XMark Fitness XM-4432 User manual

Owner’s Manual
XM-4432
POWER TOWER

2
Table of Contents
Before You Begin 3
Assembly 5
Parts List 9
Exploded View 10
NOTE: Hand tighten bolts and locknuts until machine is fully
assembled.Lock nuts may require additional force to tighten
completely
SAFETY PRECAUTIONS
SAFETY INFORMATION WARNING!
Prior to assembly, remove components from the box and verify that all the listed parts
were supplied.
Before using this unit or starting any exercise program, consult your physician.
This is especially important for persons over the age of 35 and/or persons with pre-
existing health problems.
It is the owner’s responsibility to ensure that all users of this unit have read the
Owner’s Manual and are familiar with safety information and precautions.
• This unit should only be used on a level surface and is intended for indoor use
only. XMARK Fitness recommends an equipment mat be placed under the unit to
protect the floor or carpet and for easier cleaning.
• Wear comfortable, good-quality walking or running shoes and appropriate cloth-
ing. Do not use this unit with bare feet, sandals, socks or stockings!
• Always examine your unit before using to ensure all parts are in working order.
• Do not leave children unsupervised near or on the unit.

NOTE: Hand tighten bolts and locknuts until machine is fully assembled.
Lock nuts may require additional force to tighten completely.
STEP 2
STEP 1
Assembly
Insert the bar on the Lower Support (4) into the
Left Base (2), securing with M8 x 20 Bolt (A6)
Insert the Lower Upright (6) into the Left Base (2)
securing with four M10 x 20 Bolts (A1) and four
M10 Washers (B1).
Connect the Lower Support (4) and the Lower
Upright (6) with Square Bracket (5), three M10x70
Bolts (A2) and three M10 Lock Nuts (C1).
Repeat to complete the assembly for the Right
Base (1), the Lower Support (4) and the Lower
Upright (6) on the right side (not shown).
Connect Left Base (2) and Right Base (1) with
Bottom Brace (9), securing with four M10 x 70
Connect the Lower Uprights (6) with the Lower
Cross Brace (7) and two Square Brackets (5),
using four M10 x 70 Bolts (A2) and four M10
Lock Nuts (C1).
4
5
A2
A2
A2
A2
4
9C1
C1
C1
C1
C1
C1
C1
C1
7
6
6
A2
5
C1
A2
A2
B1
B1
B1
A1
A1
2
A2
B2
4
C1
6
and M8 Washer (B2)
Bolts (A2) and four M10 Lock Nuts (C1).
1
2
A6

NOTE: Hand tighten bolts and locknuts until machine is fully assembled.
Lock nuts may require additional force to tighten completely.
Assembly
5
STEP 3
Install the Sit-up Bar (8) into the bracket on the Lower Cross Brace (7) and secure with
two Ring Head Lock Pins (24).
Slide the Foam Rollers (23) onto each end of the Sit-up Bar (8) and secure with Foam
Roller Caps (10).
24
8
7
10
10
23
23

NOTE: Hand tighten bolts and locknuts until machine is fully assembled.
Lock nuts may require additional force to tighten completely.
Assembly
A1
A1
A1
A1
B1
B1
B1
B1
66
11
11
STEP 4
6
Insert the Upper Upright Tubes (11) to the Lower Upright Tubes (6) and secure with four
M10x20 Bolts (A1) and four M10 Washers (B1).

7
NOTE: Hand tighten bolts and locknuts until machine is fully assembled.
Lock nuts may require additional force to tighten completely.
STEP 5
STEP 6
Assembly
C1
C1
13
13
A1
A1
A1
A1
A2
12
11
11
6
6
A2
A2
A2
A2
A3
18
B1
C1
C1
11
11
13
14
14
13
6
6
A3
B1
A2
A1
Attach the Extended Arms (13) through
the joints of the Upper and Lower
Upright Tubes (11& 6) to the Upper
Cross Brace (12). Secure them with four
M10x20 Bolts (A1), two M10x70 Bolts (A2)
and two M10 Lock Nuts (C1).
Attach the Upper Support Bars (14)
to the Extended Arms (13) and the
Lower Upright Tubes (6). Secure using
four M10x70 Bolts (A2) and four M10
Lock Nuts (C1). Attach the Pull-up Bar (18)
to the Upper Upright Tubes (11) and
secure with two M10x55 Bolts (A3)
and two M10 Washers (B1).

8
STEP 7
A4
B2
A5
B2
19
20
NOTE: Hand tighten bolts and locknuts until machine is fully assembled.
Lock nuts may require additional force to tighten completely.
il
Assembly
13
12
19 13
Congratulations! You have completed assembly of your XM-4432.
Attach one Arm Pad (19) to oneExtended Arm (13) and secure with two M8x70 Bolts
(A4) and two M8 Washers (B2). Repeat thisstep to complete the assembly for the other
side. Attach the Back Pad (20) to the Upper Cross Brace (12) and secure with two M8x40
Bolts (A5) and two M8 Washers (B2).

9
Parts List
XM-4432 Parts List
Key NO. QTY
1RIGHT BASE XM-4432 1
2LEFT BASE XM-4432 1
3PLASTIC HANDLE GRIP 4
4LOWER SUPPORT XM-4432 2
5SQUARE BRACKET, XM-4432 4
6LOWER UPRIGHT XM-4432 2
7BRACE, LOWER CROSS XM-4432 1
8SIT-UP BAR 1
9BOTTOM CROSS BRACE XM-4432 1
10 FOAM ROLLER CAP 2
11 UPPER UPRIGHT XM-4432 2
12 UPPER CROSS BRACE XM-4432 1
13 EXTENDED ARM XM-4432 2
14 UPPER SUPPORT XM-4432 2
15 MID FOAM GRIP XM-4432 4
16 LONG FOAM GRIP XM-4432 1
17 CONNECTIVE HEAD XM-4432 2
18 PULL UP BAR / XM-4432 1
19 ARM PAD XM-4432 2
20 BACK PAD XM-4432 1
21 SQUARE END FOOT F50 4
22 2" SQUARE SLEEVE XM-4432 2
23 FOAM ROLLER 2
24 RING HEAD LOCK PIN 2
A1 BOLT, M10X20 16
A2 BOLT, M10X70 20
A3 BOLT M10X55, 2
A4 BOLT, M8X70 4
A5 BOLT, M8X40 2
A6 BOLT, M8X20 2
B1 WASHER M10 14
B2 WASHER M8 8
C1 LOCK NUT, M10 20
25 BOLT PACK XM-4432 1
26 MANUAL XM-4432
1
Description

Exploded View
10
17
17
11
11
10
10
16
B1
B1
A3 A3
18 15
15
A2
A2
A1
A1
A5
A5B2
B2
B2
B2
B2
B2
12
20
3
3
3
3
19
19
13
13
A4
A4
22
22
A2
A2
A2
A2
C1
C1
C1
C1
C1
C1
14
14
6
C1
C1
C1
C1
C1
C1
C1
C1
C1
C1
7
823
23 10
10
9
A2
A2
A2
A2 A2
A2
A2
A2
A2
B1
B1 B1
B1
A1
A1
A1
2
21
24
15
15
21
21
21
A6
A6
B2
B2
55
6
1
A1
A1
A1
B1
B1
A1
A1
A1
B1 B1
A1
4
4
5