Zamel RNK-02 User manual

2-CHANNEL BUTTON RADIO TRANSMITTER RNK-02
INSTRUCTION MANUAL
ZAMEL Sp. z o.o.
ul. Zielona 27, 43-200 Pszczyna, Poland
tel. [phone], fax [phone]
www.zamelcet.com, e-mail: [email protected]
VER. 004_20.05.2011
APPEARANCE
TECHNICAL DATA
RNK-02
Input rated voltage: 3 V DC
Battery type: CR2032
Battery working life: 3 ÷ 5 years (depending on use)
Number of channels: 2
Transmission: radio 868,32 MHz
Transmission way: unidirectional
Coding: addressing transmission
Range: up to 250 m in the open area
Optical signalling of transmission/battery discharge: LED red diode
Ambient temperature range: -10 ÷ +55 oC
Operating position: free
Casing mounting: wall plugs, double-sided adhesive tape
Casing protection degree: IP20 (EN 60529)
Protection level: III
Pollution degree: 2
Dimensions: 90 x 80 x 11,5 mm
Weight: 0,038 kg
Reference standard: ETSI EN 300 220-1,
ETSI EN 300 220-2
FEATURES:
DESCRIPTION
●2-channelbuttonradiotransmitter,
●remotecontrolofEXTAFREEreceivers,
●possibility of independent control of two
receivers,
●widerangeofoperation(upto250m),
battery powered,
●easy installation and mounting possibility
in any place,
●sendinginformationandbatterystatusare
optically signalled,
●possibility of simultaneous switching
on / off of any number of EXTA FREE
receivers.
RNK-02 button radio transmitter is an
EXTA FREE wireless control, radio device.
It is used to realise control functions: switch-
ing on, switching off, brightening/dimming,
putting up/down roller blinds, time opera-
tion mode. The transmitter can be mounted
on any surface including glass, wood, etc.
thanks to its little size and weight, and ex-
ternal power supply which is not necessary.
The symbol means selective
collecting of electrical and
electronic equipment. It is forbidden
to put the used equipment together
with other waste.
Optical signalling of transmitter’s operation
Button
Base

VER. 004_20.05.2011
MOUNTING, FUNCTIONING
APPLICATION
Bypressingthebutton,thetransmittersendsasignalwith868,32MHzfrequencywhichcontrolsEXTAFREEreceivers.Device pro-
gramming procedure (adding a transmitter to a receiver’s memory) is described in particular EXTA FREE manual instructions.
The device range (up to 250 m depending on a receiver) can be increased by means of a retransmitter or few RTN-01 retransmitters.
The device can be mounted in any place by means of double-sided adhesive tape or wall plugs 5 x (3 x 30) mm.
Mounting by means of wall plugs:
1. Remove the button - to do it press the button on
one side, and on the other side put a screwdriver
intoaslotandliftupthebutton(Fig.1)
2.Finda placeonthe walltomount thetransmitter,
make two holes corresponding mounting holes
from the transmitter’s base.
3. Set wall plugs in the holes.
4.Fix the base by means of screwing screws into
wall plugs.
5. Place the button again.
BATTERY CHANGE
Battery discharge status is signalled by several
LED red diode ashes during transmission time.
1.Removethebutton(Fig.1).
2. By means of a screwdriver lever up the printed-
circuit board releasing the bottom latch (Fig. 2),
and remove it from the base.
3.Removethebatteryfromthelatch(Fig.3).
4. Mount a new battery. Watch battery polarisation
marked on the latch. Wrong battery mounting may
cause device damage.
5. Put the removed printed-circuit board back
in the base.
6. Put the button back.
CAUTION: While changing the battery, it is suggested to press any of the buttons for about 5 seconds before putting it into
a latch. Next press transmission button several times to check its operation. If the transmitter does not work properly repeat the
battery change procedure.
RNK-02 button radio transmitter controls
radio lighting switch operation RWL-01
(switch on/switch off),
radio receiver ROP-01 (switch on/switch off),
or remote control socket RWG-01
(switch on/switch off).
COOPERATION AND OPERATION RANGE
Symbol ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01
RNK-02 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m
RNK-04 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m
CAUTION: The given range concerns open area - an ideal condition without any natural or articial obstacles. If there are some obstacles between a transmitter
and a receiver, it is advisable to decrease the range according to: wood and plaster - from 5 to 20, bricks - from 10 to 40 %, reinforced concrete - from 40
to 80%, metal - from 90 to 100% , glass - from 10 to 20%. Over- and underground medium and high electrical power lines, radio and television transmitters,
GSM transmitters set close to a device system have also a negative inuence on the range.
рис.1
рис.2 рис.3
WARRANTY CARD
There is 24 months guarantee on the product
1. ZAMEL provides a two-year warranty for its products.
2. The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances
b) defects resulting from incorrect installation or operation of ZAMEL products; c) defects resulting from any changes made by CUS-
TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold; d) defects resulting
from force majeure or other aleatory events for which ZAMEL is not liable; e) power supply (batteries) to be equipped with a device
in the moment of sale (if they appear);
3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect.;
4. ZAMEL will review complaints in accordance with existing regulations.;
5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL.
6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy
between the goods and the contract.
Salesman stamp and signature, date of sale
The ZAMEL company
devices which are
characterised with this sign
can cooperate
with each other.