Yale Tri-Pack 50 Series User manual

Machine Screws
#7 Drill, 1/4-20 Tap
Self Drilling Screws
Wood and Metal
For Wood drill 3/16 hole
"DL" suffix (Delayed Action) is an optional
feature. A separate sheet is supplied
showing closer adjustments.
NOTE: For special applications a separate
door and frame preparation template is
packed with these instructions. Use this
instruction sheet for installation sequence
and closer adjustments only.
Doors should be hung on ball bearing or
anti-friction hinges.
A separate door stop is recommended.
Door and frame must be properly
reinforced.
Adjust closing time speed between 3 and 7
seconds from 90° to 0°.
These door closers should NOT be
installed on the exposed side (weather
side) of exterior doors.
Top Jamb
Installation
See Page 5
289A Soffit Plate
Used with Parallel
Arm Closers Only
Soffit Plate
CAUTION
CAUTION
An Incorrectly installed or improperly adjusted
door closer can cause property damage or
personal injury. These installation instructions
should be followed to avoid the possibility of
misapplication or misadjustment.
Installation Instructions
80-9350-2502-010 (12-09)
Non Hold Open Models
Sized
(Sizes 2,3,4,5,6)
52BC
53BC
54BC
55BC
56BC
Adjustable
(Sizes 3 thru 6)
51
(Sizes 1 thru 4)
51BF
Non Handed Door Closer
Tri-Pack
50 Series
Right Hand Door - RH
Left Hand Reverse - LHR
Left Hand Door - LH
Right Hand Reverse - RHR
Right Hand Door - RH
Left Hand Reverse - LHR
Right Hand Door - RH
Left Hand Reverse - LHR
Regular Arm
Installation
See Page 2
Left Hand Door - LH
Right Hand Reverse - RHR
Left Hand Door - LH
Right Hand Reverse - RHR
Top Jamb
Installation
See Page 5
Regular Arm
Installation
See Page 2
Parallel Arm
Installation
See Pages
3 & 4
Parallel Arm
Installation
See Pages
3 & 4
Main Arm
Connecting Rod Adjusting
Tube
Arm Assembly
Elbow
Screw
Weaker
-
Stronger
+
3/16”
#7
1/4-20
Spring Power Adjustment Screw
51(BF) Series Only
"BC" Valve
Pinion Cap
Closer
Size
Stamp "L"Valve "S"Valve
Standard Components Optional Components
1-4
Closer Body
Sleeve Nut and Bolt
Thru Bolt and Grommet Nut
Drill 9/32 thru from Closer Side
3/8 Drill other side
Drill 9/32 thru from Closer Side
3/8 Drill other Side
(Optional)
Metal Wood
214
Plate
Cover

3
2
7
1
3
4
Non Hold Open Door Closers — Regular Arm
5
Latch
Sweep
Parts
6
Backcheck
6
(152)
1-3/4
(44)
1-1/4
(32)
3/4
(19) 9-1/16
(230)
7/8
(22)
A
80-9350-2502-010 (12-09)
Opening
To 100°
101° to 120°
*121° to 180°
7
(178)
6
(152)
3-1/2
(89)
Dimension "A"
*Door/Wall/Hardware/Jamb
conditions permitting
Right Hand Shown
BC
LS
L
S
51(BF) Only
Spring Power Adjust
(If Necessary)
D
Inches
(mm)
— 2 —
PA
(2)
or
50 Series
G
Pinion Cap
or Optional Cover
Caution:
Don't completely
close valve
Optional
Cover
C
L
Y
S
Z
R
F
90°
EA
B
Stronger
+
Weaker
-
Stronger
+
Weaker
-
Slower
-
Faster
+
Slower
-
Faster
+
LS
Screw pinion cap onto pinion shaft
by hand or with a Phillips screw
driver - DO NOT OVER TIGTHEN.

Optional
214
Plate
Parts
Right Hand Shown
2
1
80-9350-2502-010 (12-09)
50 Series Non Hold Open Door Closers — Parallel Arm
34
Holes for 214
Plate only
Door
Opening
To 100°
101° to 130°
*131° to 180°
A
9-1/4
(235)
7-3/4
(197)
5-3/4
(146)
B
7-5/8
(194)
6-1/8
(156)
4-1/8
(105)
C
8-5/8
(219)
7-1/8
(181)
5-1/8
(130)
2-3/4
(70) 3/8
(10)
1/2
(13)
7/16
(11)
2
(50)
A
1-1/2
(38)
7
(178) 4
(102)
2-1/8
(54) 3-1/4
(83)
1/2
(13)
3/4
(19)
9-1/16
(230) C
L
C
B
Top of
Door
*Door/Wall/Hardware/Jamb
conditions permitting
Inches
(mm)
5
— 3 —
S
L
Place Arm on
Spindle
R
o
t
a
t
e
Remove Arm
from Spindle
Close Valves
LS
Latch
Sweep
Optional
Cover
See Step 6 on Page 4
Frame
Slower
-
Slower
-

