XMark Fitness XM-4419 User manual

Owner’s Manual
8/09
XM-4419
Read all precautions and
instructions in this manual before
using this equipment.
FID BENCH with
LEG & PREACHER

2
Table of Contents
Important Safety Information
Assembly
Parts List
Exploded View
Warranty Information
4
5-11
12
13
14

3
MODEL: XM-4419
XM-4419
This manual will guide you through the assembly process. If at any time you
are having trouble with the assembly or use of this product, then please contact
When calling please have the following product information available:
Model Name :
Date Mfg.:
Serial #
Model Name Decal Location
Before You Start
REGISTRATION CARD
QUESTIONS?
CALL 1-800-719-4605
Monday-Friday
8:30 a.m.-5:00 p.m.
(Central Standard Time)
MAILING ADDRESS
7501 Trammel Drive
Shreveport, LA 71108
THANK YOU for making this unit a part of your exercise
program.
XMARK Fitness assures the very best in value,
appearance, durability and biomechanics.
XMARK FITNESS SERIES
XMARK Fitness
To avoid unnecessary delays in warranty parts and to insure that a permanent
record of your purchase is on file with our company, be sure to send in the war-
ranty registration card or register online at www
.xmarkfitness.com within 10 days
of purchase.
us at our
XMARK Fitness help line. We have trained service technicians on site to
take care of you, our valued customer.

NOTE: Hand tighten bolts and nylon nuts until machine is fully
assembled.
SAFETY PRECAUTIONS
SAFETY INFORMATION WARNING!
Prior to assembly, remove components from the box and verify that all the listed parts
were supplied.
Before using this unit or starting any exercise program, consult your physician.
This is especially important for persons over the age of 35 and/or persons with pre-
existing health problems. XMARK Fitness assumes no responsibility for personal
injury or property damage sustained by or through the use of this product.
It is the owner’s responsibility to ensure that all users of this unit have read the
Owner’s Manual and are familiar with safety information and precautions.
• This unit should only be used on a level surface and is intended for indoor use
only. XMARK Fitness recommends an equipment mat be placed under the unit to
protect the floor or carpet and for easier cleaning.
• Wear comfortable, good-quality walking or running shoes and appropriate cloth-
ing. Do not use this unit with bare feet, sandals, socks or stockings!
• Always examine your unit before using to ensure all parts are in working order.
• Do not leave children unsupervised near or on the unit.
• Service to your unit should only be performed by an authorized service represen-
tative, unless authorized and/or instructed by a XMARK Fitness technician. Failure
to follow these instructions will void the warranty.
Important Safety Information
4

5
NOTE: Hand tighten bolts and locknut until machine is fully assembled.
STEP 1
STEP 2
Assembly
23
23
23
23
10
33
41
920
1
Attach the U-Shaped Front Base (2)
to the front part of the Main Frame (1),
and secure with three M10 washers (39),
three M10X15 Allen Bolts (31).
Insert the Rear Base (3) into the rear
part of the Main Frame (1) with two
M10X15 Allen Bolts (31) and two
M10 Washers (39).
Pull the Pop Pin (20) as far as it will
go and slide Sliding Block (9) onto
Incline Adjustment Tube (10). Push
two Spacers (23) into the Sliding Block
(9).
Push two Spacers (23) into the Incline
Adjustment Tube (10).Then attach Incline
Adjustment Tube (10) to the bracket on
the Main Frame (1). Secure with one M10X75
Allen Bolt (33) and one M10 Lock Nut (41).
Push four Spacers (23) into the Main
Frame (1) as illustrated.
23
23
23
23
2
39 39
31
31
31
33
41
1
3
31
31
39 39

6
NOTE: Hand tighten bolts and lock nuts until machine is fully assembled.
STEP 3
Assembly
6
1
32
39
23
23
41 39
39
7
7
23
32
35
39
6
Push two Spacers (23) into each Seat Supports (6).
Attach one Backrest Support (7) to one Seat Support (6). Align the holes with one M10X45 Allen
Bolt (32) and one M10 Washer (39). Repeat to complete the assembly of the remaining parts
(6) (7).
Attach the two Backrest Supports (7) to the pivot on the Main Frame (1) with one M10X160 Allen
Bolt (35), two M10 Washers (39) and one M10 Lock Nut (41).

7
STEP 4
NOTE: Hand tighten bolts and locknuts until machine is fully assembled.
Assembly
35
39
39
41
910
7
7
Connect the Sliding Block (9) and the Backrest Supports (7) with one M10 x160 Allen
Bolt (35), two M10 Washers (39) and one M10 Lock Nut (41).

8
NOTE: Hand tighten bolts and lock nuts until machine is fully assembled.
Assembly
STEP 5
39
36
39
6
1
41
823
23
Attach the Seat Adjustment Bracket (8)
to the Seat Supports (6) with M10X205 Allen
Bolt (36), two M10 Washers (39) and one
M10 Lock Nut (41).
Do not over tighten the Lock Nut and Bolt.
The Bracket needs to be able to swivel.
Push two Spacers (23) into the Seat Adju-
stment Bracket (8).
STEP 6 14
15
16
67
37
37
37 37
37
37
40 40 40
40 40
40 40
40
40
Attach the Upper Back Pad (15) and
Lower Back Pad (16) to the backrest
Supports (7) using eight Allen Bolts
M6x55 (37) and eight Washers M6 (40).
Attach the Seat Pad (14) to the Seat
Supports (6) using four M6X55 Allen
Bolts (37) and four Washers M6 (40).

9
NOTE: Hand tighten bolts and lock nuts until machine is fully assembled.
Assembly
41
6
43 6
8
Connect the Seat Supports (6) and the Seat Adjustment Bracket (8) with one
M10 x 120 Allen Bolt (34) and one M10 Lock Nut (41).
STEP 7

10
STEP 8
STEP 9
NOTE: Hand tighten bolts and lock nuts until machine is fully assembled.
Assembly
20
17
31
21
Attach the Curl Pad (21) to the Arm Curl
Stand (17) using two M10X15 Allen Bolts
(31).
Insert Arm Curl Stand (17) into the Main
Frame (1) and secure in place using the
Locking Pop Pin (20).
1
23
23
33
41
5
Push two Spacers (23) into Leg Lift Bar (5).
Attach the Leg Lift Bar (5) to the Main Frame
(1) with one M10X75 Allen Bolt (33) and one
M10 Lock Nut (41).