Zest 4 Leisure HOLLYWOOD SWING User manual

Zest 4 Leisure
0845 890 2357 [email protected]
ASSEMBLY INSTRUCTIONS
HOLLYWOOD SWING
Technological adjustments reserved
ITEM CODE - SEATHWS
PLEASE KEEP THIS INSTRUCTION
21460

Hollywood Swing Seat
Requires 2 person assembly.
Tools required:- Hammer, Corded/ Cordless Drill, Tape Measure, Pozidrive
Bit/Screwdriver, 3mm Drill Bit, Pencil.
See Swing Hammock Base Instructions.
1) Lay out 2no posts (5) (with counter-bore facing down) and position upper
and lower crossboards (3 & 4) see fig1. Align all holes and insert 8no
M8x100mm bolts (B). NB Ensure that offset hole in upper cross board (3) is
biased towards right hand post.
2) Carefully turn over the `A` frame and fit washers and nuts to all bolts with
supplied socket spanner. NB Do not tighten at this stage.
Repeat stages 1 & 2 for second `A` frame assembly.
3) Insert 2no M10 swing holders (F) through holes in swing beam (2) so that
threaded section emerges in counterbore, as shown in fig. 1. Fit washers and
cap-nuts to both bolts, align swing holders with swing beam and fully tighten
cap-nuts.
4) Align top holes on `A` frames with outermost holes on swing beam (2) and
insert 2no M8x100mm bolts (B) through `A` frames and swing beam.
5) Attach bracings (6) to swing beam (2) using 4no M8x90mm bolts (C) and to
upper crossboards (3) using 2no M8x80mm bolts (D), washers, nuts and cap-
nuts. See fig 1.
6) Pre-drill protection board (1) as illustrated in fig. 1, and fix to swing beam
(2) using 4no 4x50mm screws (A).
7) Carefully lift assembly into upright position and ensure all nuts / washers
are in place and are fully tightened.
The Base assembly is now complete.

P.T.O.
See Swing Hammock Bench Instructions.
1) Interlock bench back (8) and bench (9), align bolt holes and fix using 6no
M8 x 45mm bolts (E). NB Do not fully tighten nuts at this stage.
2) Assemble connection braces (11) to arm rests (10) as per diagram, by
locating dowels and pre- drilled holes, and secure using 2no 4x50mm screws
(A).
––
3) Attach the arm rests to the bench assembly using 4no M8 Eye bolts (G)
nuts and washers. Fully tighten all nuts on bench assembly at this stage.
4) Pass narrow link on long front chain (I) through hole in armrest and attach
to front eye bolt using shackle (J). Attach short back chain (H) to back eye bolt
using shackle (J). Repeat for opposite side of bench.
5) Hang bench assembly from swing hangers (F) using 2no spring hooks (K).
Ensure that chains hang freely i.e. no twists.
The assembly is now complete.

Figure 1

No. Picture Description/name Dimensions [cm] Number
1
gableboard 3,5x15,5x222,5 1
2
beam 4,5x15,5x222,5 1
3
short strut 3,5x15,5x55,5 2
4
long strut 3,5x15,5x120 2
5
pole 8,5x8,5x226 4
6
strut 3,5x9x65 2
8
bench 9,5x59,5x152,4 1
9
seat 14x57,5x152,4 1
10
arm rest for bench 3,4x9,3x61,5 2
11
connection brace betw. seat+arm rest 3,5x7x33 2
Parts list item code 42580 HOLLYWOOD Swing
A
wood screws Ø4x50 mm 6
B
bolt and nut M8x100 mm 16
C
bolt and nut M8x90 mm 4
D
bolt and nut M8x80 mm 2
E
bolt and nut M8x45 mm 6
F
tab for bench 2
G
binding screw 4
H
short chain 2
I
long chain 2
J
shackle for bench 4
K
spring hook
2
K
spr
i
n
g h
oo
k
2
42580 2010‐01‐21