Yale YDC201 User manual

Option A –Regular Arm Installation
INSTALLATION
INSTRUCTIONS
Option A instructions: 1. Using the measurements from diagram A, mark
screw hole center locations. Mark four (4) hole locations on door for door closer
and two (2) hole locations on frame for arm shoe. 2. Drill pilot holes in door
and frame, drill 7/32″(5.5mm) diameter holes for wood screws or drill and tap
#7(.201″ diameter) for 1/4-20 machine screws. 3. Install adjustable forearm/arm
shoe to frame using screws (a) or (b). 4. Mount closer on door using screws
(c) or (d). SPEED ADJUSTING VALVES MUST BE POSITIONED TOWARD
HINGE SIDE. 5. Install main arm to top pinion shaft, perpendicular to door,
Secure tightly with arm screw/washer (e). 6. Adjust length of forearm so it is
perpendicular to frame when assembled to preloaded main arm. Secure forearm
to main arm with screw/washer (f). 7. Adjust closing speed, see page2 for
reference. 8. Snap pinion cap over shaft at bottom of closer or install (optional)
cover with small screw (j).
1
Option B –Top Jamb Installation
Option B instructions: 1. Using the measurements from diagram B, mark
screw hole center locations. Mark four (4) hole locations on door for door closer
and two (2) hole locations on frame for arm shoe. 2. Drill pilot holes in door
and frame, drill 7/32″(5.5mm) diameter holes for wood screws or drill and tap
#7(.201″ diameter) for 1/4-20 machine screws. 3. Install adjustable forearm/arm
shoe to door using screws (a) or (b). 4. Mount closer on frame using screws
(c) or (d). SPEED ADJUSTING VALVES MUST BE POSITIONED TOWARD
HINGE SIDE. 5. Install main arm to bottom pinion shaft, perpendicular to door,
Secure tightly with arm screw/washer (e). 6. Adjust length of forearm so it is
perpendicular to door when assembled to preloaded main arm. Secure forearm
to main arm with screw/washer (f). 7. Adjust closing speed, see page2 for
reference. 8. Snap pinion cap over shaft at bottom of closer or install (optional)
cover with small screw (j).
ARM SHOE
MAIN ARM
SPEED ADJUSTING VALVES
(Right Hand Door)
FOREARM
DOOR CLOSER
(Left Hand Door)
ARM SHOE
MAIN ARM
SPEED ADJUSTING VALVES
FOREARM
DOOR CLOSER
YDC201
YDC204
ARM SHOE
SPEED ADJUSTING VALVES
(Left Hand Door)
FOREARM
DOOR CLOSER
MAIN ARM
ARM SHOE
SPEED ADJUSTING VALVES
(Right Hand Door)
FOREARM
DOOR CLOSER
MAIN ARM
A
Hinge or Pivot
Diagram for Option A
1-1/4
(32)
1-3/4
(44.4)
9-1/16
(230)
6
(152)
7/8
(22)
3/4
(19)
Hinge or Pivot
A
3/4
(19)
1/2
(13)
1-3/4
(44.4)
6
(152)
Diagram for Option B
Inches (mm)
Dim. A
3-1/2
6
7
(89)
(152)
(178)
Door Opening
121°to 180°
101°to 120°
to 100°
9-1/16
(230)
1-1/2
(38)
Inches (mm)
Dim. A
3-1/2
6
7
(89)
(152)
(178)
Door Opening
121°to 180°
101°to 120°
to 100°
80-9316-8007-000 REV-1(3/17)

FOREARM
ARMSHOE
2
3
DOOR CLOSER ADJUSTMENTS
POWER ADJUSTMENT CHART
APPLICABLE
DOOR
WEIGHT
33∼56 LBS
(15∼30 Kg)
56∼99 LBS
(30∼45 Kg)
99∼143 LBS
(45∼65 Kg)
143∼187 LBS
(65∼85 Kg)
COUNTERCLOCKWISE FOR
NEGITIVE NUMBERS ( )
CLOCKWISE FOR
FULL NUMBERS (+)
OPENING CYCLE
CLOSING CYCLE
BACK CHECK
Adjusting Valve
4mm
Hex
Wrench
DECREASE
INCREASE
-14
-10
0 (PRESET)
+ 6
DOOR
CLOSER
SIZE
BF
1
2
3
4
Use 4mm Hex
Wrench
For this
Adjustment
CAUTION!! Do not turn speed adjusting valves more
than two (2) full turns counter-clockwise. Do not back
valves out of closer or a leak will result.