Screw pinion cap onto
pinion shaft by hand or
with a Phillips screw driver -
DO NOT OVER TIGHTEN.
13 14
12
80-9350-2502-010 (12-09)
50 Series Non Hold Open Door Closers — Parallel Arm
11
Latch
Sweep
Backcheck
68
7
910
Spring Power Adjust
51(BF) only
(If necessary)
PA
BC
S
L
S
L
— 4 —
or
(2)
Assemble Arm
Arm Screw
Open Valves
Caution:
Don't completely
close valve
Pinion Cap
or Optional Cover
L
Y
S
Z
R
L
Y
S
Z
R
Left Hand
Door
Right Hand
Door
or
B
A
Flat
Flat
1-1/2
(38)
Caution:
Do Not
Back
Valves Out
Completely
Stronger
+
Weaker
-
Slower
-
Faster
+
Stronger
+
Weaker
-
Slower
-
Faster
+

Screw pinion cap onto pinion shaft
by hand or with a Phillips screw
driver - DO NOT OVER TIGHTEN.
(2)
6
1
3
2
7
5
4
50 Series Non Hold Open Door Closers — Top Jamb Arm
Latch
Sweep
Backcheck
9-1/16
(230) 3/4
(19)
1/2
(13)
6
(152)
1-1/2
(38)
1-3/4
(44)
C
L
A
80-9350-2502-010 (12-09)
Opening
To 100°
101° to 120°
*121° to 180°
7-1/2
(191)
6
(152)
3-1/2
(89)
Dimension "A"
*Door/Wall/Hardware/Jamb
conditions permitting
Right Hand Shown
BC
LS
L
S
51(BF) Only
Spring Power Adjust
(If Necessary)
Top of
Door
Inches
(mm)
— 5 —
D
B
A
PA
G
Parts
Caution:
Don't completely
close valve
A longer connecting
rod is required
for reveals greater
than 3" (76)
or
Pinion Cap
or Optional Cover
Optional
Cover
Reveal
C
L
Y
S
Z
R
F
90°
E
Slower
-
Faster
+
Slower
-
Faster
+
Stronger
+
Weaker
-
Stronger
+
Weaker
-

Backcheck
BC
Sweep
LS
Latch
L
S
— 6 —
5=55BC
4=54BC
3=53BC
2=52BC
6=56BC
To identify your model:
3-6=51
1- 4=51BF
Arm Placement in Shoe
= 8 Turns As Shipped
CLOSED
70°
10°
Spring Power Adjust
51 (BF) only
PA
Adjustment Chart
EXTERIOR
EXTERIOR
INTERIOR
INTERIOR
Regular Arm
Top Jamb
Regular Arm
Top Jamb
Regular Arm
Top Jamb
Regular Arm
Top Jamb
Parallel Arm
Parallel Arm
Parallel Arm
Parallel Arm
FULL 360° TURNS OF
1/8” POWER ADJUSTMENT
SCREW
FULL 360° TURNS OF
1/8” POWER
ADJUSTMENT SCREW
51BF
51
DOOR
TYPE
OF
INST. *34”
(0.85M)
36”
(0.90M)
40”
(1.00M)
44”
(1.10M)
48”
(1.20M)
11233
22
345
56
912
246911
35710 13
35710 13
5710 14 16
NOT
RECOMMENDED
USE 51
*18 FULL (360°) TURNS MAXIMUM AVAILABLE
MAXIMUM DOOR SIZE
Number of Turns Required
3-6
BE
Date
Code
or
or
7-1/2 % Stronger
7-1/2 % Weaker
(Use 1/8” Hex Wrench for this Adjustment)
(Use 1/8" Hex Wrench for these Adjustments)
+
-
Size
Code
Size
Code
Stronger
+
Weaker
-
Slower
-
Faster
+
Slower
-
Faster
+
Weaker
-
Stronger
+
Adjustments Page50 Series
80-9350-2502-010 (12-09)
An ASSA ABLOY Group brand
3000 Highway 74 East • Monroe, NC 28112
Tel: [phone] • Fax: [phone]
www.yalecommercial.com
Yale ® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2001, 2009, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
8
8