SRW-01 - roller blind control module
TECHNICAL DATA
Rated supply voltage: 230 V AC
Relay contact parameters: 2 x NO 5 A / 250 V AC
Rated mains frequency: 50 / 60 Hz
Rated power consumption: 1.2 W
Transmission: Wi-Fi 2.4 GHz 802.11 b/g/n
Operating range: Wi-Fi range
Number of inputs: 2
Compatible connectors: monostable (bell buttons), bistable (standard roller blind switches)
Number of output channels: 2
Relay contact parameters: 2 x NO 5 A / 250 V AC
Maximum output
current-carrying capacity: 2 x 5 A / 250 V AC: roller blind drives – 350 W
Number of connection
terminals: 6 (conductor cross-section up to 2.5 mm2)
Enclosure mounting: installation box Ø 60 mm
Operating temperature range: -10 to +55°C
Enclosure protection rating: IP20
Dimensions: 47.5 × 47.5 × 23 mm
Weight: 0.046 g
Reference standards: EN 60669-1, EN 60669-2-1, ETSI EN 300 328,
ETSI EN 301 489-1, EN 301 489-17
INSTALLATION CONSIDERATIONS:
1. Do not install receivers close to one another (if possible, maintain spacing of at least 15 cm between
individual receivers). In particular, avoid installing receivers on top of one another. It may result in Wi-Fi
connectivity problems.
2. Observe the maximum output current-carrying capacity value:
• drives: 350 W – Class AC3
3. During installation, ensure the module is not subjected to direct water impact or operation in high
moisture content environments. The range of temperatures in the installation location should be from
-10 to +55°C.
4. SRW-01 modules are to be installed indoors. When installed outdoors, it must be secured in an
additional airtight installation box.
5. Installation connectors for wired control can be connected to inputs IN1 and IN2 of the SRW-01
receiver. The inputs operate with monostable or bistable connectors. SRW-01 modules are to be
mounted in installation boxes. The enclosure dimensions facilitate installation in ush-mounted
(minimum Ø 60) and surface-mounted boxes. For ush mounting, “pocket boxes” are recommended.
6. After receiver installation, check its operation, ensuring that the LED is ON.
INSTALLATION
• SRW-01 modules are to be mounted in installation boxes. The enclosure dimensions facilitate
installation in ush-mounted (minimum Ø 60) and surface-mounted boxes. For ush mounting,
“pocket boxes” are recommended.
• Connect the device to single-phase mains, according to applicable standards. The device must be
installed, connected and adjusted by qualied electricians familiar with its operation manual and
functions. Due to safety reasons, do not install the device with its enclosure removed or damaged,
as it poses an electric shock risk.
Download the SUPLA app on your smartphone.
If you already have a SUPLA account and are logged in the app, go to the next step.
If you do not have an account, click: “Create an account” in your app.
Enter your email address and password in the form displayed.
Check your email inbox. Conrm registration by clicking the activation link sent in the message.
Next, log in the app using your email address.
Connect the device to power using the diagram placed on its enclosure.
After logging in, select “Add a device” from the menu. The “Add a device” wizard is started. Take steps
according to messages displayed on the screen, until the set-up process is successfully completed.
Following successful set-up, the device connects with a Wi-Fi router. This is indicated by solid LED light.
You can also connect to the “ZAMEL-SRW-01…” Wi-Fi network. Enter the following address: “192.168.4.1”
in your browser window and provide your Wi-Fi data and email address used to register your account,
and press the “SAVE” button. The “Data saved” message conrms that access settings have been saved
successfully. Next, you must press the CONFIG button to store the settings.
control roller blinds
Control roller blinds remotely using SUPLA app on your smartfon!
add a device
create an account / log in
@
connect to power
install the app
DETAILED OPERATION MANUAL AVAILABLE AT:
https://supla.zamel.pl/produkt/srw-01/
