OPERATION
Before retransmitter’s operation start it is important to set switches,
which are in the back part of a device, according to a suitable com-
bination. If only one retransmitter is used its switches should be set in
combination”a’ presented in Fig. 1.
CAUTION! Only 4 retransmitters can operate in the transmitters
operation range.
In a situation where few retransmitters are used (maximum 4), the
switch of the following retransmitter should be set in a combination dif-
ferent from the combination of the other retransmitters. Suggested setting sequence for the following retransmitters according to Fig. 1.
COOPERATION AND OPERATING
Symbol ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01
RNK-02 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m
RNK-04 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m
P-256/8 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m
P-257/4 (2) 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m
RNM-10 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m
RNP-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m
RNP-02 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m
RNL-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m
RTN-01 200 m 200 m 200 m 200 m 200 m 250 m 200 m 250 m 250 m 200 m 250 m
RCR-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m
RTI-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m
RXM-01 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m
* - 1-channel transmitters do not cooperate with roller blind controllers.
CAUTION: The given range concerns open area - an ideal condition without any natural or articial obstacles. If there are some obstacles between a transmitter and a receiver,
it is advisable to decrease the range according to:
wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%, glass: from 10 to 20 %. Over- and underground medium
and high electrical power lines, radio and television transmitters, GSM transmitters set close to a device system have also a negative inuence on the range.
PROGRAMMING
CAUTION! By adding next retransmitters to increase the range of one transmitter, it is required to add this transmitter to every
retransmitter. One transmitter can be added to a retransmitter during one programming cycle.
RADIO TRANSMITTERS ADDITION (An exemplary programming procedure of P-257/2 remote control)
RADIO TRANSMITTERS DELETION
Fig. 2. Operation with maximum number of retransmitters.
Press and release transmitter’s push-button.
LED red diode switches on (rst signal
pulsates, next the signal is constant).
Press and release the same transmitter’s
push-button. LED red diode switches on
(the signal pulsates) and next it switches off
- THE TRANSMITTER IS ADDED.
Press PROG push-button of RTN-01 device
for a longer time until LED red diode switches on
(constant signal). Next release PROG push-button.
Press PROG push-button of RTN-01
device for a longer time.
After 5 seconds LED red diode switches on
(signal pulsates) and then it switches off.
Release the push-button in RTN-01 -
MEMORY IS DELETED.
a b c d
Fig. 1. Possible switch settings.
The ZAMEL
company devices
which are characterised
with this sign
can cooperate
with each other.
WARRANTY CARD
1. ZAMEL provides a two-year warranty for its products.
2. The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances
b) defects resulting from incorrect installation or operation of ZAMEL products; c) defects resulting from any changes made by CUS-
TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold; d) defects resulting
from force majeure or other aleatory events for which ZAMEL is not liable; e) power supply (batteries) to be equipped with a device
in the moment of sale (if they appear);
3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect.;
4. ZAMEL will review complaints in accordance with existing regulations.;
5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL.
6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy
between the goods and the contract.
There is 24 months guarantee on the product
Salesman stamp and signature, date of sale
T
r
a
n
s
m
i
t
t
e
r
R
e
c
e
i
v
e
r
