XMark Fitness XM-4430 User manual

8/09
Owner’s Manual
!CAUTION
Read all precautions and
instructions in this manual before
using this equipment.
POWER CAGE
XM-4430

2
Table of Contents
Important Safety Information 4
Before You Begin 3
8-5ylbmessA
9
tsiLstraP 10
weiVdedolpxE
11noitamrofnIytnarraW

3
MODEL: XM-4430
XM-4430
This manual will guide you through the assembly process. If at any time you
are having trouble with the assembly or use of this product, then please contact
When calling please have the following product information available:
Model Name :
Date Mfg.:
Serial #
Model Name Decal Location
Before You Start
REGISTRATION CARD
QUESTIONS?
CALL 1-800-719-4605
Monday-Friday
8:30 a.m.-5:00 p.m.
(Central Standard Time)
MAILING ADDRESS
7501 Trammel Drive
Shreveport, LA 71108
THANK YOU for making this unit a part of your exercise
program.
XMARK Fitness assures the very best in value,
appearance, durability and biomechanics.
XMARK FITNESS SERIES
XMARK Fitness
To avoid unnecessary delays in warranty parts and to insure that a permanent
record of your purchase is on file with our company, be sure to send in the war-
ranty registration card or register online at www
.xmarkfitness.com within 10 days
of purchase.
us at our
XMARK Fitness help line. We have trained service technicians on site to
take care of you, our valued customer.

NOTE: Hand tighten bolts and nylon nuts until machine is fully
assembled.
SAFETY PRECAUTIONS
SAFETY INFORMATION WARNING!
Prior to assembly, remove components from the box and verify that all the listed parts
were supplied.
Before using this unit or starting any exercise program, consult your physician.
This is especially important for persons over the age of 35 and/or persons with pre-
existing health problems. XMARK Fitness assumes no responsibility for personal
injury or property damage sustained by or through the use of this product.
It is the owner’s responsibility to ensure that all users of this unit have read the
Owner’s Manual and are familiar with safety information and precautions.
• This unit should only be used on a level surface and is intended for indoor use
only. XMARK Fitness recommends an equipment mat be placed under the unit to
protect the floor or carpet and for easier cleaning.
• Wear comfortable, good-quality walking or running shoes and appropriate cloth-
ing. Do not use this unit with bare feet, sandals, socks or stockings!
• Always examine your unit before using to ensure all parts are in working order.
• Do not leave children unsupervised near or on the unit.
• Service to your unit should only be performed by an authorized service represen-
tative, unless authorized and/or instructed by a XMARK Fitness technician. Failure
to follow these instructions will void the warranty.
Important Safety Information
4

5
Assembly
Assembly Hardware
M12 x 70mm Allen Bolt (#20) QTY 12
M12 x 90mm Allen Bolt (#21) QTY 2
M12
Locknut (#24) QTY 18
M12Washer (#23)
QTY 20
M12 x 95mm Allen Bolt (#22) QTY 4
(#5) TOP FRAME (#19) COTTER PIN
(#8) LEFT SLIDE FRAME
(#1) LEFT FRONT UPRIGHT
FRAME TUBE
(#2) RIGHT FRONT UPRIGHT
FRAME TUBE
(#3) LEFT REAR UPRIGHT
FRAME TUBE
(#4) RIGHT REAR UPRIGHT
FRAME TUBE
(#9)
(#12) STEEL PLATE
(#11) DIP BAR
(#6) REAR WEIGHT SLIDE HOLDER (#7) FRONT WEIGHT SLIDE HOLDER
Prior to assembly, remove components from the box and verify
that all the listed parts were supplied.
Unpack all parts and place them in a clear area. Be sure to remove all packing material.
(#10) BASE FRAME
RIGHT SLIDE FRAME

6
STEP 1
Assembly
FRONT
REAR
16
16
24
24
23
23
23
23
24
20
20
23
24
20
24
23
23
20
NOTE: Hand tighten bolts and lock nuts until machine is fully assembled.
Upright Frames with Single Holes (1 & 2) should be positioned to the front of unit as
seen in picture. Attach to Base Frame (10) using M12x70 Bolts (20), M12 Washers (23)
and M12 Lock Nuts (24).
Upright Frames (3 & 4) should be attached to Base Frame (10) at rear of unit using
M12x70 Bolts (20), M12 Washers (23) and M12 Lock Nuts (24).
Numbers on the Upright Frame face the inside of the unit.

