Zamel Cet Ledix SLR-01 User manual

www.ledix.pl
Monochrome LED
controller
SLR-01
Cet Lighting Sp. z o.o.
PL 43-200 Pszczyna, ul. Zielona 27, Poland
tel: [phone], fax: [phone]
e-mail: [email protected], www.ledix.pl
10÷14 V DC / 0,22 W; IP20
weight: 25 g
Declaration of Conformity is on www.ledix.pl
MonochromeLED controller
SLR-01
The symbol means selective
collecting of electrical and electronic
equipment. It is forbidden to put
the used equipment together with
other waste.
CET Lighting Sp. z o.o. declares that
the equipment complies with the principal
requirements and other applicable rules
of the RTTE Directive.
SLR-01 controller is designed for cooperation with light sources equipped with LED diodes
and supplied with 10 ÷ 14 V DC. In connection with standard monochrome LEDIX ttings
and with other LED diode products in cooperation with transmitters of EXTA FREE wireless
control system the SLR-01 controller allows a function with switching on/switching o with-
out necessity to lay the cabling for the switches. In addition a brightening/dimming is pos-
sible for LED lighting connected with SLR-01.
Characteristic features:
• thecontrollerisdesignedtocarryoutsimplefunctionsconnectedwithlightingcontrol
such as: switching on/ switching off, bistable mode, time mode, brightening/dimming.
• possibility for wireless control system (EXTA FREE transmitters) or wired control system
(normally open contact),
• one transistor output (MOSFET) with maximum current capacity of 4 A,
• wide operation range (up to 230 m in the open area),
• small dimensions (easy mounting in a Ø60 junction box),
• low power consumption in the standby mode – controller is designed for continuous op-
eration .
Mounting in a Ø60
junction box
Mounting
indoor only
Co-operation
with EXTA FREE
transmitters
SLR-01 ENG Ver. 01
SCAN
the technical
data
10 ÷ 14 V DC
Monochrome LED controller
TYPE: SLR-01
A detailed mounting instruction is in the packaging

230 V AC 14 V DC
CAUTION !The device is designed for single-phase installation and must be installed
in accordance with standards valid in a particular country. Installation, connection
and control should be carried out by a qualied electrician sta, who act in accord-
ance with the service manual and the device functions.
1. Disconnect power supply by the phase fuse, the circuit-breaker or the switch- discon-
nector combined to the proper circuit.
2. Check if there is no voltage on connection cables by means of a special measure equip-
ment.
3. Connect the power supply to 230 V AC.
4. Connect the cables to the appropriate control terminals in accordance with the con-
nection diagram (in case of radio control only, it is not required to connect the cables to
IN1, IN2 terminals).
5. Mount the controller in the Ø60 junction box.
6. Switch on the power supply from the mains.
7. Add selected transmitters to the controller (a description is in TRANSMITTERS’ PRO-
GRAMMING section) and check their proper functioning.
SLR-01 controller is designed for cooperation with monochrome LEDIX standard lamps
and with other LED products supplied with 10÷14 V DC (monochrome tapes, LED strips
and modules, LED lamps). The controller controls the functions: switching on/ switching
o by means of one or two buttons, brightening/dimming and automatic switching o
after a programmed time (with gradual dimming within 10 s).
The controller features:
•tocontrolastandardmonochromeLEDttingsoftheLEDIXsystem,
•to control other monochrome LED products supplied with 10÷14 V DC,
•to carry out the functions: switching on/ switching o, brightening/dimming, timer
mode with turning o,
•radio control (transmitters of EXTA FREE system) or wired control system (inputs IN1,
IN2),
•PWM output of the MOSFET transistor – maximum current capacity of 4 A,
•9-bit fast PWM outputs allow the brighting/dimming function to be very uent,
•low power consumption in the standby mode (0.25 W) – controller is designed for con-
tinuous operation (ECOLINE).