The closing force is adjustable from a size 1 to size 4, as outlined in ANSI Standard A156.4.
When these series of door closers are installed and adjusted to conform to ADA reduced
opening force requirements (5 lbs max.) for Interior doors, they may not have adequate
closing force to reliably close and latch door. Power adjustments charted on this page are
recommended where possible, to ensure proper door control.
By law the Americans with
Disabilities Act (ADA) may
require that door closer
installation comply with
accessibility guidelines.
DECREASE
INCREASE
FASTER
SLOWER
2
APPLICABLE
DOOR LEAF WIDTH
EXTERIOR
(SWING OUT)
INTERIOR
28 " (0.71m)
32 " (0.81m)
36 " (0.91m)
42 " (1.07m)
5 lb-f
32 " (0.81m)
36 " (0.91m)
42 " (1.07m)
48 " (1.22m)
FULL TURNS OF POWER
ADJUSTING SCREW
SWEEP
Adjusting
Valve
LATCH
Adjusting
Valve
Screw
Power
Adjusting
Left hand door shown,
reverse measurements for
right hand door application.
Hinge or Pivot
Main arm
Main arm
Left hand door
Right hand door
1
(25)
131°to 180°
°
101°to 130°
To 100°
Door Opening
Dim. B
4-1/8
6-1/8
7-5/8
(105)
(156)
(194)
Dim. A
5-3/4
7-3/4
9-1/4
(146)
(197)
(235)
3-1/4
(83)
B
9-1/16
(230)
1/2
(13)
A
7/16
(11)
Left hand door shown,
reverse measurements for
right hand door application.
3/8
(9.5)
2
(51)
2-3/4
(70)
3/4
(19)
Inches (mm)
Option C instructions: 1. Using the measurements from diagram C, mark
screw hole center locations. Mark four (4) hole locations on door for door closer
and four (4) hole locations on inside frame for parallel bracket.
2. Drill pilot
holes in door and frame, drill 7/32″(5.5mm) diameter holes for wood screws or
drill and tap #7(.201″ diameter) for 1/4-20 machine screws.
3.
Install Parallel
bracket to frame using screws (g) or (h).
4. Mount closer on door using
screws (c) or (d).
SPEED ADJUSTING VALVES MUST BE POSITIONED
AWAY
FROM HINGE SIDE. 5. Place main arm on closer pinion shaft, index
main arm - mark “L” or “R” with pinion flat as shown in Figure 1, Secure tightly
with screw/washer (e).
6.
Remove arm shoe from forearm (see figure2), install
Parallel bracket to end of forearm using the screw (i).
7. With door closed,
adjust length of forearm so that the tip of the main arm is approximately 1″
(25mm) away from being parallel with door, when connected to the forearm.
Secure with screw/washer (f).
8. Adjust closing speed, see below 9. Snap
pinion cap over shaft at bottom of closer or install(optional) cover with small
screw (j).
1
Figure 2
Diagram for Option C
80-9316-8007-000 ReV-1(3/17)
Option C –Parallel Arm Installation
Components
Screw Pack
1
1
⒠
⒡
Standard
Pinion
Cap
P-Bracket
1
⒤
⒞
⒜
Machine2
Machine4
⒟
⒝
Wood2
Wood4
⒣
⒢
Wood4
Optional
Machine4
FOREARM
BRACKET
PARALLEL
MAIN ARM
DOOR CLOSER
(Left Hand Door)
SPEED ADJUSTING
VALVES
FOREARM
BRACKET
PARALLEL
MAIN ARM
DOOR CLOSER
(Right Hand Door)
SPEED ADJUSTING
VALVES
Yale Locks & Hardware
Product Support Tel [phone] • www.yalelocks.com
Yale Locks & Hardware Is a division of Yale Security Inc., an ASSA ABLOY Group company.