Zest 4 Leisure Brighton Corner Arbour User manual

Assembly Instructions
(W x D x H): 2.20m x 2.20m x 2.49m
Product Name: Brighton Corner Arbour
Pressure Treated products should not be treated with any other products for the first month.
PLEASE KEEP THIS INSTRUCTION
Zest4Leisure
01352 752555 option 1 –[e-mail]
V2-05.16

Brighton Corner Arbour Assembly Instructions
Requires 2 person assembly.
Tools required:Adjustable Spanner, Corded / Cordless Drill, Pozi-drive Bit /
Screwdriver, 3mm Drill Bit, required in order for you to drill all screw holes before
construction, tape measure. The colour version of this document can be downloaded
from: www.zest4leisure.co.uk/downloads/category/C1
Brighton Corner Arbour Pack List
Item Description Quantity
A Notched Post 4
B Full Post 3
C Seat 2
D Table Leg 1
E Ring Beam 4
F Back Rest 2
G Table Top 1
H Back Panel 4
J Side Panel 4
K Arm Rest 2
L Diagonal Front Brace 2
M Rear Corner Brace 1
N Centre Brace 1
O Finial Support 1
P Finial 1
Q Roof Panel 4
Fixings
60mm Screws 104
120mm Bolts, Washers & Nuts 7
www.zest4leisure.co.uk

Brighton Corner Arbour Assembly Instructions
Requires 2 person assembly.
Tools required:Adjustable Spanner, Corded / Cordless Drill, Pozi-drive Bit /
Screwdriver, 3mm Drill Bit required in order for you to drill all screw holes before
construction, tape measure. The colour version of this document can be downloaded
from: www.zest4leisure.co.uk/downloads/category/C1
www.zest4leisure.co.uk

Please take a few moments to check all pack contents listed.
Assembly requires 2 persons. Tools required: Adjustable Spanner,
Corded/Cordless Drill, Pozi-drive Bit/Screwdriver, 3mm Drill Bit required in order
for you to drill all screw holes before construction, tape measure.
Brighton Corner Arbour is now complete.
1. Attach 2no Notched Posts A and 1no Full Post B to seat C (ensure notches face outwards) using 3no
Bolts, Washers & Nuts –1no per post. See Fig.1a & 1b.
Further attach Table Leg D to Seat C using 1no Bolt, Washer & Nut –See Fig.1c
2. Attach 2no Notched Posts A and 1no Full Post B to remaining seat C (ensuring notches facing outwards)
using 3no Bolts, Washers & Nuts –1no per post. See Fig.2a.
Attach seat and posts assembly to Table Leg D using 2no 60mm Screws –Fig.2b
3. Locate Ring Beam E into notches of Notched Posts A (right side front facing the arbour), flush with
Notched Post A as shown in Fig.3a. Using Side Panel J to set the distance between Notched Posts A, fix
Ring Beam E in position using 4no 60mm Screws –2no per post.
Working clockwise, fix remaining Ring Beams E to posts to form a square, using 2no 60mm screws per post
- Figs.3b, 3c, 3d & 3e. Also attach Full Post B as shown in Fig.3d. Ensure each Ring Beam E is also
attached to inner face of the previous Ring Beam E.
4. Position Back Rest F onto Seat C (Fig.4a) and fix in position using 4no 60mm Screws –2no to Seat F
(see arrows in Fig.4a) and 2no to posts (Fig.4b). Repeat procedure for remaining Back Rest F.
5. Position Table Top G onto Table Leg D and between Full Posts B as shown in Fig.5a. Ensuring Table Top
G is levelled, fix in position through Table Top G battens using 4no 60mm Screws –1no into each Full Post
B & 1no into Table Leg D. See Fig.5b.
6. Attach 2no Back Panels H to posts to rear of seat assembly (ensure top Back Panel H meets the
underside of Ring Beam E) as shown in Fig.6a and 6b using 12no 60mm screws –6no per panel. Repeat
procedure for remaining Back Panels H.
7. Locate 2no Side Panels J between Notched Posts A (ensure top Side Panel J meets underside of Ring
Beam E and bottom Side Panel J is in line with the underside of Back Panel H) as shown in Fig.7a & 7b. Fix
in position using 8no 60mm Screw –4no per Side Panel J. Repeat procedure for remaining Side Panels J.
8. Attach Arm Rest K to Side Panel J as shown in Fig.8 using 2no 60mm Screws. Repeat procedure for
remaining Arm Rest K.
9. Attach Diagonal Front Brace L to Notched Post A and Ring Beam E using 2no 60mm Screws. Repeat
procedure for remaining Diagonal Front Brace L.
10. Attach Rear Corner Brace to Ring Beams E as shown in Fig.10 using 4no 60mm Screws –2no per side.
11. Attach Centre Brace N to Ring Beams E as shown in Fig.11 using 4no 60mm Screws –2no per side.
12. Locate Finial Support O between front Ring Beams corner and middle of Centre Brace N (Fig12a). Fix in
position using 4no 60mm Screws as shown in Figs.12a and 12b.
13. Locate Finial P onto Centre Brace N (1240mm from edge of front corner as shown in Figs.13a & 13b)
and fix in position using 2no 60mm Screws –Fig.13c.
14. Position Roof Panel Q onto Finial P and Ring Beam E and attach to Finial P using 1no 60mm Screw as
shown in Fig.14a. Repeat procedure for remaining Roof Panels Q.
Ensuring Roof Panels Q are correctly aligned, fix to Ring Beams E using 12no 60mm Screws –3no per Roof
panel Q –Fig.14b.

www.zest4leisure.co.uk
1b1a
1c 2a
2b 3a
3b 3c

www.zest4leisure.co.uk
3e3d
4a 4b
5a 5b
6a 6b

www.zest4leisure.co.uk
7b7a
8 9
10 11
12a 12b

www.zest4leisure.co.uk
14a
13a
14b
13b
13c