TECHNICAL DATA
MOUNTING
DESCRIPTION
DIAGRAM
APPEARANCE
Nominal supply voltage: 10 ÷ 14 V DC
Nominal power consumption: 0,22 W
Number of channels: 1
Maximum current in the channel: 4 A
Controlling signal: PWM 9-bit
Number of wired outputs: 2 (IN1, IN2)
Radio transmission: 868,32 MHz
Transmission method: One-way without conrmation
Coding: Yes – transmission with addressing
Maximum number of transmitters: 32
Range: Up to 230 m in the open area
Time adjustment: 1 s ÷ 18 h
Number of connection terminals: 6
Maximum cross-section of connection cables: Up to 2,5 mm2
Ambient temperature range: -10 ÷ +55 oC
Mounting: In a Ø60 junction box
Casing protection degree: IP20
Protection class: III
Dimensions: 47,5 x 47,5 x 20 mm
Weight: 25 g
Reference standard: PN-EN 60669; PN-EN 61000
CAUTION! Nominal output voltage of the power supply (10÷14 V DC) and its nominal
output power must be adjusted for LED light source connected to the controller.
Wired control terminals
(IN1, IN2)
Output terminals (+, -)
Power supply terminals (+, -)
Optic signalling of the
controller’s operation
Programming button
MAXIMUM CURRENT CAPACITY:
Up to 40 W for LED diode products supplied with 10 V
Up to 48 W for LED diode products supplied with 12 V
Up to 56 W for LED diode products supplied with 14 V
ZNP, ZNN or ZNM series of the
power supply in 14 V DC version
Example of the
LEDIX series
LED tting

t > 3s t > 3s
t > 3s
t > 3s t > 3s
10s 10st
p
t
p
t
p
t<t
p
t > 3s t > 3st > 3s
Switch ON/OFF with BISTABLE button of the transmitter + brightening/dimming function
The controller changes the output
function periodically after short
pressing of the transmitter’s push-
button always the same. Holding
the transmitter’s push- button
longer (>3s) starts the brightening
function up to the maximum. The dimming function is available after releasing and holding
of the transmitter’s push-button.
Switch ON/ switch OFF with two push-buttons of the transmitter
+ brightening/dimming function
The controller switches on the output after
pressing of the push-button programmed
as „ON” and switches o the output after
pressing of the push-button programmed
as „OFF”. The brightening function is carried
out by holding the button„ON” for a longer
time (>3s). The dimming function is carried
out by holding the button„OFF” for a longer
time (>3s).
Time mode
The output is switched on
after short pressing of the
transmitter’s button. The
output switches o auto-
matically if the programmed
time is reached (1 s to 18 h) or if the same push-button of the transmitter will be pressed again.
If the programmed time is reached then switching o is carried out during t=10 s as uent
slowly dimming. If the button will be released again when the dimming function is active, then
the time will be counted from the beginning – time retrigable function.
IN1 input – short applying „+” potential to IN1 input will start the switch on/switch o se-
quence. Longer (>3 s) applying „+” potential to IN1 input will start the brightening func-
tion up to maximum. Dimming function is available up to minimum when „+” potential is
removed and again applied to IN1 input. The input is adapted for co-operation with pull-up
switches
IN2 input – applying„+”potential to IN2 input activates superior switching on of the output
of the SLR-01 controller. At the time the function for radio control is blocked. If applying„+”
potential to IN2 input is removed the controller output is switched o and radio control
function is unblocked. The input can be used for co-operation with voltage-free NC contact
for example with twilight switch.
Mode 1 – only motion sensor
SLR-01 controller must be programmed in the time mode with a minimum time adjustment
of 15 s. If the RCR-01 motion sensor detects motion in the detection eld and sends a signal
to the controller and the programmed time is counted from the beginning. LED light tting
is switched on so long as motion is detected in the detection zone of the RCR-01 sensor.
Mode 2 – motion sensor with a twilight switch
SLR-01 controller must be programmed in the monostable mode. The RCR-01 motion sensor
detects the motion in the detection eld and sends„ON”signal to the controller.„OFF” signal
will be sent 20 s after stopping of the motion in the detection zone.
OPERATION  RADIO CONTROL
FUNCTIONS WITH IN1 AND IN2 INPUTS
COOPERATION WITH RADIO MOTION SENSOR RCR01
Press NAUKA push-
button in RCR-01
and then release
the button. Red
LED diode switches
on under the lens
(constant signal)
Press NAUKA
push-button in
RCR-01 and then
release it. Red
LED diode will
light switches
on under the
lens (constant
signal)
Press PROG
push-button to
enter the SLR-01
programming
mode. The LED
diode in the
controller switches
on (constant
signal)
Press again
NAUKA
push-button
in RCR-01for a
longer time
Press NAUKA push-
button in RCR-01,
and then release
it. The LED diode
in the controller
switches on (rst
the signal pulsates,
next the signal is
constant)
Press PROG
push-button to
enter the SLR-01
controller in the
programming
mode. The
LED diode in
the controller
switches on
(constant signal)
Press NAUKA push-
button in RCR-01 and
then release the button.
