XMark Fitness XM-7618 User manual

Owner’s Manual
XM-7618
8|20
LAT MACHINE

Table of Contents
3
4
5-12
13
14
Important Safety Information
Before You Start
Assembly
Parts List
Exploded View
2

NOTE: Hand tighten bolts and nylon nuts until machine is fully
assembled.
Prior to assembly, remove components from the box and verify that all the listed parts
were supplied.
SAFETY INFORMATION WARNING!
Before using this unit or starting any exercise program, consult your physician.
This is especially important for persons over the age of 35 and/or persons with
pre-existing health problems. XMark assumes no responsibility for personal injury
or property damage sustained by or through the use of this product.
It is the owner’s responsibility to ensure that all users of this unit have read the
Owner’s Manual and are familiar with safety information and precautions.
SAFETY PRECAUTIONS
•This unit should only be used on a level surface and is intended for indoor use
only. XMark recommends an equipment mat be placed under the unit to protect
the floor or carpet and for easier cleaning.
•Walking or running shoes and the appropriate clothing should be worn when using
this unit
•Always examine your unit before using to ensure all parts are in working order.
•Do not leave children unsupervised near or on the unit.
•Service to your unit should only be performed by an authorized service represen-
tative, unless authorized and/or instructed by a XMark technician. Failure to
follow these instructions will void the warranty.
Important Safety Information
3

This manual will guide you through the assembly process. If at any time you
are having trouble with the assembly or use of this product, then please contact
Before You Start
QUESTIONS?
EMAIL: [email protected]
THANK YOU for making this unit a part of your exercise
program. XM ark assures the very best in value, appearance,
durability and biomechanics.
us at our
XMark help line. We have trained service technicians on site to take
care of you, our valued customer.
Please visit www.xmarkfitness.com for warranty information
'

Assembly
5

Assembly
     
 x    
 x
  (#31)
 x   #37)
-Make sure the 3 holes of Rear Base (#2) are on the top!
      
  x    
 x   (#31)
S TE P 2 :
S TE P 1 :
NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
 !

Assembly
Slide Weight Bumpers (#24) and Weight Support (#12) onto Guide Rods (#9) as shown.
•2 x Button Head Cap Screws(#33)
•4 x Flat Washers (#31)
•2 x Nylon Locknuts(#37)
Attach Seat Support (#6) to Main Base (#1) using:
•2 x Button Head Cap Screws(#33)
•4 x Flat Washers (#31)
•2 x Nylon Locknuts(#37)
7
S TE P 3 :
S TE P 5 :
Connect Upright (#3) to the Main Base (#1) using:
NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
S TE P 4 :

Slide Top Cross Frame (#5) on top of Guide Rods (#9) and secure using:
•2 x Button Head Cap Screws(#36)
•2 x Flat Washers (#31)
Attach Top Frame (#4) to the Upright (#3) using:
•2 x Button Head Cap Screws(#33)
•2 x Nylon Locknuts(#37)
•4 x Flat Washers (#31)
Attach Top Frame (#4) to the Top Cross Frame (#5) using:
•2 x Button Head Cap Screws (#34)
•2 x Nylon Locknuts(#37)
•4 x Flat Washers (#31)
Attach Lat Bar Hook (#8) to Top Frame (#4) using:
•1 x Button Head Cap Screw (#32)
•1 x Nylon Locknut (#37)
•2 x Flat Washers (#31)
8
Assembly NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
S TE P 7 :
S TE P 6 :
S TE P 8 :
S TE P 9 :

Start by attaching the High Pully Cable (#15) to Slide Weight Support (#12) using:
•1 x 1/2"-12 Jam Nut (#44)
Attach aPulley (#21) to the Top Frame (#4) using:
•1 x Button Head Cap Screw (#38)
•1 x Nylon Locknut (#37)
•2 x Flat Washers (#31)
•1 x Button Head Cap Screw (#38)
•1 x Nylon Locknut (#37)
•2 x Flat Washer (#31)
9
Assembly NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
S TE P 10 :
S TE P 11 :
S TE P 12 :Attach two Pulleys (#21) to the Pulley Plates (#28)using:

Route the Low Pulley Cable by feeding the cable through the seat post, upright Frames the up
and over the lower pulley on the pulley plates. Finish by screwing the jam nut into the main
base.
Assembly NOTE: Hand tighten bolts and Nylon Lock nuts until machine is fully assembled.
S TE P 14 :
Attach two Pulleys (#21) to the Top Frame (#4) using:
•2 x Button Head Cap Screw (#33)
•2 x Nylon Locknut (#37)
•4 x Flat Washer (#31)
•4 x Pulley Spacer (#29)
S TE P 13 :
Before STEP 13 route the UPPER CABLE as shown making sure the cable is routed over
the 2 Button Head Cap Screws (#38). Not doing so will damage the cable!
STEP 13
STEP 14
STEP 15