees
Step 13c.
Secure with provided
2 x 20mm screws (S) per bracket
Step 14.
Secure corner gussets to the bottom left and
right hand side of the wall unit using
4 x 15mm screws (L) per plate.
Step 15.
Drill a small pilot hole through the centre of the corner gussets.
Use this hole at the end of the process to screw through and into
the wall. Cover the screw heads using the cover caps (M) provided.
Screwsforxingtowallsarenotprovidedasthesevary
dependingonyourwallmaterialandconstruction.Ensure
appropriatexingsforwallconstructionsareused.
S
S
L
L
M
L
L

WALL UNIT
700 - 800 2 Door
Assembly Guide
For Internal Use: FI.WR.INS.035_WKIN00125_WALL_700 _800_2Door_Rev4.indd
Page 6
Step 16.
Measure appropriately and attach
the 2 x hanging bracket plates
onto the wall screwing through
the provided holes into your wall.
Screws for xing to walls are not
provided as these vary depending on
your wall material and construction.
Ensureappropriatexingsforwall
construction are used. Hang the
cabinet using the brackets to hook
onto the plate as shown below.
Step 18.
Screw into any side units using the provided 2x 30mm screws (K)
to secure the unit. Screw just to the rear of the hinge plate then
place a cover cap on the head to conceal it.
Step 17a.
Rotate the screw clockwise
to move the cabinet up.
Anti-clockwise for down.
Step 17b.
Adjust the depth
using centre screw.
Step 17c.
Screw the red
screw until it
touches the plate
to lock in position.
K

WALL UNIT
700 - 800 2 Door
Assembly Guide
For Internal Use: FI.WR.INS.035_WKIN00125_WALL_700 _800_2Door_Rev4.indd
Page 7
Step 19.
Insert hinge in top & bottom
holes as shown.
Step 20.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 21.
Attach the door to unit
where required.
To attach door
clip hinge onto hinge
plate and click to secure.
Hinges
Hinge Cover Caps
Step 23.
Fit cover caps to hinge.
Step 22.
Adjust hinge to suit. As shown below.
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1- left - right
Point 2- side - side
1
2
FRONTAL HINGE
ADJUSTMENT
Hinge Plates
View from Inside of Carcass

WALL UNIT
700 - 800 2 Door
Assembly Guide

WALL UNIT
700 - 800 2 Door
Assembly Guide

WALL UNIT
700 - 800 2 Door
Assembly Guide