Red LED diode in the
controller switches on
(the signal pulsates) and
then switches o - THE
SENSOR IS ADDED. Wait
until the LED red diode in
RCR-01 switches o
Release the
NAUKA button
in RCR-01. The
LED diode in the
controller will
light up (rst the
signal pulsates,
next the signal is
constant)
Press NAUKA push-
button in RCR-01
and then release
the button. Red LED
diode switches on
in the controller
(ashing signal) and
then goes out – THE
SENSOR IS ADDED.
Wait until the LED
diode in RCR-01
switches o

RADIO TRANSMITTERS PROGRAMMING TIME PROGRAMMING
RADIO TRANSMITTERS DELETION
BISTABLE mode:
SWITCH ON/SWITCH OFF mode (two push-buttons):
TIME mode (one push-button):
An exemplary programming procedure with the use of P-257/2 remote control. The
procedure for the rest of radio EXTA FREE transmitters is analogous. CAUTION: Every
transmitter can cooperate with SLR-01 in a dierent mode, depending on how they
were added to the device. One transmitter can be added during one programming
cycle. Full memory is signalled with pulsating LED red diode.
Press the transmitter’s
push-button for a longer
time. LED red diode
switches on (rst signal
pulsates, next the signal is
constant)
Press and release
transmitter’s push-button.
LED red diode switches on
(rst the signal pulsates,
next the signal is constant)
Press and release the rst
transmitter’s push-button.
LED red diode switches on
(rst the signal pulsates,
next the signal is constant)
Press and release the same
transmitter’s push-button.
LED red diode switches on
(the signal pulsates) and
next it switches o - THE
TRANSMITTER IS ADDED
Press and release the
same transmitter’s
push-button. LED red
diode switches on (the
signal pulsates) and
next it switches o - THE
TRANSMITTER IS ADDED
Press and release the
second transmitter’s
push-button. LED red
diode switches on (the
signal pulsates) and
next it switches o - THE
TRANSMITTER IS ADDED
Press PROG push-button of
SLR-01 device for a longer time
until LED red diode switches on
(constant signal). Next release
PROG push-button
Press PROG push-button of
SLR-01 device for a longer time
until LED red diode switches on
(constant signal). Next release
PROG push-button
Press PROG push-button of
SLR-01 device for a longer time
until LED red diode switches on
(constant signal). Next release
PROG push-button
Maximum time is 18 hours.
Press PROG push-button of SLR-01
device for a longer time till LED red
diode switches on (constant signal).
Next release the PROG push-button.
Wait (for about 5 seconds) till LED
red diode switches on (rst signal
pulsates, next the signal is constant)
After the adjusted
time is reached (the
number of LED red
diode ashes) press
PROG push-button
and then release it
- TIME IS ADDED
Press PROG push-button
of SLR-01 device and
then release it. LED red
diode switches o and
then switches on (signal
pulsates). Every LED diode
pulse equals 1 second
Press PROG push-button
of SLR-01 device for a
longer time.
After 5 seconds LED red
diode switches on (the
signal pulsates) and then it
switches o.
Release the push-button
in SLR-01 - MEMORY IS
DELETED.
OPERATION TABLE
Symbol
RNK-02 RNK-04
P-256/8 P-257/2 P-257/4
RNM-10
RNP-01 RNP-02
RNL-01
RTN-01
RCR-01
RTI-01
RXM-01
P-260
SLR-01
180 180 230 180 180 230 160 160 160 200 160 160 230 -
CAUTION:The given range concerns open area - an ideal condition without any natural
or articial obstacles. If there are some obstacles between a transmitter and a receiver,
it is advisable to decrease the range according to: bricks: from 10 to 40 %, wood and
plaster: from 5 to 20 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%
, glass: from 10 to 20 %. Over- and underground medium and high electrical power
lines, radio and television transmitters, GSM transmitters set close to a device system
have also a negative inuence on the range.
1 s 2 s n s