XMark Fitness XM-4467.1 User manual

Owner’s Manual
Read all precautions and instructions in this manual before using this equipment.
Dumbbell and Plate
Rack with Bar Storage
XM-4467.1
9/20

2
Table of Contents
3
3
4-5
6
Before You Start
Important Safety Information
Assembly
Exploded View/Parts List

Before You Start
3
THANK YOU for making this unit a part of your exercise program.
XMark assures the very best in value, appearance, durability and
biomechanics.
•This unit should only be used on a level surface and is intended for indoor use
only. XMark recommends an equipment mat be placed under the unit to protect
the floor or carpet and for easier cleaning.
•Always examine your unit before using to ensure all parts are in working order.
•Do not leave children unsupervised near or on the unit.
This manual will guide you through the assembly process. If at any time you are having
trouble with the assembly or use of this product, please contact our Customer Service
department. We have trained service technicians on site to assist you.
Visit www.xmarkfitness.com for warranty information
SAFETY INFORMATION WARNING!
Before using this unit or starting any exercise program, consult your physician. This is
especially important for persons over the age of 35 and/or persons with pre-existing
health problems. XMark assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
It is the owner’s responsibility to ensure that all users of this unit have read the Owner’s
Manual and are familiar with safety information and precautions.
SAFETY PRECAUTIONS

Assembly
4
9
9
99
8
12
12
14
3
8
10
2
2
1
1
3
11
13
13 13
13
4
4
4
4
12
12
12
12
11
11 11
Attach the Plate Dividers (#9) to
the Crossbar (#8) using:
•8 x Bolts (#14)
•8 x Washers (#12)
Tighten all bolts firmly.
Attach the Right Upright (#1) and
Base (#3) to the Crossbar (#8)
using:
•2 x Bolts (#10)
•2 x Locknuts (#11)
During STEP 2-6 be sure to only hand tighten
nuts and bolts until unit is completely
assembled. If bolts are too tight after this step
it will cause alignment issues later during the
installation.
Lower rail goes in the front.
_____
Attach the Left Upright (#2) and
Base (#3) to the Crossbar (#8)
using:
•2 x Bolts (#10)
•2 x Locknuts (#11)
Build the middle shelf by attaching the
Angle Iron Shelving (#4) to the
middle brace of the Left Upright (#2)
and Right Upright (#1) using:
•4 x Bolts (#13)
•4 x Washers (#12)
•4 x Locknuts (#11)
STEP 4:
Build the top shelf by attaching the
Angle Iron Shelving (#4) to the top
brace of the Left Upright (#2) and
Right Upright (#1) using:
•4 x Bolts (#13)
•4 x Washers (#12)
•4 x Locknuts (#11)
STEP 5:
STEP 1:
STEP 2:
STEP 3:

Assembly
5
18
15
15
12
11
3
3
18
Attach the Bar Holders (#18) to the
Bases (#3) using:
•4 x Bolts (#15)
•4 x Washers (#12)
•4 x Locknuts (#11)
STEP 6:
Wrench tighten all nuts and bolts
STEP 7:

Exploded View/Part List
1
2
3
3
4
4
4
4
5
5
6
6
6
6
6
66
6
7
7
7
7
10
10
11
11
11
11
11
11
11
11
11
11
12
12
12
12
12
12
12
12
12 12
13
13
13
13
13
13
13
13
15
15
16
19
16
19
17
17
18
20
20
18
Key No. Description Qty. Key No. Description Qty.
1 1
10 4
2 1
11 16
3 2
12 20
4 4
13 8
5 2
14 8
6 8
15 4
7 4
16 2
8 1
17 2
9
Right Upright
Left Upright
Base
Angle Iron Shelf
50mm Inner Cap
44mm Inner Cap
Square End Cap
Crossbar
Plate Divider
4
18
M10 x 73mm Bolt
M10 Locknut
M10 Washer
M10 x 63mm Bolt
M10 x 30mm Bolt
M10 x 68mm Bolt
Foot
Base Inner Cap
Bar Holder
2
19
M4 x 19mm Screw
2
20
Bushing
2
6
12 12
12
12 12
8
11
11
12
12
14 14
14
14
14 12
9
9

Customer Service Email: [email protected]