7
NOTE: Hand tighten bolts and lock nuts until machine is fully assembled.
STEP 2
Assembly
4
1
7
6
8
3
2
6
7
9
19
19
13
REAR
FRONT
11
11
Slide Left Slide Frame (8) to the Upright Frames (1 & 4) and use Locking Pop Pin (13)
to secure. Then slide Front Weight Slide Holder (7) and Rear Weight Slide Holder (8)
onto the Upright Frames (4 & 1). Secure them using the Locking Pop Pin (13). Repeat
this step to assemble the Right Side parts to the Upright Frames (2 & 3) and secure with
a Locking Pop Pin (13).
To install Dip Bars (11), insert end through holes in Right Side Frame (9) and secure in
place using Cotter Pins (19).

8
Note: Hand tighten bolts and lock nuts until machine is fully assembled.
STEP 3
Assembly
4
1
22
20
20
22
22 12
12
23
24 5
23
23
23
23
24
21
23
23
23
23
24
21
3
2
23
23 24
REAR
FRONT
Attach the Top Frame (5) to the Upright Frames and secure according to the above
illustration.

9
Exploded View
20
24
23
22 20
23 24
18
18
13
13
13
13
16
16
22 12
5
12
17
23
24
23
17
23
21 2324
21
23
23
24
23
23
24
24
24
23
23
23
23
24
20
20
23
24
20
24
23
23
20

10
Parts List
1 204054202503 UPRIGHT FRAME, LEFT FRONT XM - 4430 1
2 204054202503 UPRIGHT FRAME, RIGHT FRONT XM - 4430 1
3 204054203503 UPRIGHT FRAME, LEFT REAR XM - 4430 1
4 204054203503 UPRIGHT FRAME, RIGHT REAR XM - 4430 1
5 204054206503 TOP FRAME, XM - 4430 1
6 204042002503 WEIGHT SLIDE HOLDER, REAR XM - 4430 2
7 204042001503 WEIGHT SLIDE HOLDER, FRONT XM - 4430 2
8 204042005503 SLIDE FRAME, LEFT XM - 4430 1
9 204042004503 SLIDE FRAME, RIGHT XM - 4430 1
10 204054201503 BASE FRAME, XM - 4430 1
11 204042003503 DIP BAR, XM - 4430 2
12 204042004503 PLATE, REINFORCEMENT XM - 4430 2
13 802900300002 POP PIN, LOCKING T-SHAPED 8
14 307010000706 SLEEVE, 63.5X88.9-50X75 BLACK 16
15 202042008006 PAD, ROUND RUBBER BLACK 2
16 306010020042 SQUARE END FOOT 50 2
17 307010000270 PLUG, INNER SQUARE 50 BLACK 2
18 307010000956 HANDLR GRIP 2
19 306990000024 COTTER PIN 2
20 306010020753 ALLEN BOLT, M12X70 12
21 306010020757 ALLEN BOLT, M12X90 2
22 306010020758 ALLEN BOLT, M12X95 4
23 306010023105 WASHER, 12 20
24 306010022505 LOCK NUT, M12 18
25 306990000144 WRENCH, ALLEN S=6 1
26 299054204500 BOLT PACK, XM - 4430 1
27 308030000273 MANUAL XM - 4430 1
Key NO. Part No. Description Qty
XM-4430 Parts List